ARMY MIL-A-63117-1977 AMPLIFIER HYBRID RADIO FREQUENCY FOR XM122 FIRING DEVICE RECEIVER《XM122型点火装置接收器扬声器混合动力无线电频率》.pdf

《ARMY MIL-A-63117-1977 AMPLIFIER HYBRID RADIO FREQUENCY FOR XM122 FIRING DEVICE RECEIVER《XM122型点火装置接收器扬声器混合动力无线电频率》.pdf》由会员分享，可在线阅读，更多相关《ARMY MIL-A-63117-1977 AMPLIFIER HYBRID RADIO FREQUENCY FOR XM122 FIRING DEVICE RECEIVER《XM122型点火装置接收器扬声器混合动力无线电频率》.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-A-63117 (AR) 11 APRIL 1977 MILITARY SPECIFICATION AMPLIFIER, HYBRID, RADIO FREQUENCY FOR XN22 FIRING DEVICE RECEIVER This specification is approved for use by the U.S. Army Armament Research and Development Command, and is available for use by Departments and Agencies of the Department of Defens

2、e. 1.1 This specification contains requirements not normally covered by the drawings and provides quality assurance provisions for the fabrication of parts, assembly and packing of one type of hybrid radio frequency amplifier for the N22 firing device receiver . 2. APPLICABLE DOCUMENTS 2.1 Issues of

3、 documents.-The following documents of the issue in effect on date of inactivation for bids or request for proposals, form a part of this specification to the extent specified herein. SPECIFICATIONS MILITARY MIL-A-48078 - Ammunition, Standard Quality Assurance Provisions, General Specification For S

4、TANDARDS MILITARY MIL-STD-105 - Sampling Procedures and Tpbles For Inspection By Attributes MIL-STD-331 - Fuze and Fuze Components, Environmental and Performance Test For MIL-STD-810 - Environmental Test Methods MIL-STD-883 - Test Methods and Procedures For Microelectronics MIL-STD-1169- Packaging,

5、Packing and Marking for Shipment of Inert Ammunition ComDonents Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Picatinny Arsenal, Dover, New Jersey 07801 by using the self-addressed

6、Standard- ization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. I FSC: 13751 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-A-63L17 13 I 777770b 0344005 3 I MIL-A-63117 (AR) DHAWINGS U 8 ARMY AR

7、MAMENT RESEARCH AND DEVELOPPIENT COIIMAND 9278755 - U1 R.F. Amplifier, Hybrid (Copies of specifications, standards, drawings, and publications required by suppliers in connection with specific procurement fucntions should be obtained from the procuring activity or as directed by the contracting offi

8、cer. 3. RErQUIREMENTS 3.1 Material.-Materials shall be in accordance with the applicable drawings and specifications. 3.2 Components and assemblies.-The components and asembly shall comply with all requirements specified in drawing 9278755 and associated drawings and with all requirements specified

9、in applicable specifications and standards. 3.3 Vibration.-The module shall not show evidence of damage or failure when tested in accordance with 4.5.1. 3.4 Rough Handling.-The module shall not show evidence of damage or failure when tested in accordance with 4.5.2. 3.5 Humidity.-The module shall no

10、t show evidence of damage or f3ilure when tested as specified in 4.5.3. 3.6 Temperature Cycling.-The module shall withstand sud- den changes in temperature when tested as specified in 4.5.4. 3.7 Gross leak.-The module shall not shown evidence of leakage when tested as specified in 4.5.5. 3,8 Fine le

11、ak.-The module shall not show evidence of leakage when tested as specified in 4.5.6. 3.9 Electrical Performance Characteristics 3.9.1 Voltage gain.-The module voltage gain shall be eighteen and five tenths plus or minus one decibel (18.5 db 2 1 db) when tested as specified in 4.5.7.1 3.9.2 Noise fig

12、ure.-The overall noise figure shall be eight decibel (8 db) maximum when tested as specified in 4.5.7.2. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-* MIL-A-b31L7 13 7773906 034400b 5 W MIL-A-63117 (e) -. 3.9.3 Input impedance.-The input impeda

13、nce between pin numbers two and three (2 and 3) shall be thirty to fifty (30 to 50) ohms when tested as specified in 4.5.7.3. 3.9.4 Output impedance.-The output impedance between pins six and two (6 and 2) shall be twenty two picifarads (22 pfd) plus or minus five percent (+ 5%) when tested as speci

14、fied in 4.5.7.4. - 3.9.5 Bias voltage.-The module shall generate a voltage of one and forty hundreds plus or minus five hundreds volts direct current (1.40 + 0.05 VDC) when tested as specified in 4.5.7.5. exceed two milliamperes (2 ma) when tested as specified in 4.5.7.6. - 3.9.6 Current drain.-The

15、module current drain shall not 3.9.7 Voltage variations.-The module shall meet the require- ments of 3.9.1 through 3.9.6 when all referenced voltages are varied to the specified maximum and minimum limits as tested in 4.5.7.7. 3.9.8 Temperature variations.-The module shall meet the requirements of 3

