PFI ES-37-2006 STANDARD FOR LOADING AND SHIPPING OF PIPING ASSEMBLIES《管道总成装载和运送标准》.pdf

1、 PFI Standard ES-37 (Reaffirmed September 2010) STANDARD FOR LOADING AND SHIPPING OF PIPING ASSEMBLIES Prepared by Pipe Fabrication Institute Engineering Committee All PFI Standards are advisory only. There is no agreement to adhere to any PFI Standard and their use by anyone is entirely voluntary.

2、Copyright by PIPE FABRICATION INSTITUTE Dedicated to Technical Advancements and Standardization in the Pipe Fabrication Industry Since 1913 USA 511 Avenue of Americas, # 601 New York, NY 10011 CANADA 655, 32ndAvenue, # 201 Lachine, QC H8T 3G6 WEB SITE www.pfi-institute.orgPFI Standard ES-37 (Reaffir

3、med September 2010) STANDARD FOR LOADING AND SHIPPING OF PIPING ASSEMBLIES 1. Scope 1.1 This Standard establishes the minimum requirements for the loading of prefabricated piping assemblies on full truckloads to minimize or prevent damage during subsequent shipment. 1.2 The loading and shipping meth

4、ods described in this Standard are considered minimum protection. Due to the infinite possibilities of size and configuration of piping assemblies additional measures may be necessary for certain types of fabrication subject to agreement between the customer and the fabricator. 2. Loading 2.1 Proced

5、ures for loading normally include the following: 2.1.1 A bottom layer of dunnage, adequate to ensure that forklift forks will fit between the fabricated pipe and the truck bed, will be placed at regular intervals across the bottom loading surface. 2.1.2 Spools of infinite configuration are loaded an

6、d placed in the best possible way to prevent movement and damage during shipment. Large diameter or heavy wall fabrication should always be placed on the bottom of the load with smaller and lighter weight materials placed on top of the load. 2.1.3 It is recommended that slings of fabric construction

7、 be used for loading fabricated piping. 2.1.4 When possible, spools of a “straight” configuration should be loaded in a layered manner with dunnage placed between each layer. 2.1.5 Major abrasive contact points between painted spools should be protected by placing a protective material such as plast

8、ic foam, rubber, or wood between the spools to minimize damage. Particular care should be taken to protect and prevent contact between machined surfaces such as the gasket sealing area of flanges. 2.1.6 When carbon steel and stainless steel materials are loaded on the same transportation, non-contac

9、t separation between such materials shall be provided. 2.1.7 Small assemblies, loose material or supports may be packaged (i.e., boxed, crated, palletized or contained in stretch wrap) for protection and security during shipment. Alternate means such as side kits or stakes may be necessary to secure

10、 small spools. 2.1.8 Over-width, over-height, or over-length loads require special consideration subject to agreement between the customer, fabricator, and the carrier. 3. Shipping 3.1 Final securing and tie down of the load is the responsibility of the carrier. 3.1.1 It is recommended that slings o

11、f fabric construction be used for securing fabricated piping. Chains or metal slings (i.e., cable) may be used provided sufficient measures are taken to prevent damage (or carbon steel contamination of stainless materials) to pipe assemblies. 3.2 An itemized packing list should accompany each shipme

12、nt of fabricated piping assemblies. 4. Safety 4.1 All employees engaged in loading trucks with fabrication shall be instructed in the applicable safety procedures as required by statute and by company policies. At minimum: 4.1.1 Prior to each use, all slings and lifting equipment shall be checked fo

13、r any visible damage and to ensure that their load-bearing capacity is sufficient for the job at hand. 4.1.2 Equipment operators and riggers shall be properly trained and familiar with the equipment and the standard hand signals. 4.1.3 Employees shall be trained in fall protection so that they can identify potential hazards and take appropriate steps to mitigate them. 4.2 Equipment operators and riggers should be properly trained and familiar with equipment and standard hand signals.