BS 7448-1-1991 Fracture mechanics toughness tests - Method for determination of KIc critical CTOD and critical J values of metallic materials《断裂结构韧性试验 金属材料的KIc临界CTOD和临界J值的测定方法》.pdf
《BS 7448-1-1991 Fracture mechanics toughness tests - Method for determination of KIc critical CTOD and critical J values of metallic materials《断裂结构韧性试验 金属材料的KIc临界CTOD和临界J值的测定方法》.pdf》由会员分享,可在线阅读,更多相关《BS 7448-1-1991 Fracture mechanics toughness tests - Method for determination of KIc critical CTOD and critical J values of metallic materials《断裂结构韧性试验 金属材料的KIc临界CTOD和临界J值的测定方法》.pdf(48页珍藏版)》请在麦多课文档分享上搜索。
1、BRITISH STANDARD BS 7448-1:1991 Incorporating Amendment No. 1 and Corrigendum No. 1 Fracture mechanics toughness tests Part 1: Method for determination of K Ic , critical CTOD and critical J values of metallic materials ICS 77.040.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT
2、 LAWBS 7448-1:1991 This British Standard, having been prepared under the direction of the Iron and Steel and the Non-ferrous Metals Standards Policy Committees, was published under the authority of the Standards Board and comes into effect on 20 December 1991 BSI 27 February 2002 The following BSI r
3、eferences relate to the work on this standard: Committee reference ISM/NFM/4 Draft for comment 90/41825 DC ISBN 0 580 20037 X Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Iron and Steel Standards Policy Committee (ISM/-) and the Non-f
4、errous Metals Standards Policy Committee (NFM/-) to Technical Committee ISM/NFM/4, upon which the following bodies were represented: Aluminium Federation British Gas plc British Non-ferrous Metals Federation British Railways Board British Steel Industry Copper Development Association Department of T
5、rade and Industry (National Engineering Laboratory) Department of Trade and Industry (National Measurement Accreditation Service) Department of Trade and Industry (National Physical Laboratory) ERA Technology Ltd. GAMBICA (BEAMA Ltd.) Ministry of Defence Society of British Aerospace Companies Limite
6、d Welding Institute The following bodies were also represented in the drafting of the standard, through subcommittees and panels: BCIRA BEAMA Ltd. Electricity Supply Industry in United Kingdom Lloyds Register of Shipping Steel Casting Research and Trade Association United Kingdom Atomic Energy Autho
7、rity Amendments issued since publication Amd. No. Date Comments 10543 August 1999 12018 Corrigendum No. 1 27 February 2002 Corrections to Figure 10, Table 2 and 8.2.BS 7448-1:1991 BSI 27 February 2002 i Contents Page Committees responsible Inside front cover Foreword iii 1S c o p e 1 2 Definitions 1
8、 3 Symbols and designations 2 4 Principle 4 5 Test specimens 4 6 Specimen preparation and fatigue precracking 9 7 Test equipment 18 8 Test procedure 22 9 Analysis of test data 25 10 Validity check lists 32 11 Test report 33 Appendix A Bibliography 34 Appendix B Crack plane identification 34 Appendix
9、 C Measurement of load-line displacement (q) in a three point bend test 37 Figure 1 Flow chart for choice of fracture toughness parameter, specimen design and displacement measurement 5 Figure 2 Proportional dimensions and tolerances for a rectangular section bend specimen 6 Figure 3 Proportional di
10、mensions and tolerances for a square section bend specimen 6 Figure 4 Proportional dimensions and tolerances for a straight notch compact specimen 7 Figure 5 Proportional dimensions and tolerances for a stepped notch compact specimen 8 Figure 6 Acceptable fatigue crack starter notches and fatigue cr
11、ack configurations 10 Figure 7 Chevron notch 11 Figure 8 Outward pointing knife edges and corresponding notch geometries 12 Figure 9 Inward pointing knife edges and corresponding notch geometries 13 Figure 10 Fixture for three point bend tests 14 Figure 11 Typical design of clevis for applying a ten