16、.9.7 over the temperature range of minus thirty two degrees centigrade (-32OC) to plus sixty five degrees centi- grade (+65“F) when tested as specified in 4.5.7.8. 3.10 Rework or retest.-Any module failing to comply with all of the test requirements and undergoes rework or repair shall be tested as

17、specified in 4.5.10. 3.11 Test temperature.-Unless specified otherwise, all testing shall be performed at a temperature of twenty degrees centigrade plus ten degrees centigrade (20C 5 10C). 3.12 Data requirements.-Data shall be recorded and retained for all test required by this specification and as

18、 specified in 4.5.9. 3.13 Workmanship.-The module shall be free from dirt, chips, grease, flux, rust or other foreign matter that may impair proper functioning. The cleaning methods used shall not be injurious to any part or assembly nor shall the parts or assembly be con- taminated. 4. QUALITY ASSU

19、RANCE PROVISIONS 3 ,r I .; i : . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ MIL-A-63117 13 7999906 03Lt4007 7 m MIL-A-63117 (AR) 4.1 Responsibility for inspect3on ahd standard quality assurance prQVisiohs.-Unless otherwise specified herein or

20、in the contract, the provisions of MIL-A-48078 shall apply and are hereby made a part of this specification. 4.2 Classification of inspections.-The following types of inspection shall be conducted on this item: a. First article inspection. b. Quality conformance inspections. 4.3 First article inspec

21、tion 4.3.1 Submission.-The contract shall submit a first article sample as designated by the Contracting Officer for evaluation in accordance with provisions of 4.3.2. shall consist of twenty five (25) modules. Table I specified herein. The first article sample 4.3.2 Inspections to be performed.-See

22、 MIL-A-48078 and 4 I . - E , . - . : . _ . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-L, - MIL-A-631L7 13 m 7777706 03iiOO 7 m r * K w u s Ln : E a al O h k al A al P rl rl a3 m Provided by IHSNot for ResaleNo reproduction or networking permitte

23、d without license from IHS-,-,- HIL-A-631L7 13 m 7777906 0311007 O m MIL-A-63117 (AR) 4.3.3 Rejection. - See MIL-A-48078. 4.4 Quality Conformance Inspection 4.4.1 Inspection lot formation. - Inspection lots shall comply with the lot formation provisions of MIL-A-48078. 4.4.2 Examination. - See MIL-A

24、-47078. a. Sampling plans. - Unless otherwise specified in the classification of defects and Test Tables, sampling plans for major and minor defects shall be in accordance with MIL-STD-105, Inspection Level II. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license fr

25、om IHS-,-,-WM?A O00 tkk-?R=?AIK 000000 O00 000000 555 ririrl.4riri a al + k O ri a f bt C =-=-Y- - 1- .* Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-A-63117 13 m 7777906 03gLi011 7 m II. O 8 Provided by IHSNot for ResaleNo reproduction or n

26、etworking permitted without license from IHS-,-,-MIL-A-63117 13 m 7797706 03qY012 O MIL-A-63117 (AR) 4.4.4 Inspection equipment.-The inspection equipment required to perform the examinations, and tests prescribed herein is des- cribed in the Paragraph Reference Inspection Method column in the tables

27、 of paragraph 4.4.2.1. The contractor shall submit for approval inspection equipment designs in accordance with the terms of the contract. See Section 6 of MIL-A-48078 and 6.3 herein. 4.5 Test methods and procedures 4.5.1 Vibration.-The module shall be subjected to the vibration test requirements of

28、 Method 514, Procedure XI, Part I, vibration and Part 2, Bounce, Loose Cargo of MIL-STD-810, (Non-destructive test) . 4.5.2 Rough handling.-The module shall be subjected to the requirements of paragraph 5.3, Test No. 114 of MIL-STD-331 (Non- destructive test). 4.5.3 Humidity test.-The module shall b

29、e subjected to Pro- cedure I, Method 507 of MIL-STD-810 (Non-destructive test). 4.5.4 Temperature cycling.-The module shall be subjected to ten (10) temperature cycles, in accordance with Condition C, Method 1010 of MIL-STD-883 (Non-destructive test) . 4.5.5 Gross leak.-The module shall be subjected

30、 to the gross leakage requirements of Condition C, Method 1014 of MIL-STD-883. Any module failing to comply with all of the specified require- ments shall be classed defective (Non-destructive test). 4.5.6 Fine leak.-The module shall be subjected to the fine leakage requirements of Condition A, Meth

31、od 1014 of MIL-STD-883. Any module failing to comply with all of the specified require- ments shall be classed defective (Non-destructive test). 4.5.7 Electrical Performance Characteris tics 4.5.7.1 Voltage gain.-The module shall be measured for the specified voltage gain using Test Circuit No .1. T

32、est frequency specified voltage gain using Test Circuit No. 1. Test frequency minus one thousand hertz (25,500,000 Hz + 1000 Hz). The input shall be driven from a fifty (50) ohm souTce at minus forty five decibel (-45 dbm) maximum. Transformer, T1, shall be adjusted for maximum output. The F? output

