ARMY MIL-L-46811 B-1990 LUBRICATION OF GROUND HANDLING LAUNCHING AND CONTROL EQUIPMENT FOR GUIDED MISSILES《指导导弹地面处理和发射控制设备用润滑油》.pdf
《ARMY MIL-L-46811 B-1990 LUBRICATION OF GROUND HANDLING LAUNCHING AND CONTROL EQUIPMENT FOR GUIDED MISSILES《指导导弹地面处理和发射控制设备用润滑油》.pdf》由会员分享,可在线阅读,更多相关《ARMY MIL-L-46811 B-1990 LUBRICATION OF GROUND HANDLING LAUNCHING AND CONTROL EQUIPMENT FOR GUIDED MISSILES《指导导弹地面处理和发射控制设备用润滑油》.pdf(8页珍藏版)》请在麦多课文档分享上搜索。
1、I INCH - POUND 1 MIL-L-46811B (MI) 10 September 1990 SUPERSEDING MIL-L-4 6811A (MI) 27 October 1969 MILITARY SPECIFICATION LUBRICATION OF GROUND HANDLING, LAUNCHING AND CONTROL EQUIPMENT FOR GUIDED MISSILES This specification is approved for use by the U.S. Army Missile Command, Department of the Ar
2、my, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This process specification covers the requirements for lubrication of ground handling, launching, and control equipment for guided missiles in the course of manufacture and assembly. e 2. A
3、PPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standard, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of
4、the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). - - Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commande
5、r, US Army Missile Command, ATTN: AMSMI-RD-SE-TD- ST, Redstone Arsenal, AL 35898-5270 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. FSC 1440 AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is
6、 e unlimited. Licensed by Information Handling ServicesMIL-L-LIb8LLB 14 W 777770b OLI47732 13 II r I MIL-L-46811B (MI) SPECIFICATIONS FEDERAL TT-S-1732 MILITARY MIL-L-2104 MIL-G-4343 MIL-H-5606 MIL-G-10924 MIL-C-16173 MIL-G-23827 MIL-L-46167 Sealing Compound; Pipe Joint and Thread, Lead Free General
7、 Purpose Lubricating Oil, Internal Combustion Engine, Tactical Service (Metric) Grease, Pneumatic System Hydraulic Fluid, Petroleum Base: Aircraft, Missile, and Ordnance Grease, Automotive and Artillery Corrosion Preventive Compound, Solvent Cutback, Cold Application Grease, Aircraft and Instrument,
8、 Gear and Actuator Screw, NATO Code Number G- 3 5 4 , Metric Lubricating Oil, Internal Combustion Engine, Arctic (Unless otherwise indicated, copies of the federal and military specifications, standards, and handbooks are available from the Naval Publications and Forms Center, Standardization Docume
9、nts Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094. 2.2 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document shall take precedence. Nothing in this document, however, supersedes applicable
10、laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Materials. The lubricants shall successfully meet the material requirements of the applicable specification specified herein. 3.2 Equipment. Lubricant guns, cans, brushes, storage containers, and allied equipment
11、 shall be kept clean and free from contaminants. 3.3 Surface preparation, All dirt, moisture, or other contamination on surfaces to be lubricated shall be removed prior to the application of the lubricant. 3.3.1 Cleaning. Prior to the application of lubricants or preservatives, assemblies and compon
12、ents shall be free of corrosion and residues foreign to the item. Critical functioning or close tolerance surfaces shall be cleaned by an appropriate process to insure removal of corrosion. If practical, internal parts of complex assemblies shall be cleaned prior to assembly, and precautions taken t
13、o avoid contamination O thereafter. 3.4 Application. Where practical, components shall be operated while being lubricated to assure full coverage of bearing surfaces. Lubricants 2 Licensed by Information Handling ServicesI MIL-L-46811B (MI) shall be applied to threaded parts when necessary to preven
14、t seizure or galling during assembly or installation of such parts. 3.4.1 Fluid line fittings. Lubricants, where required, shall be applied sparingly to the male threads. Lubricant shall not be applied on the nose of a fitting, the first 1.5 tuns of thread from the nose, OE the female threads. Lubri
15、cant shall not be allowed to enter the fluid system. 3.4.2 Acid oxidizer systems. The lubricant used on the acid oxidizer system and in elements of pneumatic systems associated therewith shall be one of the polymers of trifluorovinyl chloride as specified. WARNING I Oil or grease shall not be applie
16、d to fittings of an oxygen container, nor allowed tO come in contact with an oxygen system. 3.4.3 Fuel systems. When lubricating any associated components of the fuel systems, a lubricant conforming to MIL-G-4343 or TT-S-1732 shall be used. 3.4.4 Compressed air system. Any lubricant used shall confo
17、rm to MIL- G-4343. 3.4.5 Hydraulic fluid system. The lubricant used shall conform to MIL- H-5606 as applicable for the system. 3.4.6 Other threaded parts. Lubricants where required, shall be applied on the male threads only. adjustment, lubricant conforming to MIL-G-10924 shall be used. Where loadin
18、g or occasional adjustment is required, lubricant conforming to TT-S-1732 shall be used. For sub-zero applications, lubricant conforming to MIL-L-46167 shall be used. On threads requiring movement or frequent 3.5 Grease fittings. Grease shall be forced into fittings until grease The extruded surplus
19、 grease-shall be wiped off with lint free is extruded. wipers. 3.6 Friction bearings. Friction bearings (bushings) of steel or brass shall be lubricated with grease conforming to MIL-G-10924 or oil conforming to MIL-L-2104. 3.6.1 Antifriction bearings. Antiriction beaxings (with rolling components)
20、shall be lubricated using grease conforming to MIL-G-23827. 3.7 O-rings. Hydraulic system O-rings shall be lubricated by the dip and drain method prior to installation. applications and contacts shall be used on the O-rings. Specified lubricants for the various 3.8 Specific parts and assemblies. The
21、 equipment and components assembled in the course of manufacture ob rebuild shall be lubricated in accordance with tables I and II. 3 Licensed by Information Handling ServicesMIL-L-4bLLB 14 U 777770b 0447734 L MIL-L-46811B (MI) 3.9 Workmanship, Workmanship shall be such as to insure compliance with
22、the requirements of this specification and shall be of good quality. TABLE I. LubEication list for launchinq equipment. ITEM Running gear units, wheel bearings-hand pack with grease. Hand brake levers, latches, catches, and shaft-turning points - oil lightly, remove excess Base leg assembly attach p
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ARMYMILL46811B1990LUBRICATIONOFGROUNDHANDLINGLAUNCHINGANDCONTROLEQUIPMENTFORGUIDEDMISSILES 指导 导弹 地面 处理

链接地址:http://www.mydoc123.com/p-445577.html