1、 5(ISO 8528-5:1993, IDT) , ()INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION(ISC) ISO8528-52011, - 1.092 . - 1.22009 . , . -, , , 1 - ()2 (-)3 , (- 29 2011 . 40) : ( 3166) 00497 ( 3166) 00497 BYKZKGRUTJUZ 4 13 2011 . 1163- ISO 8528-52011 1 2013 .5 ISO 8528-5:1993 Reciprocatingint
2、ernal combustion engine driven alternating current generating sets Part 5: Generating sets ( . 5. ). - . (IDT). 8528-520056 , - . () . - , , 2013 -, II ISO 8528-520111 12 13 24 45 .86 97 .128 , .129 1310 1411 1512 1613 1914 , .2015 .22 () 25III ISO 8528-52011 , :ISO 8528-1:1993 1. , ISO 8528-2:1993
3、2. ISO 8528-3:1993 3. ISO 8528-4:1993 4. ISO 8528-5:1993 5. ISO 8528-6:1993 6. ISO8528-7:1993 7.ISO 8528-8:1995 8. . ISO 8528-9:1993 9. ISO 8528-10:1993 10. ISO 8528-11:1993 11. ISO 8528-12:1997 12. IV ISO 8528-52011 5Reciprocating internal combustion engine driven alternating current generating set
4、s. Part 5. Generating sets 201301011 - ( ), . . , , . , , , . , , ., , - , . , -, , , - .2 :ISO 3046-4:1978 Reciprocating internal combustion engines: Performances Part 4: Speed governing( . . 4. - )ISO 3046-5:1978 Reciprocating internal combustion engines; Performances Part 5: Torsionalvibrations (
5、 . . 5. )ISO 8528-1:1993 Reciprocating internal combustion engine driven alternating current generatingsets Part 1: Application, ratings and performance ( . 1. , )ISO 8528-2:1993 Reciprocating internal combustion engine driven alternating current generatingsets Part 2: Engines ( . 2. )1 ISO 8528-520
6、11 ISO 8528-3:1993 Reciprocating internal combustion engine driven alternating current generatingsets Part 3: Alternating current generators for generating sets ( - . 3. )ISO 8528-10:1993 Reciprocating internal combustion engine driven alternating current generatingsets Part 10: Measurement of airbo
7、rne noise by the enveloping surface method ( . 10. )IEC 60034-1:2004 Rotating electrical machines Part 1: Rating and performance ( - . 1. )3 :fd ( ) dynamic frequency (frequency deviation);fd,max (maximumtransientfrequencyrise);fd,min (maximumtransientfrequencydrop);fdo (operating frequency of overf
8、requencylimiting device);fds (setting frequency of overfrequencylimiting device);fi (no-load frequency);fi, r (rated no-load frequency);fmax (maximum permissible frequency);fr ( ) declared frequency (rated frequency);fi,max (maximum no-load frequency);fi,min (minimum no-load frequency);farb (frequen
9、cy at actual power);fov (overload frequency);fc218c217 (width of frequency oscillation);Ik (sustained short-circuit current);t (time);ta (total stopping time);tb (load pick-up readiness time);t (off-load run-on time);td (run-down time);t (load pick-up time);tf, de (frequency recovery time after load
10、decrease);tf, in (frequency recovery time after loadincrease);tg (total run-up-time);th (run-up time);ti (on-load run-on time);tp (start preparation time);ts (load switching time);2 ISO 8528-52011tu (interruption time);tU (voltage recovery time);tU, de (voltage recovery time after loaddecrease);tU,
11、in (voltage recovery time after loadincrease);tv (start delay time);tz (cranking time);t0 (pre-lubricating time);vf (rate of change of frequency setting);vU (rate of change of voltage setting);Us, do (downward adjustable voltage);Us, up (upward adjustable voltage);Ur (rated voltage);Urec (recovery v
12、oltage);Us (set voltage);Ust,max (maximumsteady-state voltage deviation);Ust,min (minimumsteady-state voltage deviation);U0 (no-load voltage);Udyn,max (maximum upward transient voltage on load in crease);Udyn,min (minimum downward transient voltage on load in crease);Umax, s (maximumpeak value ofset
13、 voltage);Umin, s (minimum peak value ofset voltage);Umean, s - (average value of the maximum and minimum peak value ofset voltage);Umod, s (voltage modulation);Umod, s,max (maximumpeakofvoltagemodulation);Umod, s,min (minimum peak of voltage modulation);U (width of voltage oscillation);c68fneg (dow
14、nward frequencydeviation from linear curve);c68fpos (up ward frequencydeviation from linear curve);c68f (steady-state frequency tolerance band);c68fc (frequency deviation from a linear curve);c68fs (range of frequency setting);c68fs, do (downward range of frequency setting);c68fs, up (upward range o
15、f frequency setting);c68U (steady-state voltage tolerance band);3 ISO 8528-52011c68Us (range of voltage setting);c68Us, do (downward range of voltage setting);c68Us, up (upward range of voltage setting);c68c100fst - (frequency/power characteristic deviation);c97U (related steady-state voltage tolera
16、nce band);c97f (related frequency tolerance band);c98f (steady-state frequency band);c100fd ( ) (transient frequency difference (frominitial frequency);c100Udyn (transient voltage deviation);c100fdyn ( ) transient frequencydeviation (from rated frequency);c100fs (related range of frequency setting);
17、c100fs, do (related downward range offrequency setting);c100fs, up (relatedupwardrangeoffrequencysetting);c100fst (frequency droop);c100QCC (grade of quadrature-current compensation droop);c100S (cyclic irregularity);c100flim (over-frequency setting ratio);c100Ust (steady state voltage deviation);c100Us (
