1、Best Practices Entry: Best Practice Info:a71 Committee Approval Date: 2000-03-09a71 Center Point of Contact: JSCa71 Submitted by: Wil HarkinsSubject: Designing for Dormant Reliability Practice: Use appropriate design considerations to enhance the reliability characteristics of a system or item when
2、its intended use involves long periods of dormancy or nonoperation.Programs that Certify Usage: N/ACenter to Contact for Information: JSCImplementation Method: This Lesson Learned is based on Reliability Guideline Number GD-ED-2207 from NASA Technical Memorandum 4322A, NASA Reliability Preferred Pra
3、ctices for Design and Test.Benefits:The likelihood of successful system operation after long periods of dormancy can be increased by assessing the long term environmental effects on the characteristics of parts and materials, and mitigating the detrimental effects through appropriate parts selection
4、 and use of protective design options.Implementation Method:Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-The approach involves detailed examination of the materials, parts, and manufacturing methods used in the design and construction of systems a
5、nd appropriate consideration of the systems intended environmental factors. The steps involved include the following:1. Categorize the system or item into constituent components.2. Define the system or item life environments and consider the effects of environmental factors on the constituent compon
6、ents.3. Where possible, examine quantitative estimates of dormant failure rates for indications of potential problems.4. Use published guidelines and checklists for dormant system design considerations.Categorize the System/Item Into Constituent ComponentsThe item under consideration should be itemi
7、zed by its constituent parts down to the “component,“ material, and electronic piece-part level, if possible. For the purposes of this guideline, a component is defined as a functional unit viewed as an entity for analysis, manufacturing, maintenance, or record keeping tasks. Materials, parts, and c
8、omponents used in the system may also be characterized into the following general types when in the nonoperating or dormant states:1. Components or parts with indefinite nonoperating lives which are subject to “random failure“ mechanisms (Type A). Electronic parts and components are usually associat
9、ed with this characteristic.2. Materials and components which degrade at a slow but relatively predictable rate over time (Type B). Many electromechanical and mechanical components, pyrotechnics, and organic materials can be considered to exhibit this characteristic.3. Materials and components which
10、 have known, relatively short, limited shelf lives (Type C). Items with this characteristic are generally well known: batteries, some solar panels, gas generators, etc.Type A DevicesThe principal failure mechanisms for electronic equipment and parts occurring during non-operative phases of the parts
11、 life are caused by latent manufacturing defects or deficiencies in materials rather than specific aging mechanisms. As a result of these latent manufacturing defects, environmental conditions and stresses act upon these defects until sufficient conditions exist for degradation failure to occur. One
12、 of the most effective ways to reduce these types of failures is to subject the component or assembly to programs such as environmental stress screening (ESS). Programs such as these should be capable of detecting failure mechanisms including defects in bulk material, metallization, final seals, wir
13、e bonding, glassivation, die bonding, oxide, and diffusion as well as general Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-contamination problems. However, an ESS program should be carefully designed to restrict the environmental excursions and st
14、ress cycles so as to not induce incipient failures.Types B and C Devices and MaterialsIn general, nonorganic materials such as metals deteriorate by electrochemical processes, and organic materials deteriorate by chemical reactions. Most organic materials used in spacecraft are long-chain polymeric
15、compounds which degrade through the breakdown of the compound into smaller, more volatile fragments, making polymers the most likely to be affected by the vacuum of a hostile space environment. Therefore, organic materials exposed to a vacuum may decompose into volatile products in warmer areas, and
16、 redeposit onto relatively cooler surfaces. If the cooler surfaces are thermodynamically or electrically conductive by design, a malfunction is likely to occur. Of particular concern are failure modes that occur because of plasticizers redepositing onto exposed relay contacts preventing proper closi
17、ng of the circuit.In the absence of oxygen, polymers are more stable at elevated temperatures. However, nylons, polysulfides, cellulosics, acrylics, polyesters, epoxies, and urethanes possess unstable properties in low-pressure or vacuum environments. The stability of the polymer in a vacuum is depe
18、ndent upon formulation and curing procedures used during the manufacturing processes where plasticizers, mold lubricants, and polymerization catalysts are generally detrimental to long-term reliability. Therefore, the use of devices constructed with polymers that use these agents should be avoided.
