NFPA 259-2018 Standard Test Method for Potential Heat of Building Materials (Effective Date 11 30 2017).pdf

1、 NFPA 259 Standard T est Method for Potential Heat of Building Materials 2018IMPORTANT NOTICES AND DISCLAIMERS CONCERNING NFPA STANDARDS NOTICE AND DISCLAIMER OF LIABILITY CONCERNING THE USE OF NFPA STANDARDS NFPA codes, standards, recommended practices, and guides (“NFPA Standards”), of which the d

2、ocument contained herein is one, are developed through a consensus standards development process approved by the American National Standards Institute. This process brings together volunteers representing varied viewpoints and interests to achieve consensus on re and other safety issues. While the N

3、FPA administers the process and establishes rules to promote fairness in the development of consensus, it does not independently test, evaluate, or verify the accuracy of any information or the soundness of any judgments contained in NFPA Standards. The NFPA disclaims liability for any personal inju

4、ry, property, or other damages of any nature whatsoever, whether special, indirect, consequential or compensatory, directly or indirectly resulting from the publication, use of, or reliance on NFPA Standards. The NFPA also makes no guaranty or warranty as to the accuracy or completeness of any infor

5、mation published herein. In issuing and making NFPA Standards available, the NFPA is not undertaking to render professional or other services for or on behalf of any person or entity. Nor is the NFPA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this docu

6、ment should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. The NFPA has no power, nor does it undertake, to police or enforce compliance with the contents of NFPA S

7、tandards. Nor does the NFPA list, certify, test, or inspect products, designs, or installations for compliance with this document. Any certication or other statement of compliance with the requirements of this document shall not be attributable to the NFPA and is solely the responsibility of the cer

8、tier or maker of the statement. REVISION SYMBOLS IDENTIFYING CHANGES FROM THE PREVIOUS EDITION Text revisions are shaded. A before a section number indicates that words within that section were deleted and a to the left of a table or gure number indicates a revision to an existing table or gure. Whe

9、n a chapter was heavily revised, the entire chapter is marked throughout with the symbol. Where one or more sections were deleted, a is placed between the remaining sections. Chapters, annexes, sections, gures, and tables that are new are indicated with an N. Note that these indicators are a guide.

10、Rearrangement of sections may not be captured in the markup, but users can view complete revision details in the First and Second Draft Reports located in the archived revision information section of each code at www.nfpa.org/docinfo. Any subsequent changes from the NFPA Technical Meeting, Tentative

11、 Interim Amendments, and Errata are also located there. REMINDER: UPDATING OF NFPA STANDARDS Users of NFPA codes, standards, recommended practices, and guides (“NFPA Standards”) should be aware that NFPA Standards may be amended from time to time through the issuance of a Tentative Interim Amendment

12、 (TIA) or corrected by Errata. An ofcial NFPA Standard at any point in time consists of the current edition of the document together with any TIAs and Errata then in effect. To determine whether an NFPA Standard has been amended through the issuance of Tentative Interim Amendments or corrected by Er

13、rata, go to www.nfpa.org/docinfo to choose from the list of NFPA Standards or use the search feature to select the NFPA Standard number (e.g., NFPA 13). The document information page provides up-to-date document-specic information as well as postings of all existing TIAs and Errata. It also includes

14、 the option to register for an “Alert” feature to receive an automatic email notication when new updates and other information are posted regarding the document. ISBN: 978-145591907-9 (Print) ISBN: 978-145591908-6 (PDF) ISBN: 978-145591909-3 (eBook)IMPORTANT NOTICES AND DISCLAIMERS CONCERNING NFPA S

15、TANDARDS ADDITIONAL NOTICES AND DISCLAIMERS Updating of NFPA Standards Users of NFPA codes, standards, recommended practices, and guides (“NFPA Standards”) should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through t

16、he issuance of Tentative Interim Amendments or corrected by Errata. An ofcial NFPA Standard at any point in time consists of the current edition of the document together with any Tentative Interim Amendments and any Errata then in effect. In order to determine whether a given document is the current

17、 edition and whether it has been amended through the issuance of Tentative Interim Amendments or corrected through the issuance of Errata, consult appropriate NFPA publications such as the National Fire Codes Subscription Service, visit the NFPA website at www.nfpa.org, or contact the NFPA at the ad

18、dress listed below. Interpretations of NFPA Standards A statement, written or oral, that is not processed in accordance with Section 6 of the Regulations Governing the Development of NFPA Standards shall not be considered the ofcial position of NFPA or any of its Committees and shall not be consider

