1、BS ISO16853:2010ICS 59.120.10NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDTextile machinery Sliver cans,rectangular Maindimensions andtolerancesThis British Standardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 28 February20
2、10. BSI 2010ISBN 978 0 580 64578 5Amendments/corrigenda issued since publicationDate CommentsBS ISO 16853:2010National forewordThis British Standard is the UK implementation of ISO 16853:2010.The UK participation in its preparation was entrusted to TechnicalCommittee TCI/33, Textile machinery.A list
3、 of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obl
4、igations.BS ISO 16853:2010Reference numberISO 16853:2010(E)ISO 2010INTERNATIONAL STANDARD ISO16853Second edition2010-01-15Textile machinery Sliver cans, rectangular Main dimensions and tolerances Matriel pour lindustrie textile Pots pour rubans, rectangulaires Dimensions principales et tolrances BS
5、ISO 16853:2010ISO 16853:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the edi
6、ting. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be
7、 found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at
8、 the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from e
9、ither ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedBS ISO 16853:2010ISO
10、 16853:2010(E) ISO 2010 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each me
11、mber body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International E
12、lectrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards ad
13、opted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of pa
14、tent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16853 was prepared by Technical Committee ISO/TC 72, Textile machinery and accessories, Subcommittee SC 1, Spinning preparatory, spinning, twisting and winding machinery and accessories. This second edi
15、tion cancels and replaces the first edition (ISO 16853:2003), which has been technically revised. BS ISO 16853:2010BS ISO 16853:2010INTERNATIONAL STANDARD ISO 16853:2010(E) ISO 2010 All rights reserved 1Textile machinery Sliver cans, rectangular Main dimensions and tolerances 1 Scope This Internatio
16、nal Standard specifies the main dimensions, with tolerances, of rectangular sliver cans used in the textile industry. It also gives information about the right-angle position of cans according to ISO 1101. 2 Normative references The following referenced documents are indispensable for the applicatio
17、n of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1101, Geometrical Product Specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and
18、 run-out 3 Symbols and specifications The symbols and specifications shall be the following: b1outer width of the can b2inner width of the can h1outer height of the can l1outer length of the can l1up to 920 mm l2= l1 20 mm b2= b1 20 mm l1greater than 920 mm l2= l1 30 mm b2= b1 30 mm l2inner length o
19、f the can NOTE The stability of the can requires a greater top rim of can for greater dimensions of sliver cans. It is known that this inevitably results in smaller inner dimensions. BS ISO 16853:2010ISO 16853:2010(E) 2 ISO 2010 All rights reserved4 Main dimensions These shall be as specified in Tab
20、le 1 and Figure 1. NOTE Squareness tolerance is in conformity with ISO 1101. Figure 1 Sliver cans BS ISO 16853:2010ISO 16853:2010(E) ISO 2010 All rights reserved 3Table 1 Main dimensions of rectangular sliver cans Dimensions in millimetres l1a 3 l2b105b2h1c 5 215 195 1 040 1 070 1 100 1 200 220b200b
21、1 040 1 070 1 100 1 200 235b215b1 040 1 070 1 100 1 200 920 900 250b230b1 040 1 070 1 100 1 200 a Outer lengths l1greater than 920 mm shall be in increments of 100 mm. b Preferred dimensions. c Heights h1greater than 1 200 mm shall be in increments of 100 mm.5 Designation The designation for orderin
22、g a rectangular sliver can shall include the following information: a) a reference to this International Standard, i.e. ISO 16853:2009; b) the inner length, l2; c) the inner width, b2; d) the outer height, h1. EXAMPLE Rectangular sliver can corresponding to Figure 1 and Table 1, with an inner length
23、 l2= 900 mm and inner width b2= 215 mm and with an outer height h1= 1 070 mm: Rectangular sliver can ISO 16853 900 215 1 070 BS ISO 16853:2010ISO 16853:2010(E) ICS 59.120.10 Price based on 3 pages ISO 2010 All rights reserved BS ISO 16853:2010This page has been intentionally left blank BS ISO16853:2
24、010BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It
25、 is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if a
26、nyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating servic
27、e called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy
28、directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide ran
29、ge of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electronic information services are also available whichgive details on all its products and services. Contact Information Centre. Tel:+44 (0)20 8996 7111 Fa
30、x: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developmentsand receive substantial discounts on the purchase price of standards. For detailsof these and other benefits contact Membership Administration. Tel: +44 (0)208996 7002 Fax: +44 (0)20 8996 7001 Ema
31、il: Information regarding online access to British Standards via British StandardsOnline can be found at http:/ information about BSI is available on the BSI website at http:/CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in theUK, of the publications of the inter
32、national standardization bodies. Except aspermitted under the Copyright, Designs and Patents Act 1988 no extract maybe reproduced, stored in a retrieval system or transmitted in any form or by anymeans electronic, photocopying, recording or otherwise without prior writtenpermission from BSI.This doe
33、s not preclude the free use, in the course of implementing the standard,of necessary details such as symbols, and size, type or grade designations. Ifthese details are to be used for any other purpose than implementation then theprior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright and Licensing Manager.Tel: +44 (0)20 8996 7070 Email:
