NFPA 1951 AMD 1-2013 Standard on Protective Ensembles for Technical Rescue Incidents (Effective Date 8 20 2013).pdf

1、 Tentative Interim Amendment NFPA1951Standard on Protective Ensembles for Technical Rescue Incidents2013 Edition Reference: Various TIA 13-1 (SC 13-8-21/TIA Log #1098) Pursuant to Section 5 of the NFPA Regulations Governing the Development of NFPA Standards, the National Fire Protection Association

2、has issued the following Tentative Interim Amendment to NFPA 1951, Standard on Protective Ensembles for Technical Rescue Incidents, 2013 edition. The TIA was processed by the Technical Committee on Special Operations Protective Clothing and Equipment and the Correlating Committee on Fire and Emergen

3、cy Services Protective Clothing and Equipment, and was issued by the Standards Council on August 1, 2013, with an effective date of August 20, 2013. A Tentative Interim Amendment is tentative because it has not been processed through the entire standards-making procedures. It is interim because it i

4、s effective only between editions of the standard. A TIA automatically becomes a public input of the proponent for the next edition of the standard; as such, it then is subject to all of the procedures of the standards-making process. 1. Revise 2.3.3 to read as follows: 2.3.3 ASTM F 2412, Standard T

5、est Method s for Foot Protection, 2011. 2. Add the two new paragraphs below to follow 6.1.3.3.3. Renumber existing paragraphs 6.1.3.3.4 and 6.1.3.3.5 as 6.1.3.3.6 and 6.1.3.3.7 respectively. Change Annex item A.6.1.3.3.5 to A.6.1.3.3.7. Change Table 6.1.3.3.5 to Table 6.1.3.3.7. 6.1.3.3.4 The locati

6、on of the wrist crease shall be determined by first placing the glove on a measurement board palm down and securing (locking) the fingertips down onto the board. 6.1.3.3.5 A 1 lb weight shall be attached to the end of the glove body or gauntlet glove interface component. The weight shall not be atta

7、ched to a knitted wristlet glove interface component. The weight shall be applied evenly across the glove. 3. Add the two new paragraphs below to follow 6.2.3.3.3. Renumber existing paragraphs 6.2.3.3.4, 6.2.3.3.5, 6.2.3.3.6, 6.2.3.3.7 and 6.2.3.3.8 as 6.2.3.3.6, 6.2.3.3.7, 6.2.3.3.8, 6.2.3.3.9 and

8、6.2.3.3.10 respectively. Change Annex item A.6.2.3.3.5 to A.6.2.3.3.7. 6.2.3.3.4 The location of the wrist crease shall be determined by first placing the glove on a measurement board palm down and securing (locking) the fingertips down onto the board. 6.2.3.3.5 A 1 lb weight shall be attached to th

9、e end of the glove body or gauntlet glove interface component. The weight shall not be attached to a knitted wristlet glove interface component. The weight shall be applied evenly across the glove. 4. Revise 7.1.3.5 to read as follows: 7.1.3.5 Gloves shall be tested for grip as specified in Section

10、8.29, Grip Test, and shall not have a drop of force of more than 30 percent in any 0.2 second interval. 5. Revise 7.1.4.5 to read as follows: 7.1.4.5 Footwear soles and heels shall be tested for abrasion resistance as specified in Section 8.34, Abrasion Resistance Test 3, and the relative volume los

11、s shall not be greater than 250 mm3(0.02 in.3). 6. Revise 7.2.3.5 to read as follows: 7.2.3.5 Gloves shall be tested for grip as specified in Section 8.29, Grip Test, and shall not have a drop of force of more than 30 percent in any 0.2 second interval. 7. Revise 7.2.4.5 to read as follows: 7.2.4.5

12、Footwear soles and heels shall be tested for abrasion resistance as specified in Section 8.34, Abrasion Resistance Test 3, and the relative volume loss shall not be greater than 250 mm3(0.02 in.3). 8. Revise 7.3.4.5 to read as follows: 7.3.4.5 Gloves shall be tested for grip as specified in Section