19、ed to be, nor be relied upon as, a Formal Interpretation. Patents The NFPA does not take any position with respect to the validity of any patent rights referenced in, related to, or asserted in connection with an NFPA Standard. The users of NFPA Standards bear the sole responsibility for determining

20、 the validity of any such patent rights, as well as the risk of infringement of such rights, and the NFPA disclaims liability for the infringement of any patent resulting from the use of or reliance on NFPA Standards. NFPA adheres to the policy of the American National Standards Institute (ANSI) reg

21、arding the inclusion of patents in American National Standards (“the ANSI Patent Policy”), and hereby gives the following notice pursuant to that policy: NOTICE: The users attention is called to the possibility that compliance with an NFPA Standard may require use of an invention covered by patent r

22、ights. NFPA takes no position as to the validity of any such patent rights or as to whether such patent rights constitute or include essential patent claims under the ANSI Patent Policy. If, in connection with the ANSI Patent Policy, a patent holder has led a statement of willingness to grant licens

23、es under these rights on reasonable and nondiscriminatory terms and conditions to applicants desiring to obtain such a license, copies of such led statements can be obtained, on request, from NFPA. For further information, contact the NFPA at the address listed below. Law and Regulations Users of NF

24、PA Standards should consult applicable federal, state, and local laws and regulations. NFPA does not, by the publication of its codes, standards, recommended practices, and guides, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing

25、 so. Copyrights NFPA Standards are copyrighted. They are made available for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of safe practices and methods. By making t

26、hese documents available for use and adoption by public authorities and private users, the NFPA does not waive any rights in copyright to these documents. Use of NFPA Standards for regulatory purposes should be accomplished through adoption by reference. The term “adoption by reference” means the ci

27、ting of title, edition, and publishing information only. Any deletions, additions, and changes desired by the adopting authority should be noted separately in the adopting instrument. In order to assist NFPA in following the uses made of its documents, adopting authorities are requested to notify th

28、e NFPA (Attention: Secretary, Standards Council) in writing of such use. For technical assistance and questions concerning adoption of NFPA Standards, contact NFPA at the address below. For Further Information All questions or other communications relating to NFPA Standards and all requests for info

29、rmation on NFPA procedures governing its codes and standards development process, including information on the procedures for requesting Formal Interpretations, for proposing Tentative Interim Amendments, and for proposing revisions to NFPA standards during regular revision cycles, should be sent to

30、 NFPA headquarters, addressed to the attention of the Secretary, Standards Council, NFPA, 1 Batterymarch Park, P.O. Box 9101, Quincy, MA 02269-9101; email: stds_adminnfpa.org. For more information about NFPA, visit the NFPA website at www.nfpa.org. All NFPA codes and standards can be viewed at no co

31、st at www.nfpa.org/docinfo.259-1 NFPA and National Fire Protection Association are registered trademarks of the National Fire Protection Association, Quincy, Massachusetts 02169. Copyright 2017, National Fire Protection Association . All Rights Reserved. NFPA 259 Standard Test Method for Potential H

32、eat of Building Materials 2018 Edition This edition of NFPA 259, Standard Test Method for Potential Heat of Building Materials, was prepared by the Technical Committee on Fire Tests. It was issued by the Standards Council on November 10, 2017, with an effective date of November 30, 2017, and superse

33、des all previous editions. This edition of NFPA 259 was approved as an American National Standard on November 30, 2017. Origin and Development of NFPA 259 This standard is based on a test method developed at the National Bureau of Standards in 1961. Consideration of the test method by the NFPA was b

34、egun in 1973, culminating in the standard that was adopted in 1976, reconrmed in 1981, and revised at the 1986 Fall Meeting. The 1993 edition was a reconrmation of the 1987 edition. The 1998 edition was completely rewritten, incorporating editorial changes with the elimination of nonmandatory langua

35、ge. The only signicant technical change was the incorporation of the requirement of two tests for a product to determine its heat of combustion. A maximum 10 percent variation was permitted; otherwise, a third test was required. Also in 1998, a new Appendix A was added, providing explanatory materia

36、l. A new Appendix C containing material extracted from Appendix C of NFPA 220, Standard on Types of Building Construction, was added for informational purposes. The 2003 edition of NFPA 259 was updated to incorporate the requirements of the Manual of Style for NFPA Technical Committee Documents. The

