ANSI ASTM D2665-2014 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain Waste and Vent Pipe and Fittings.pdf
《ANSI ASTM D2665-2014 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain Waste and Vent Pipe and Fittings.pdf》由会员分享,可在线阅读,更多相关《ANSI ASTM D2665-2014 Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain Waste and Vent Pipe and Fittings.pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D2665 14 An American National StandardStandard Specification forPoly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and VentPipe and Fittings1This standard is issued under the fixed designation D2665; the number immediately following the designation indicates the year oforiginal adoption o
2、r, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. S
3、cope*1.1 This specification covers requirements and test methodsfor materials, dimensions and tolerances, pipe stiffness, crushresistance, impact resistance, and solvent cement for poly(vinylchloride) plastic drain, waste, and vent pipe and fittings.Aformof marking is also included. Plastic which do
4、es not meet thematerial requirements specified in Section 5 is excluded.Installation procedures are given in the Appendix.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information
5、 onlyand are not considered standard.1.3 The text of this specification references notes, footnotes,and appendixes which provide explanatory material. Thesenotes and footnotes (excluding those in tables and figures) shallnot be considered as requirements of the specification.1.4 The following safety
6、 hazards caveat pertains only to thetest methods portion, Section 7, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety and healthpractices an
7、d determine the applicability of regulatory limita-tions prior to use.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1784 Specification for Rigid Poly(Vinyl Chloride) (PVC)Compounds and Chlori
8、nated Poly(Vinyl Chloride)(CPVC) CompoundsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsD2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD2444 Test Method for Determination of the Impact Resis-tance of T
9、hermoplastic Pipe and Fittings by Means of aTup (Falling Weight)D2564 Specification for Solvent Cements for Poly(VinylChloride) (PVC) Plastic Piping SystemsD3311 Specification for Drain, Waste, and Vent (DWV)Plastic Fittings PatternsF402 Practice for Safe Handling of Solvent Cements,Primers, and Cle
10、aners Used for Joining ThermoplasticPipe and FittingsF412 Terminology Relating to Plastic Piping SystemsF1498 Specification for Taper Pipe Threads 60 for Thermo-plastic Pipe and FittingsF1866 Specification for Poly (Vinyl Chloride) (PVC) PlasticSchedule 40 Drainage and DWV Fabricated FittingsF2135 S
11、pecification for Molded Drain, Waste, and Vent(DWV) Short-Pattern Plastic Fittings3. Terminology3.1 Definitions are in accordance with Terminology F412,and abbreviations are in accordance with Terminology D1600,unless otherwise specified.4. Significance and Use4.1 The requirements of this specificat
12、ion are intended toprovide pipe and fittings suitable for the drainage and ventingof sewage and certain other liquid wastes.NOTE 1Industrial waste disposal lines should be installed only withthe specific approval of the cognizant building code authority sincechemicals not commonly found in drains an
13、d sewers and temperatures inexcess of 180F (82.2C) may be encountered.NOTE 2This specification does not include requirements for pipe andfittings intended to be used to vent combustion gases.5. Materials5.1 Basic MaterialsThe pipe shall be made of virgin PVCcompounds meeting or exceeding the require
14、ments of Class1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.63 on DWV.Current edition approved May 1, 2014. Published June 2014. Originallyapproved in 1968. Last previous edition approved in 2012 as D
15、2665 12. DOI:10.1520/D2665-14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section a
16、ppears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States112454 as defined in Specification D1784. The fittings shall bemade of virgin PVC compounds meeting or exceeding therequirements of Class 12344 as define
17、d in SpecificationD1784, but with a tensile strength of not less than 6500 psi anda modulus of elasticity for not less than 380,000 psi. Theseplastics contain stabilizers, lubricants, and pigments.5.2 Rework MaterialThe manufacturer shall use only hisown clean pipe or fitting rework material, and th
18、e pipe orfittings produced shall meet all the requirements of thisspecification.5.3 Solvent CementThe solvent cement used to join pipeand fittings made to this specification shall meet the require-ments of Specification D2564.6. Requirements6.1 GeneralThe pipe and fittings shall be homogeneousthroug
19、hout and free of visible cracks, holes, foreign inclusions,or other injurious defects. The pipe shall be as uniform ascommercially practicable in color, opacity, density, and otherphysical properties.6.1.1 The requirements in this section are intended only foruse as quality control tests, not as sim
20、ulated service tests.6.2 Dimensions and Tolerances:6.2.1 MethodAll dimensions shall be determined in accor-dance with Test Method D2122.6.2.2 Dimensions:6.2.2.1 The outside diameter and wall thicknesses of pipeshall meet the requirements of Table 2. The pipe shall be ineither 10 or 20-ft (3.05 or 6.
21、1-m) lengths, unless otherwisespecified, with an allowable tolerance of +12, 0 in. (+13, 0mm).6.2.2.2 The patterns, dimensions, and laying lengths offittings, including adaptors, shall meet the requirements ofSpecification D3311 and Table 1.6.2.2.3 Reducer bushings of sizes 2 by 114 and 4 by 3 shall
22、be permitted to have the socket wall thickness and spigot wallthickness below the minimum requirements defined in Table 1,but not less than 0.098 in. (2.5 mm), provided the inner socketand outer spigot are reinforced by a minimum of four ribs. Thethickness of the supporting ribs shall not be less th
23、an 0.098 in.(2.5 mm).6.2.2.4 The patterns, dimensions, and laying lengths ofShort-Pattern fittings shall meet the requirements of Specifica-tion F2135.6.2.2.5 For all fittings having taper pipe threads, threadsshall conform to Specification F1498 and be gaged in accor-dance with 7.5. Fittings of nom
24、inal sizes not given in Speci-fication F1498 shall not have threads.6.2.2.6 Fabricated DWV fittings shall comply with Specifi-cation F1866.6.3 Pipe Stiffness, Deflection Load and Flattening:6.3.1 PipeThe minimum pipe stiffness at 5 % deflectionshall be in accordance with Table 3. The pipe shall defl
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ANSIASTMD26652014STANDARDSPECIFICATIONFORPOLYVINYLCHLORIDEPVCPLASTICDRAINWASTEANDVENTPIPEANDFITTINGSPDF

链接地址:http://www.mydoc123.com/p-432295.html