13、8.29, Grip Test, and shall not have a drop of force of more than 30 percent in any 0.2 second interval. 9. Revise 7.3.5.5 to read as follows: 7.3.5.5 Footwear soles and heels shall be tested for abrasion resistance as specified in Section 8.34, Abrasion Resistance Test 3, and the relative volume los

14、s shall not be greater than 250 mm3(0.02 in.3). 10. Revise 7.3.5.10 to read as follows: 7.3.5.10 Footwear shall be individually tested for flame resistance as specified in Section 8.32, Flame Resistance Test 4, and shall not have an afterflame of more than 5seconds, shall not melt or drip, and shall

15、 not exhibit any burn-through. 11. Revise 8.1.9.5 to read as follows: 8.1.9.5 The wash cycle procedure in Table 8.1.9.5 (a) through Table 8.1.9.5 (c) shall be followed. Add two tables 8.1.9.5 (b) and 8.1.9.5 (c) to follow existing Table 8.1.9.5. Renumber Table 8.1.9.5 as Table 8.1.9.5 (a). Table 8.1

16、.9.5 (b) Water Level for Whole Garments and CBRN Materials Operation Wash Cycle Procedure Low Water Level 1 cm (3/8) in.) High Water Level 1 cm (3/8 in.) Number of Garments cm in. cm in. 1 to 3 15 5.9 25.5 10 4 to 6 17.5 6.9 28 11 7 or more 20 7.9 30.5 12 Table 8.1.9.5 (c) Water Level for Gloves and

17、 Glove Pouches Operation Wash Cycle Procedure Low Water Level High Water Level + 1 cm + 1 cm (3/8 in) (3/8 in) cm in cm in Gloves 20 7.9 30.5 12Glove Pouches 20 7.9 30.5 12 12. Revise 8.1.9.14 to read as follows: 8.1.9.14 Gloves and glove pouches shall be tumbled for 60 minutes and shall be removed

18、immediately at the end of the drying cycle. At the conclusion of the final drying cycle, the gloves or glove pouches shall be permitted to be dried on a forced air nontumble drying mechanism operated at 10oC 2C (50o F 3F) above current room temperature until completely dry. 13. Revise 8.2.2.2 to rea

19、d as follows: 8.2.2.2 Samples shall be conditioned as specified in 8.2.8, 8.2.9, or 8.2.10, except CBRN garment and material samples shall be conditioned as specified in 8.1.9 followed by 8.1.2. 14. Revise 8.2.9.1 to read as follows: 8.2.9.1 Samples for conditioning shall be in the form of a pouch a

20、s described in 8.1.14. 15. Revise 8.4.2.2 to read as follows: 8.4.2.2 Samples shall be conditioned as specified in 8.1.2. Other samples shall be conditioned as specified in 8.1.3 followed by conditioning as specified in 8.1.2, except CBRN garment and material samples shall be conditioned as specifie

21、d in 8.1.9 followed by 8.1.2. 16. Revise 8.5.11.4 to read as follows: 8.5.11.4 Sample helmets shall be positioned according to the HPI as described in 8.1.132 on the thermal headform conforming to the dimensions in Figure 8.5.11.4. 17. Revise 8.5.2.2 to read as follows: 8.5.2.2 Samples shall be cond

22、itioned as specified in 8.1.3 followed by conditioning as specified in 8.1.2, except CBRN garment and material samples and glove samples shall be conditioned as specified in 8.1.9 followed by conditioning as specified in 8.1.2. 18. Revise the following subsections to read as follows: 8.7.2.2 Samples

23、 shall be conditioned as specified in 8.1.3 followed by conditioning as specified in 8.1.2, except CBRN garment and material samples shall be conditioned as specified in 8.1.9 followed by conditioning as specified in 8.1.2. 8.8.2.2 Samples shall be conditioned as specified in 8.1.3 followed by condi

