BS ISO 7573-2008 en_5566 Technical product documentation - Parts lists《技术产品文件.部件清单》.pdf
《BS ISO 7573-2008 en_5566 Technical product documentation - Parts lists《技术产品文件.部件清单》.pdf》由会员分享,可在线阅读,更多相关《BS ISO 7573-2008 en_5566 Technical product documentation - Parts lists《技术产品文件.部件清单》.pdf(16页珍藏版)》请在麦多课文档分享上搜索。
1、BS ISO 7573:2008 ICS 01.110 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Technical product documentation - Parts listsThis British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 November 2008 BSI 2008 ISBN 97
2、8 0 580 59617 9 Amendments/corrigenda issued since publication Date Comments BS ISO 7573:2008 National foreword This British Standard is the UK implementation of ISO 7573:2008. It supersedes BS ISO 7573 : 1983 which is withdrawn. The UK participation in its preparation was entrusted to Technical Com
3、mittee TDW/4, Technical product realization (TPR). A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance
4、 with a British Standard cannot confer immunity from legal obligations.BS ISO 7573:2008Reference number ISO 7573:2008(E) ISO 2008INTERNATIONAL STANDARD ISO 7573 Second edition 2008-11-01 Technical product documentation Parts lists Documentation technique de produits Nomenclatures de composantsBS ISO
5、 7573:2008 ISO 7573:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing
6、. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be fou
7、nd in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the
8、 address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from eithe
9、r ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reservedBS ISO 7573:2008 ISO 757
10、3:2008(E) ISO 2008 All rights reserved iiiContents Page Foreword iv 1 Scope1 2 Normative references1 3 Terms and definitions .1 4 General .2 5 Parts lists arrangement.2 5.1 Position.2 5.2 Data fields for parts lists.3 Annex A (informative) Examples of layout arrangements for parts lists 5 Bibliograp
11、hy8 BS ISO 7573:2008 ISO 7573:2008(E) iv ISO 2008 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technic
12、al committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely wi
13、th the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft Inte
14、rnational Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document ma
15、y be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 7573 was prepared by Technical Committee ISO/TC 10, Technical product documentation, Subcommittee SC 1, Basic conventions. This second edition cancels and replaces the first editio
16、n (ISO 7573:1983), which has been technically revised. BS ISO 7573:2008 INTERNATIONAL STANDARD ISO 7573:2008(E) ISO 2008 All rights reserved 1Technical product documentation Parts lists 1 Scope This International Standard provides minimum requirements for parts lists to provide necessary information
17、, e.g. for the production, procurement or maintenance of the parts. This International Standard covers manual as well as computer-generated parts lists. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the ed
18、ition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 128-20, Technical drawings General principles of presentation Part 20: Basic conventions for lines ISO 5457, Technical product documentation Sizes and layout of drawing
19、sheets 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 assembly number of component parts fitted together to perform a specific function 3.2 part reference identification of component parts of assemblies and/or the identification of individua
20、l parts on the same drawing NOTE 1 Adapted from ISO 6433:1981. NOTE 2 Part references are document-based, as opposed to reference designations, which are structure-based. Identical parts on a drawing are required to have the same part reference, preferably a number (according to ISO 6433), while eac
21、h occurrence of an object in a structure is required to have a unique reference designation (according to IEC 61346-1). 3.3 quantity total number of the particular part(s) necessary for one specific assembly NOTE Quantity can express the number of parts or the amount of material. 3.4 unit entity ado
22、pted as the basis or standard of measurement NOTE The SI units, including their multiple prefixes, should be used. BS ISO 7573:2008 ISO 7573:2008(E) 2 ISO 2008 All rights reserved3.5 reference designation identifier of a specific object with respect to the system of which the object is a constituent
23、, based on one or more aspects of that system IEC 61346-1 3.6 part number unique identification of a part for a particular organization 3.7 part name text designation of a part 3.8 technical data designation indication by words or signs 3.9 remarks additional comments regarding the part 4 General Pa
24、rts lists specify all constituents of an assembled part by part reference number, quantity, part number, technical data, etc. The association between the part on a parts list and its graphical representation on the drawing is given by an identification reference. This reference can be given by a par
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO75732008EN_5566TECHNICALPRODUCTDOCUMENTATIONPARTSLISTS 技术 产品 文件 部件 清单 PDF

链接地址:http://www.mydoc123.com/p-391381.html