SAE AMS 2263E-2006 Tolerances Nickel Nickel Alloy and Cobalt Alloy Tubing《镍、镍合金和钴合金管的公差》.pdf

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2017 SAE InternationalAll rights reserved. No part of this publi

3、cation may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (out

4、side USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AMS2263E AEROSPACEMATERIAL SPECIFICATIONAMS2263 REV. E Issued 1948-11Revised 2006-05Reaffirmed 2017-12

5、Superseding AMS2263D TolerancesNickel, Nickel Alloy, and Cobalt Alloy Tubing RATIONALEAMS2263E has been reaffirmed to comply with the SAE Five-Year Review policy.1. SCOPEThis specification covers established inch-pound manufacturing tolerances applicable to seamless and welded thin-wall aircraft tub

6、ing of nickel, nickel alloys, and cobalt alloys ordered to inch-pound dimensions. These tolerances apply to all conditions and are based on individual measurements, unless otherwise noted. The term “exclusive“ is used to apply only to the higher figure of a specified range. 2. DIAMETERMean diameter

7、is the average of two measurements taken at right angles to each other at the same section. Ovality is the difference between the maximum and minimum diameters of any one section of a tube. 2.1 Seamless, Cold Finished 2.1.1 Nickel-Copper Alloy, Annealed TABLE 1 - DIAMETER TOLERANCES, ANNEALED NICKEL

8、-COPPER ALLOY Specified OD Inches Specified Wall Thickness % of OD Tolerance, Inch OD Plus Tolerance, Inch OD Minus Tolerance, Inch Mean OD Plus Tolerance, Inch Mean OD Minus Ovality Up to 0.400, incl Up to 3.0, incl - - 0.004 0 0.004 Over 3.0 0.004 0 - - - Over 0.400 to 0.625, excl Up to 3.0, incl

9、- - 0.005 0 0.005 Over 3.0 0.005 0 - - - 0.625 to 1.500, incl Up to 3.0, incl - - 0.005 0.005 0.01 OD Over 3.0 0.005 0.005 - - - Over 1.500 to 4.500, incl Up to 3.0, incl - - 0.010 0.010 0.01 OD Over 3.0 0.010 0.010 - - - Over 4.500 to 6.000, incl Up to 3.0, incl - - 0.015 0.015 0.01 OD Over 3.0 0.0

10、30 0.030 0.015 0.015 - Over 6.000 to 7.500, incl Up to 3.0, incl - - 0.020 0.020 0.01 OD Over 3.0 0.040 0.040 0.020 0.020 - Over 7.500 to 8.625, incl Up to 3.0, incl - - 0.025 0.025 0.01 OD Over 3.0 0.050 0.050 0.025 0.025 - 2.1.2 Nickel-Chromium-Iron Alloy, Annealed TABLE 2 - DIAMETER TOLERANCES, A

11、NNEALED NICKEL-CHROMIUM-IRON ALLOY Specified OD Inches Specified Wall Thickness % of OD Tolerance, Inch OD Plus Tolerance, Inch OD Minus Tolerance, Inch Mean OD Plus Tolerance, Inch Mean OD Minus Ovality Up to 0.400, incl Up to 3.0, incl - - 0.004 0 0.004 Over 3.0 0.004 0 - - - Over 0.400 to 0.625,

12、excl Up to 3.0, incl - - 0.005 0.005 0.005 Over 3.0 0.005 0.005 - - - 0.625 to 1.500, incl Up to 3.0, incl - - 0.0075 0.0075 0.01 OD Over 3.0 0.0075 0.0075 - - - Over 1.500 to 3.500, incl Up to 3.0, incl - - 0.010 0.010 0.01 OD Over 3.0 0.010 0.010 - - - Over 3.500 to 4.500, incl Up to 3.0, incl - -

13、 0.015 0.015 0.01 OD Over 3.0 0.015 0.015 - - - Over 4.500 to 6.000, incl Up to 3.0, incl - - 0.020 0.020 0.01 OD Over 3.0 0.040 0.040 0.020 0.020 - Over 6.000 to 6.625, incl Up to 3.0, incl - - 0.025 0.025 0.01 OD Over 3.0 0.050 0.050 0.025 0.025 - SAE INTERNATIONAL AMS2263E Page 2 of 5_ 2.2 Copper

14、 Furnace Brazed, Cold Finished 2.2.1 Nickel-Copper Alloy, Annealed TABLE 3 - DIAMETER TOLERANCES, ANNEALED NICKEL-COPPER ALLOY Specified OD Inch Specified Wall Thickness Inch OD Tolerance Inch Plus OD Tolerance Inch Minus 0.125 0.028 0.001 0.001 0.188 0.028 0.001 0.001 0.250 0.028 0.003 0 0.312 0.02

15、8 0.003 0 0.375 0.028 0.003 0 0.500 0.028 0.005 0 0.625 0.028 0.005 0 0.625 0.035 0.005 0 2.3 Welded, All Alloys OD tolerances apply to mean OD for tubing with specified wall thickness of 3% or less of specified OD. OD and ID tolerances shall not both apply to the same lot of tubing. TABLE 4 - DIAME