33、 of the test circuit shall be terminated into fifty (50) ohms. Pin number four (4) shall have 9 r. i, . . . ._ - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-A-63117 (AR) an applied bias voltage of one and one hundred and fifty five thousands

34、plus or minus five thousands volts direct current (1.155 VDC + 0.005 VDC). Pin number eight (8) shall have an applied supply voltage of three and twenty five hundreds plus or minus twenty five hundreds (3.25 2 0.25) VDC. Pin number two (2) shall be grounded. Any module failing to comply with all of

35、the specified requirements shall be classed defective. (Non- destructive test). 4.5.7.2 Noise figure.-The module shall be tested for the specified noise level using Test Circuit No. 1. Test fre- quency shall be twenty five million five hundred thousand hertz plus or minus ten thousand hertz (25,500,

36、000 Hz + 10,000 Hz). Pin number four (4) shall have an applied bias voltage of one and one hundred and fifty five thousands plus or minus five thousands (1.155 VDC + 0.005 VDC). Pin number eight (8) shall have an applied supply voltage of three and twenty five hundreds plus or minus twenty five hund

37、reds (3.25 VDC + 0.25 VDC). Pin number two (2) shall be grounded. A noise figure meter having a fifty (50) ohm source impedance shall be connected to the RF input. A fifty (50) ohm load impedance shall be connected to the output of the test circuit. Any module failing to comply with all of the speci

38、fied requirements shall be classed defective. (Non-destructive test). 4.5.7.3 Input impedance.-The module shall be measured for the specified input impedance requirements using Test Cirucit No. 1. Pin two (2) of the module shall be internally connected to the case. Test frequency shall be twenty fiv

39、e million, five hundred thousand hertz plus or minus ten thousand hertz (25,500,000 Hz 5 10,000 Hz). Pin number four (4) shall have an applied bias voltage of one and one hundred and fifty five thousands plus or minus five thousands (1.155 VDC i- 0.005 VDC). Pin number eight (8) shall have an applie

40、d supply-voltage of three and twenty five hundreds plus or minus twenty five hundreds (3.25 VDC + 0.25 VDC). A vector impedance meter shall be connected at the RF Tnput to read the module characteristics. Any module failing to comply with all of the specified requirements shall be classed defective

41、(Non-destructive test) . 4.5.7.4 Output impedance.-The module shall be measured for the specified requirements using Test Circuit No. 2. Test fre- quency shall be twenty five million five hundred thousand hertz plus or minus twenty thousand hertz (25,500,000 Hz 5 50,000 Hz). 10 Provided by IHSNot fo

42、r ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-A-63117 13 R 7779706 034401Y 4 MIL-A-63117 (AR) Pin number four (4) shall have an applied bias voltage of one and one hundred and fifty five thousands plus or minus five thousands. (1.155 VDC + 0.005 VE). Pin number ei

43、ght (8) shall have an applied supply voltage of three and twenty five hundreds plus or minus twnety five hundreds (3.25 VDC + 0.25 VDC). A reactance meter shall be used to read the module characteristics. Any r?iodule failing to comply with all of the specified require- ments shall be classed defect

44、ive (Non-destructive test). 4.5.7.5 Bias voltage.-The module shall meet the specified requirements when using Test Circuit No. 3. Measurements shall be performed with a twelve thousand plus or minus five hundred (12,000 + 500) ohm load between pin five (5) and ground. Pin one (1) zhall have an appli

45、ed voltage of nine to thirteen and five tenths (9.0 VDC to 13.5 VDC). Pin number eight (8) shall have an applied voltage of three and twenty five hundreds plus or minus twenty five hundreds (3.25 VDC + 0.25 VDC). Pin five (5) shall not generate an output when pin one (1) is held at zero. (O VDC. Any

46、 module failing to comply with all of the specified requirements shall be classed defective (Non-destructive test) . 4.5.7.6 Current drain.-The module shall be tested for the specified requirements using Test Circuit No. 4. Measure- ments shall be made on pin number eight (8) using approved equipmen

47、t. Pin number four (4) shall have an applied bias input voltage of one and one hundred and fifty five plus or minus five thousands (1.155 VDC + 0.005 VDC). Pin number eight (8) shall have an applied voltage of three and twenty five hundreds plus or minus twenty five hundreds (3.25 VDC + 0.25 VDC). o

48、hm resistive load shall be connected between pins five and Cwo (5 and 2). Pin number one (1) shall have an applied voltage of nine to thirteen and five tenths (9 .O to 13.5) VDC. Any module failing to comply with all of the specified requirements shall be classed defective (Non-destructive test). A

49、twelve thousand plus or minus five hundred (12,000+ 500) 4.5.7.7 Voltage variations.-The module shall be tested for the specified requirements using Test Circuits 1 through 4 as applicable for the respective test. Voltages shall be varied to the limits in previous test of 4.5.7.1-4.5.2.6. Any module failing to comply with all of the specified requirements sh