19、Nevertheless, exposure to vacuum conditions generally causes no loss of engineering properties in seals or gaskets unless an appreciable loss in mass occurs.Define the System or Item Life Environments and Consider the Effects of Environmental Factors on the Constituent ComponentsThe designer should
20、identify and develop the environmental operating conditions and factors that will apply to each phase of the items life cycle. For instance, if an item is to be stored in a warehouse for most of its life cycle, the environment it sees would be significantly different than a component on an orbiting
21、satellite. The primary environmental factors encountered during storage or nonoperating phases of space systems are listed below.a71 High Temperature Extremesa71 Low Temperature Extremesa71 Temperature Cyclinga71 Moisturea71 Low Pressure (Vacuum)a71 Atmospheric Pollutantsa71 Thermal Shocka71 Nuclear
22、 Radiationa71 Electromagnetic Fieldsa71 Corrosiona71 Solar Radiation/Atomic Oxygena71 Mechanical Shock/Vibrationa71 Mechanical Shock/Vibrationa71 Bacteria, Fungia71 Static Electrical ChargesProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-The relative
23、 stress levels experienced by individual components or assemblies during a dormant period are very greatly reduced from operating levels. Consequently, designs for dormant reliability must focus much more heavily on understanding the failure mechanisms which will be experienced in the dormant enviro
24、nments, the factors which cause each of the failure mechanisms to occur, and methods for controlling the occurrence of the failure mechanism.The most important environmental stresses produced by the environmental factors encountered in dormancy are mechanical, chemical, and low thermal (Reference 8)
25、. The mechanical stresses are primarily due to inertial forces (during transportation and handling) and thermal-mechanical interactions which introduce differential expansion between materials within a device and between subassemblies and interconnections. Diurnal- and/or orbital-induced temperature
26、 cycles should therefore be as small as possible. Chemical stresses are primarily influenced by contaminants such as halogen ions, residual process chemicals, and water (moisture). In fact, moisture within a device or assembly package is the most important factor for both corrosion and mechanically
27、induced failures (Reference 8). There is a substantial number of design techniques and methods to mitigate the effects of these environmental factors found in sources such as References 7 and 8.Radiation particles, ultra-violet wavelength light exposure, and atomic oxygen are all detrimental to expo
28、sed polymeric materials. Solar flare emissions will probably affect exposed surfaces of the materials more sensitive to radiation damage. The results of the Long Duration Exposure Facility have recently been released and indications are that low Earth orbits cause significant wear and erosion to exp
29、osed materials. Kapton seems to be highly susceptible to atomic oxygen, and erosion of silverized Teflon is somewhat more than that predicted by ground-based tests.Examine Quantitative Estimates of Nonoperating Failure Rates of Items Considering the Appropriate EnvironmentsExamination of historical
30、failure rates of similar items may provide indications of areas for concern. For electronic parts and other mechanical items classified as Type A items, several publications provide methods and historical data for estimating a failure rate in a dormant or nonoperating state. Reference 7 provides a c
31、ompendium of models for estimating the failure rate for various types of components as a function of environment, part type and quality level, and ambient temperature similar to the methods used in MIL-HDBK-217. Values for base failure rates and modifying parameters were derived from numerous field
32、data sources (which are primarily missile and aircraft system information), and are delineated in the document. Other documents (e.g., Reference 4) also provide estimates of the nonoperating or dormant rate of failure for components that have been derived from historical field and test data.The gene
33、ral characteristics of the failure properties of Types B and C items can usually be described as a period of fairly low rate of failure followed by an increasing propensity to fail as the item begins to degrade or wear out. Therefore, constant failure rates are not applicable to these items, and the
34、 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-designer should consider sources or methods for estimating the life limits or life parameters.Mathematical equations for calculating the individual component reliabilities over a prescribed mission tim