12、sile force to a compact specimen using a circular hole in the clevis, and a pin having a diameter of 0.24W 0.005W, 0.015W 20 Figure 12 Typical design of clevis for applying a tensile force to a compact specimen using a hole with a flat in the clevis, and a pin having a diamter of 0.24W +0.000 W, 0.0
13、05W 21 Figure 13 Characteristic type of force versus displacement records in fracture tests 23 Figure 14 Assessment of pop-in behaviour 26 Figure 15 Definition of F Q(for the determination of K Q )2 7 Figure 16 Definition of V p(for the determination of CTOD) 29 Figure 17 Definition of U p(for the d
14、etermination of J)3 1 Figure 18 Basic fracture plane identification: rectangular section 35 Figure 19 Basic fracture plane identification: cylindrical sections 36 Figure 20 Non-basic fracture plane identification 36BS 7448-1:1991 ii BSI 27 February 2002 Page Figure 21 Principle of the “comparator” b
15、ar measurement 37 Figure 22 Displacements associated with three point bend specimens 38 Figure 23 Simultaneous determination of extraneous displacements ( 1 + 2 )3 8 Figure 24 Location of two notch opening displacement measurements (V 1and V 2 ) for the determination of load-line displacement 39 Tab
16、le 1 Dimensions of specimens that may lead to valid K Icvalues 9 Table 2 Values of for three point bend specimens 16 Table 3 Values of for compact specimens 18 Publication(s) referred to 40 f a o W - - f a o W - - BS 7448-1:1991 BSI 27 February 2002 iii Foreword This part of BS 7448 has been publish
17、ed under the direction of the Iron and Steel and the Non-ferrous Metals Standards Policy Committees. It gives a method for determining plane strain fracture toughness (K Ic ), critical crack tip opening displacement (CTOD) 1)and critical J fracture toughness values for metallic materials under displ
18、acement controlled monotonic loading at quasistatic rates. This part of BS 7448 combines and extends the methods for determining K Icvalues, given in BS 5447, and the method for determining crack opening displacement (COD), given in BS 5762:1979, BS 5447:1977 and BS 5762:1979 are withdrawn. Determin
19、ation of K Icfor materials and conditions for which it is appropriate to determine fracture toughness in terms of K Icalone are covered in BS EN ISO 12737. General determinations of fracture toughness, where the fracture behaviour determines the relevant fracture parameters (e.g. K Ic , CTOD or J) a
20、re covered in the procedures in this part of BS 7448, BS 7448-2 and BS 7448-4. The other three parts of BS 7448 are as follows: Part 2: Method for determination of K Ic , critical CTOD or J values of welds in metallic materials; Part 3: Method for determination of dynamic toughness 2) ; Part 4: Meth
21、od for determination of fracture resistance curves and initiation values for stable crack extension in metallic materials. It has been assumed in the drafting of this standard that the execution of its provisions is entrusted to appropriately qualified and experienced people. Safety note. It is impo
22、rtant to note that tests of the type described involve the use of large forces, and may involve the rapid movement of machine parts and fractured test specimens. Therefore it is important to consider the safety of machine operators. A British Standard does not purport to include all the necessary pr
23、ovisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i to iv, pages 1 to 40,
24、 an inside back cover and a back cover. The BSI copyright notice displayed throughout this document indicates when the document was last issued. 1) In this British Standard the term CTOD, which refers to crack tip opening displacement, is synonymous with the term COD in BS 5762. 2) In preparation.iv
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BS744811991FRACTUREMECHANICSTOUGHNESSTESTSMETHODFORDETERMINATIONOFKICCRITICALCTODANDCRITICALJVALUESOFMETALLICMATERIALS

链接地址:http://www.mydoc123.com/p-546810.html