16、TER TOLERANCES AND OVALITY, ALL ALLOYS, WELDED TUBING Specified OD Inches Specified Wall Thickness % of OD Tolerance, Inch Plus and Minus OD Tolerance, Inch Plus and Minus ID Ovality Up to 0.094, incl Up to 3.0, incl 0.001 0.001 0.001 Over 3.0 0.001 0.001 - Over 0.094 to 0.1875, excl Up to 3.0, incl

17、 0.0015 0.0015 0.002 Over 3.0 0.0015 0.0015 - 0.1875 to 0.500, excl Up to 3.0, incl 0.003 0.005 0.004 Over 3.0 0.003 0.005 - 0.500 to 1.000, excl Up to 3.0, incl 0.004 0.006 0.01 OD Over 3.0 0.004 0.006 - 1.000 to 1.500, excl Up to 3.0, incl 0.005 0.007 0.01 OD Over 3.0 0.005 0.007 - 1.500 to 2.000,

18、 excl Up to 3.0, incl 0.006 0.008 0.01 OD Over 3.0 0.006 0.008 - 2.000 to 2.500, excl Up to 3.0, incl 0.007 0.010 0.01 OD Over 3.0 0.007 0.010 - 2.500 to 3.500, excl Up to 3.0, incl 0.010 0.014 0.01 OD Over 3.0 0.010 0.014 - 3.500 to 5.000, excl Up to 3.0, incl 0.015 0.020 0.01 OD Over 3.0 0.015 0.0

19、20 - 3. WALL THICKNESS 3.1 Seamless, Cold Finished 3.1.1 Wall thickness of all tubes except for those alloys and sizes shown in 3.1.2 and 3.1.3 shall not vary more than 10%. SAE INTERNATIONAL AMS2263E Page 3 of 5_ 3.1.2 Nickel-Copper Alloy, Seamless 3.1.2.1 Wall thickness may vary 12.5% for the foll

20、owing sizes: 3.1.2.1.1 Tubes with specified OD over 0.400 to 0.625 inch, exclusive, with specified wall thickness of 0.040 inch and over. 3.1.2.1.2 Tubes with specified wall thicknesses more than 25% of the specified OD. 3.1.2.1.3 Tubes over 4.500 inches in specified OD. 3.1.3 Nickel-Chromium-Iron A

21、lloy, Seamless 3.1.3.1 Wall thickness may vary 15% for the following sizes: 3.1.3.1.1 Tubes with specified OD over 0.400 to 0.625 inch, exclusive, with specified wall thicknesses of 0.042 inch and over. 3.1.3.1.2 Tubes with specified wall thicknesses more than 25% of the specified OD. 3.1.3.2 Wall t

22、hickness may vary 12.5% for tubes over 4.500 inches in specified OD. 3.2 Copper Furnace Brazed, Cold Finished Wall thickness of nickel-copper alloy tubes shall not vary more than 0.002 inch. 3.3 Welded, All Alloys For tubes with specified OD 0.625 inch, and under, wall thickness tolerances of seamle

23、ss tubing apply. Wall thickness tolerances are 10% for redrawn welded tubing. TABLE 5 - WALL THICKNESS TOLERANCES, WELDED TUBING, ALL ALLOYS Specified Wall Thickness Inch Wall Thickness Tolerance, Inch Plus and Minus OD Ranges, Inch Over 0.625 to 1.000 excl Wall Thickness Tolerance, Inch Plus and Mi

24、nus OD Ranges, Inch 1.00 to 2.00 excl Wall Thickness Tolerance, Inch Plus and Minus OD Ranges, Inch 2.00 to 4.00 excl Wall Thickness Tolerance, Inch Plus and Minus OD Ranges, Inch 4.00 to 5.00 excl Up to 0.025, incl 0.002 0.003 - - Over 0.025 to 0.028, incl 0.003 0.003 - - Over 0.028 to 0.032, incl

25、0.003 0.004 0.004 - Over 0.032 to 0.049, incl 0.003 0.004 0.005 0.005 Over 0.049 to 0.058, incl 0.004 0.005 0.005 0.006 Over 0.058 to 0.065, incl 0.005 0.005 0.005 0.006 Over 0.065 to 0.095, incl 0.005 0.005 0.006 0.007 Over 0.095 to 0.120, incl 0.005 0.006 0.007 0.007 Over 0.120 to 0.134, incl - -

26、0.007 0.007 Over 1.134 to 0.165, incl - - 0.008 0.008 4. LENGTH Definite lengths shall not vary more than plus 0.125 inch, minus 0. 5. STRAIGHTNESS Tubes 4 inches and under in specified OD shall be of such straightness that the maximum curvature (depth of arc) shall be not greater than 0.060 inch in

27、 any 3 feet of length or 0.020 inch length in feet for shorter lengths. 6. NOTES SAE INTERNATIONAL AMS2263E Page 4 of 5_ 6.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previo

28、us issue of this specification. An (R) symbol to the left of the document title indicates a complete revision of the specification, including technical revisions. Change bars and (R) are not used in original publications, nor in specifications that contain editorial changes only. 6.2 Terms used in A

29、MS are clarified in ARP1917. 6.3 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 6.4 Key Words Tolerances, seamless and welded thin-wall aircraft tubing, nickel, nickel alloys, cobalt alloys PREPARED BY AMS COMMITTEE “F“ SAE INTERNATIONAL AMS2263E Page 5 of 5_