35、e may also be used. In less complex systems, appropriate reliability block diagrams may be used to aggregate the component reliabilities and to derive the likelihood of the system being able to perform its function over a specified period of time. However, the inherent uncertainty involved in applyi
36、ng the observed nonoperating failure rates of older technology parts to more current components limits the ability to provide an accurate specification for system reliability over long time periods.Use Published Guidelines and Checklists for Dormant System Design ConsiderationsThe designer is urged
37、to use published sources such as “Reliability/Maintainability/Testability Design for Dormancy,“ (Reference 8) that provide detailed design guidelines and checklists for reference when designing systems for storage or long periods of nonoperation. Table 1 lists some of the general points that should
38、be considered from an overall system viewpoint.Table 1. General Dormant Reliability Checklist Yes No N/AHas a packaging, transportation, handling, and storage environmental analysis been completed?Has the dormant mean time between failure attained in service been used as a criterion for component se
39、lection?Have the major dormant/storage failure modes and effects been analyzed?Are adequate integrity checks identified for uncovering dormant/storage failures prior to flight?Can dormant/storage failures be readily detected and isolated? Will the equipment withstand any natural combination of the d
40、ormant/storage environments(e.g., shock vibration, acceleration, temperature cycles, humidity, and atomic oxygen.) in the intended application?Have the restrictions in employing dissimilar metals in intimate contact been considered?Have thermal stresses and differential thermal expansion been consid
41、ered?Is aging a factor considered? Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Is the production process likely to degrade the dormant/storage reliability?Are provisions made to prevent the entrapment of moisture or other fluids?Do protective coa
42、tings meet requirements? Are limited-life items identified? Was corrosive degradation considered? Technical Rationale:When designing systems with aspects of dormancy in their life cycle profile, consideration must be given to degradation and failure while in the nonoperating state. Items can and wil
43、l fail during periods of nonoperation. Dormant reliability is defined here as the probability (or likelihood) that an item or system will operate as intended after undergoing a long period of inactivity or nonoperation. Dormant systems may spend 90 percent or more of their life cycle profile in envi
44、ronments that may be detrimental to their survival. Environmental stresses, as well as aging effects, will precipitate failures just as do stresses during operating periods.References:1. AFWAL-TR-83-2079, “Weibull Analysis Handbook,“ Air Force Wright Aeronautical Laboratories, United States Air Forc
45、e, Wright-Patterson AFB, November 19832. EERD-3, “Nonelectronic Parts Reliability Data,“ Rome Air Development Center, Reliability Analysis Center, 19863. MIL-STD-1540B (USAF), “Military Standard Test Requirements For Space Vehicles,“ October 10, 19824. NONOP-1, “Non Operating Reliability Databook,“
46、Rome Air Development Center, Reliability Analysis Center, 19875. NPRD-3, “Nonelectronic Parts Reliability Data,“ Rome Air Development Center, 19856. PRC-R-4416, “Analysis of In-Flight Spacecraft Performance and Anomaly Data,“ October 19847. RADC-TR-85-91, “Impact of Nonoperating Periods On Equipment
47、 Reliability,“ Rome Air Development Center, May 19858. RADC-TR-88-110 “Reliability/Maintainability/Testability Design For Dormancy,“ Rome Air Development Center, May 1988.9. SD-TR-86-02, “Analysis of Orbital Satellite Stage,“ Air Force Systems Command, November 1985.10. “Dormant Reliability Awarenes
48、s Seminar,“ The BDM Corporation, May 198611. “RADC Reliability Engineers Toolkit,“ Rome Air Development Center, July 198812. Fisher, Dr. William F., and Price, Charles R.: “Space Station Freedom External Maintenance Provided by IHSNot for ResaleNo reproduction or networking permitted without license
49、 from IHS-,-,-Task Team Final Report,“ July 199013. “Reliability & MIL-HDBK-217 Prediction,“ Reliability Review, Volume 10 pp. 7-9, September 199014. Reliability Preferred Practice No. PD-EC-1101: Environmental FactorsImpact of Non-Practice: When designing systems with aspects of dormancy in their life cycle profile, it is vitally important that consideration be given
copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1