BS ISO 19892-2011 Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of joints to pressure cycling《塑料管道系统 热塑性塑料管和冷热水配件 .pdf
《BS ISO 19892-2011 Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of joints to pressure cycling《塑料管道系统 热塑性塑料管和冷热水配件 .pdf》由会员分享,可在线阅读,更多相关《BS ISO 19892-2011 Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of joints to pressure cycling《塑料管道系统 热塑性塑料管和冷热水配件 .pdf(14页珍藏版)》请在麦多课文档分享上搜索。
1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 19892:2011Plastics piping systems Thermoplastics pipes andfittings for hot and coldwater Test method for theresistance of joints to pressurecyclingBS ISO 19892:2011 BRITIS
2、H STANDARDNational forewordThis British Standard is the UK implementation of ISO 19892:2011. The UK participation in its preparation was entrusted to TechnicalCommittee PRI/88/4, Test Methods - Plastic Piping.A list of organizations represented on this committee can be obtained on request to its sec
3、retary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. BSI 2011 ISBN 978 0 580 64382 8 ICS 23.040.60; 83.080.20 Compliance with a British Standard cannot confer immunity from legal obligations.This British St
4、andard was published under the authority of the Standards Policy and Strategy Committee on 30 November2011.Amendments issued since publicationDate T e x t a f f e c t e dBS ISO 19892:2011Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance o
5、f joints to pressure cyclingSystmes de canalisations en plastiques Tubes en matires thermoplastiques et raccords pour leau chaude et froide Mthode dessai de la rsistance des assemblages aux cycles de pression ISO 2011Reference numberISO 19892:2011(E)First edition2011-11-01ISO19892INTERNATIONAL STAND
6、ARDBS ISO 19892:2011ISO 19892:2011(E)COPYRIGHT PROTECTED DOCUMENT ISO 2011All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writ
7、ing from either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in Switzerlandii ISO 2011 All rights reservedBS ISO 19892:2011F
8、orewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a tec
9、hnical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters o
10、f electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to
11、 the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for i
12、dentifying any or all such patent rights.ISO 19892 was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 5, General properties of pipes, fittings and valves of plastic materials and their accessories Test methods and basic sp
13、ecifications .ISO 19892:2011(E) ISO 2011 All rights reserved iiiBS ISO 19892:2011BS ISO 19892:2011INTERNATIONAL STANDARD ISO 19892:2011(E)Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of joints to pressure cycling1 ScopeThis Internati
14、onal Standard specifies a method for testing the resistance of joints to pressure cycling. It is applicable to piping systems based on thermoplastics pipes intended to be used in hot and cold water applications.2 PrincipleAn assembly of pipes and fittings is subjected to water pressure cycling betwe
15、en two positive pressure limits, while being maintained at a specified temperature and inspected for leakage.NOTE It is assumed that the following test parameters are set by the reference standard (i.e. the standard making reference to this International Standard), as applicable (see Clause 4):a) th
16、e test temperature;b) the number of test pieces;c) the test pressure limits;d) the duration of one cycle;e) the number of cycles.3 Apparatus3.1 Pressurizing device, capable of applying and regulating the water pressure in the test piece in a sinusoidal or trapezoidal form between pressure limits as
17、specified in the reference standard.3.2 Pressure measurement device, capable of measuring the water pressure in the test piece to an accuracy of 5 %. The device measurement shall be capable of producing a record of the sinusoidal or trapezoidal wave form.3.3 Test chamber, capable of maintaining the
18、specified test temperature (see Clause 4) to an accuracy of 2 C.3.4 Thermometer(s), capable of checking conformity to the specified test temperature (see 3.3).3.5 End-sealing device, of appropriate size and sealing method for sealing the non-joined end of the test piece. The device shall be restrain
19、ed in a manner which does not exert longitudinal forces on the joints.A typical test arrangement is shown in Figure 1. ISO 2011 All rights reserved 1BS ISO 19892:2011Key1 temperature controlled test chamber2 test assemblies3 water4 air5 pressure converter6 compressed air cylinder7 valve8 electric co
20、ntrolFigure 1 Schematic test arrangement4 Test parametersUnless specified otherwise in the reference standard, the test parameters given in Table 1 shall apply.Table 1 Test parametersParameter ValueNumber of test pieces 3Conditioning and test temperature (23 2) CTest pressure limits Shall conform to
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO198922011PLASTICSPIPINGSYSTEMSTHERMOPLASTICSPIPESANDFITTINGSFORHOTANDCOLDWATERTESTMETHODFORTHERESISTANCEOFJOINTSTOPRESSURECYCLING

链接地址:http://www.mydoc123.com/p-586015.html