24、tioning as specified in 8.1.2, except CBRN garment and material samples shall be conditioned as specified in 8.1.9 followed by conditioning as specified in 8.1.2. 8.9.2.2 Samples shall be conditioned as specified in 8.1.3 followed by conditioning as specified in 8.1.2, except CBRN garment and materi

25、al samples shall be conditioned as specified in 8.1.9 followed by conditioning as specified in 8.1.2. 19. Revise 8.11.7.1 to read as follows: 8.11.7.1 Specimens shall be representative of the glove body composite construction at the glove areas A-P, B-P, D-P, E-P, F-P, G-P, H-P, I-P, A-B, B-B, D-B,

26、E-B, F-B, G-B, H-B, I-B as described in 8.1.143 and shall not include seams. Samples and specimens shall be permitted to be materials representative of those used in the construction of the glove. 20. Revise 8.13.2.2 and 8.16.2.2 to read as follows: 8.13.2.2 Samples shall be conditioned as specified

27、 in 8.1.3 followed by conditioning as specified in 8.1.2, except CBRN garment and material samples shall be conditioned as specified in 8.1.9 followed by conditioning as specified in 8.1.2. 8.16.2.2 Garment materials samples shall be conditioned as specified in 8.1.3 followed by conditioning as spec

28、ified in 8.1.2, except CBRN garment and material samples shall be conditioned as specified in 8.1.9 followed by conditioning as specified in 8.1.2. 21. Revise 8.16.8.1 to read as follows: 8.16.8.1 Samples for conditioning shall be in the form of a pouch as described in 8.1.15. 22. Revise 8.17.2.2 to

29、 read as follows: 8.17.2.2 Garment materials samples shall be conditioned as specified in 8.1.3 followed by conditioning as specified in 8.1.2, except CBRN garment and material samples shall be conditioned as specified in 8.1.9 followed by conditioning as specified in 8.1.2. 23. Revise 8.17.8.1 to r

30、ead as follows: 8.17.8.1 Samples for conditioning shall be in the form of a pouch as described in 8.1.15. 24. Revise 8.19.5.1to read as follows: 8.19.5.1 Specimen helmets shall be positioned on the headform according to the HPI as described in 8.1.12. Where the crown clearance of the helmet is adjus

31、table, the helmet shall be mounted with the least amount of clearance. Where an internal faceshield is an integral part of the structural integrity of the helmet, it shall be deployed as far as possible without interfering with the test equipment. Helmets shall be subjected to the environmental cond

32、itions specified in 8.1.2, 8.1.4, 8.1.5, and 8.1.6 prior to each impact and within the specified time after being removed from conditioning. 25. Revise 8.20.5.1 to read as follows: 8.20.5.1 The environmentally conditioned helmet shall be positioned according to the HPI as described in 8.1.132 on the

33、 test headform and secured by the helmet retention system or by other means that will not interfere with the test. Where the crown clearance of the helmet is adjustable, the helmet shall be mounted with the least amount of clearance. The helmet shall be positioned so that the penetration striker sha

34、ll impact perpendicular to the helmet. The helmet shall be adjusted to a size sufficient to properly fit on the headform with the horizontal center plane parallel and within 5 degrees of the reference plane. The front-to-back centerline of the shell shall be within 13 mm (0.5 in.) of the midsagittal

35、 plane of the headform. Where an internal faceshield is an integral part of the structural integrity of the helmet, it shall be deployed as far as possible without interfering with the test equipment. 26. Revise 8.21.5.1.1 to read as follows: 8.21.5.1.1 The helmet shall be positioned according to th

36、e HPI as described in 8.1.12 on the ISO size J headform specified in Figure 8.23.4.1. Where the crown clearance of the helmet is adjustable, the helmet shall be mounted with the most amount of clearance. 27. Revise 8.25.7.2 to read as follows: 8.25.7.2 Specimens shall be representative of glove body

37、 composite construction at glove areas A-P, B-P, D-P, E-P, F-P, G-P, H-P, I-P as described in 8.1.14. 28. Revise 8.26.7.2 to read as follows: 8.26.7.2 Specimens shall be representative of glove body composite construction at glove areas A-P, B-P, D-P, E-P, F-P, G-P, H-P, I-P, A-B, B-B, D-B, E-B, F-B