37、 2008 edition of NFPA 259 was a reconrmation of the 2003 edition. The 2013 edition included a new test limitation, revised oxygen bomb calorimeter requirements, and revised annex material. The 2018 edition includes new Annex B material on the use of potential heat data.POTENTIAL HEAT OF BUILDING MAT

38、ERIALS 259-2 2018 Edition Technical Committee on Fire Tests Barry L. Badders, Jr., Chair Intertek Testing Services, TX RT Farid Alfawakhiri, American Iron and Steel Institute, IL M James A. Burns, New York State Department, NY E Rep. Firemens Association of the State of New York Karen C Carpenter, S

39、outhwest Research Institute, TX RT Gordon H. Damant, Inter-City Testing & Consulting Corp. of California, CA SE Rick D. Davis, National Institute of Standards & Technology, MD RT Scott E. Dillon, Crane Engineering, MN SE William E. Fitch, P, FL SE Richard G. Gann, Gaithersburg, MD SE Marcelo M. Hirs

40、chler, GBH International, CA SE Paul A. Hough, Armstrong World Industries, Inc., PA M William E. Koffel, Koffel Associates, Inc., MD SE Sergei V. Levchik, Israel Chemicals Ltd. (ICL-IP), NY M Rep. ACC-North American Flame Retardant Alliance James Andrew Lynch, The Fire Solutions Group, PA SE John Ma

41、rtell, Professional Fire Fighters of Maine/IAFF, ME L Rep. International Association of Fire Fighters Rodney A. McPhee, Canadian Wood Council, Canada M Kathleen A. Newman, Firetect, CA M Arthur J. Parker, JENSEN HUGHES, MD SE Michael L. Savage, Sr., City of Rio Rancho, NM E Michael Schmeida, Gypsum

42、Association, OH M David T. Sheppard, U.S. Bureau of Alcohol, Tobacco, Firearms & Explosives, MD RT Dwayne E. Sloan, UL LLC, NC RT Stanislav I. Stoliarov, University of Maryland, MD SE Kuma Sumathipala, American Wood Council, VA M Dong Zeng, FM Global, MA I Rep. FM Global Alternates Erik H. Anderson,

43、 Koffel Associates, Inc., MD SE (Alt. to William E. Koffel) Jesse J. Beitel, JENSEN HUGHES, MD SE (Alt. to Arthur J. Parker) Richard J. Davis, FM Global, MA I (Alt. to Dong Zeng) Timothy Earl, GBH International, MI SE (Alt. to Marcelo M. Hirschler) Sam W. Francis, American Wood Council, PA M (Alt. t

44、o Kuma Sumathipala) Stephen Paul Fuss, U.S. Bureau of Alcohol, Tobacco, Firearms & Explosives, MD RT (Alt. to David T. Sheppard) Justin A. Geiman, Fire and Risk Alliance LLC, MD SE (Alt. to James Andrew Lynch) Karl Dana Houser, Intertek, PA RT (Alt. to Barry L. Badders, Jr.) Marc L. Janssens, Southw

45、est Research Institute, TX RT (Alt. to Karen C Carpenter) Ineke Van Zeeland, Canadian Wood Council, Canada M (Alt. to Rodney A. McPhee) Matthew T. Vinci, International Association of Fire Fighters, DC L (Alt. to John Martell) Robert J. Wills, American Iron and Steel Institute, AL M (Alt. to Farid Al

46、fawakhiri) Luke C. Woods, UL LLC, MA RT (Alt. to Dwayne E. Sloan) Joe Ziolkowski, American Furniture Manufacturers Association, NC M (Voting Alternate) Nonvoting Robert H. Barker, American Fiber Manufacturers Association, VA M Rep. American Fiber Manufacturers Association Rohit Khanna, U.S. Consumer

47、 Product Safety Commission, MD C Rep. U.S. Consumer Product Safety Commission Andrew Lock, U.S. Consumer Product Safety Commission, MD C Rep. U.S. Consumer Product Safety Commission Tracy L. Vecchiarelli, NFPA Staff Liaison This list represents the membership at the time the Committee was balloted o

48、n the nal text of this edition. Since that time, changes in the membership may have occurred. A key to classications is found at the back of the document. NOTE: Membership on a committee shall not in and of itself constitute an endorsement of the Association or any document developed by the committe

49、e on which the member serves. Committee Scope: This Committee shall have primary responsibility for documents on re testing procedures, for reviewing existing re test standards and recommending appropriate action to NFPA, for recommending the application of and advising on the interpretation of acceptable test standards for re problems of concern to NFPA technical committees and members, and for acting in a liaison capacity between NFPA and the committees of