38、, G-B, H-B, I-B as described in 8.1.13. 29. Revise 8.27.7.2 to read as follows: 8.27.7.2 Specimens shall be representative of glove body composite construction at glove areas A-P, B-P, D-P, E-P, F-P, G-P, H-P, I-P as described in 8.1.13. All variations in composite construction and the order of laye

39、ring of composite materials shall constitute a new composite and shall be tested separately. 30. Revise 8.29.3.5, 8.29.4, and 8.29.5 to read as follows: 8.29.3.5 Specimen glove pairs shall be tested after being wet conditioned as specified in 8.1.7. 8.29.4 Apparatus. The apparatus shall consist of a

40、 pulling device that is a 31.7 mm (1 in.) diameter fiberglass pole attached to an overhead calibrated force measuring device in such a fashion that pulls on the pole will be perpendicular to the ground and downward in direction. This pole shall be used until surface degradation occurs. The force mea

41、suring system shall provide a graphical plot of force-vs-time. 8.29.5.4 The test subject and the test subjects hand shall be positioned as shown in Figure 8.29.5.4(a) and Figure 8.29.5.4(b), and as described below. 8.29.5.4.1 The test subject shall stand facing the pole with feet shoulder width apar

42、t. 8.29.5.4.2 While wearing specimen gloves, the test subject shall grasp the pole with the bottom of the bottom hand at a height equal to the height of the subject. 8.29.5.4.3 The hands shall be stacked on each other and the thumbs shall not overlap the fingers. 8.29.5.4.4 The body shall be distanc

43、ed from the pole so that the forearms are approaching vertical and in plane with the pole. 8.29.5.4.5 The elbows shall be shoulder width apart, rotated neither fully in (arms parallel to the pole) nor fully out (arms perpendicular to the pole). Figure 8.29.5.4(a) Position of test subject body, arms

44、and hands with respect to pole. Photo Courtesy Intertek Testing Services, Used by Permission. Figure 8.29.5.4(b) Close-up of position of test subject hands on pole. Photo Courtesy Intertek Testing Services, Used by Permission. 8.29.5.5 The test subject shall pull the pole with as much pulling force

45、as possible in a smooth, steady, swift, and non-jerking action for 5 +1/-0 seconds. The test subject shall minimize forward or backward movement during the pull as much as possible. The test subject shall not bend the knees or pull down with body weight during the pull. The test subject shall contin

46、ue to pull until the test facilitator instructs the test subject to end the pull at 5 +1/-0 seconds. 31. Delete existing subsections 8.29.5.5.1 through 8.29.5.5.6 and add a new subsection 8.29.5.6 to read as follows: 8.29.5.6 The test subject shall repeat the pull described above for a total of thre

47、e pulls. 32. Revise 8.29.6.1 to read as follows and delete 8.29.6.2 and 8.29.6.3: 8.29.6.1 Any drop in force of greater than 30% in any 0.2 second interval, as measured in the graphical plot of force versus time, shall be recorded and reported. 33. Revise 8.29.7.1 to read as follows: 8.29.7.1 Any dr

48、op in force of greater than 30% in any 0.2 second interval shall constitute failing performance. 34. Revise text as follows: 8.45.5.2 While standing, each test subject shall grasp the cylinder so that the elbow is against the side of the body throughout the duration of the test and the arm bend crea

49、tes a right angle. 8.45.5.4 Each test subject shall make five successive attempts to twist the cylinder in the appropriate direction exerting as much force as possible. The range of motion of the subjects wrist, shall indicate the end of the twisting cycle. The average maximum force over the five attempts shall be the barehanded control value. Issue Date: August 1, 2013 Effective Date: August 20, 2013 (Note: For further information on NFPA Codes and Standards, please see http:/www.nfpa.org/docinfolist) Copyright 2013 All Rights Reserved NATIONAL FIRE PROTECTION ASSOCIATIO