SAE AMS 2813G-2011 Packaging and Marking of Packages of Welding Wire Standard Method《焊条装箱的包装和标识的标准方法》.pdf

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AMS2813G AEROSPACE MATERIAL SPECIFICATION AMS2813 REV. G Issued 1963-01 Revised 2011-03 Reaffir

5、med 2017-08 Superseding AMS2813F Packaging and Marking of Packages of Welding Wire Standard Method RATIONALE AMS2813G has been reaffirmed to comply with the SAE Five-Year Review policy. 1. SCOPE This specification covers spooling and packaging of bare welding wire to ensure cleanliness but with mini

6、mum environmental protection, spool sizes and weights of spooled wire, and package weights of cut lengths. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work

7、 to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 U.S. Government Publications Available from the Document A

8、utomation and Production Service (DAPS), Building 4/D, 700 Robbins Avenue, Philadelphia, PA 19111-5094, Tel: 215-697-6257, http:/assist.daps.dla.mil/quicksearch/. MIL-W-10430 Welding Rods and Electrodes, Preparation for Delivery of 2.2 American Welding Society Available from American Welding Society

9、, 550 N.W. LeJeune Rd., Miami, FL 33126, U.S.A. and . AWS A5.02/A5.02M Specification for Filler Metal Standard Sizes, Packaging, and Physical Attributes 2.3 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada)

10、or 724-776-4970 (outside USA), www.sae.org. AMS2816 Identification, Welding Wire, Tab Marking System AMS2819 Identification Welding Wire, Direct Color Code System SAE INTERNATIONAL AMS2813G Page 2 of 4 3. TECHNICAL REQUIREMENTS 3.1 Preparation Prior to winding on spools or cutting to length, wire sh

11、all be uncoiled for cleaning and shall be rendered free of dirt, grease, oil, corrosion, and other surface contamination which would interfere with welding. Chorinated solvents shall not be used on titianium alloys. 3.2 Packaging shall be in accordance with AWS A5.02/A5.02M and the following: 3.2.1

12、Spooled Wire Each spool shall provide access to approximately 8 inches (203 mm) of wire at the inside end of the coil for sampling purposes; a groove in the outer face of one flange, adjacent to the barrel, is acceptable. 3.2.1.1 Unless otherwise specified in the material specification, wire on each

13、 spool shall be one continuous length from the same heat of alloy, except in the case of aluminum and magnesium alloys which are not restricted. 3.2.1.2 Wire shall be furnished on spools containing approximately the ordered spool net weight except that up to 20% of the net weight of any one combinat

14、ion of alloy, wire diameter, and spool size in a shipment may be on spools containing not less than 50% of the ordered spool net weight. 3.2.1.3 Wire shall be closely wound in layers but adjacent turns within a layer need not necessarily be touching; shall be wound so as to avoid producing kinks, wa

15、ves, and sharp bends; and shall be free to unwind without restriction caused by overlapping or wedging. The outside end of the spooled wire shall be so treated that it may be readily located. 3.2.1.4 Net weight of wire on spools shall be as specified in Table 1 for the alloy type ordered. 3.2.2 Cut

16、Lengths 3.2.2.1 Containers shall be of such materials and construction as to provide sufficient strength and rigidity to prevent damage to, or distortion of, the wire during normal handling. The materials shall not induce corrosion of the wire. 3.2.2.2 Unless otherwise specified in the material spec

17、ification, no package shall contain wire from more than one heat of alloy, except in the case of packages of aluminum and magnesium alloys which are not restricted. 3.2.2.3 Wire shall be furnished in standard packages of approximately 5, 10, 25, 50, or 100 pounds (2.3, 4.5, 11.3, 22.7, or 45.3 kg),

18、as ordered. 3.3 Packaging 3.3.1 Containers of wire shall be packed to ensure that the wire, during shipment and storage, will be protected against mechanical damage, corrosion, dirt, grease, oil, and other contamination detrimental to welding. 3.3.2 Exterior containers of spooled wire shall contain

19、the ordered multiple of standard spool net weights up to a maximum net weight of 120 pounds (54.4 kg). SAE INTERNATIONAL AMS2813G Page 3 of 4 TABLE 1A - SPOOLED WIRE WEIGHT, INCH/POUND UNITS Alloy Base Net Weight, Pounds Aluminum 1, 5, 10, 12-1/2, 15 Magnesium 3/4, 1, 3, 10 Titanium 1, 5, 10, 15, 20

20、 Copper 1, 10, 25, 50 Steel, Corrosion and Heat Resistant Alloys and Refractory Alloys 1-1/2, 2-1/2, 10, 12, 15, 25, 30 35, 44, 50, 60 TABLE 1B - SPOOLED WIRE WEIGHT, SI UNITS Alloy Base Net Weight, Kilograms Aluminum 0.45, 2.3, 4.5, 5.7, 6.8 Magnesium 0.3, 0.5, 4.5 Titanium 0.5, 2.2, 4.5, 6.8, 9.1

21、Copper 0.45, 4.5, 11.3, 22.7 Steel, Corrosion and Heat Resistant Alloys and Refractory Alloys 0.7, 1.1, 4.5, 5.5, 6.8, 11.3, 13.6, 15.9, 20, 22.7, 27.2 3.3.3 Exterior shipping containers of cut lengths shall contain approximately 5, 10, 50, 60, or 100 pounds (2.3, 4.5, 22.7, 27.2, or 45.3), as order

22、ed. 3.3.4 Containers of wire shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the wire to ensure carrier acceptance and safe delivery. 3.3.5 For direct U.S. Milit

23、ary procurement, packaging shall be in accordance with MIL-W-10430, Commercial Level, unless Level A is specified in the request for procurement. 3.4 Marking Each length of wire shall be marked in accordance with AMS2816, AMS2819 or other method acceptable to the purchaser. Interior containers of sp

24、ools and cut lengths and all exterior shipping containers shall be marked as follows: 3.4.1 Interior containers shall be permanently and legibly marked with not less than the following information; for containers of cut lengths, the information may appear on an attached label: WIRE, WELDING WIRE SPE

25、CIFICATION NUMBER (and revision letter if any) SIZE QUANTITY HEAT NUMBER (If applicable) MANUFACTURERS IDENTIFICATION 3.4.2 Exterior containers shall be permanently and legibly marked with not less than the following information: WIRE, WELDING WIRE SPECIFICATION NUMBER (and revision letter if any) S

26、IZE QUANTITY HEAT NUMBER (If applicable) PURCHASE ORDER NUMBER MANUFACTURERS IDENTIFICATION PACKAGED PER AMS2813 SAE INTERNATIONAL AMS2813G Page 4 of 4 4. QUALITY ASSURANCE PROVISIONS Not applicable. 5. PREPARATION FOR DELIVERY See Section 3. 6. ACKNOWLEDGMENT Not applicable. 7. REJECTIONS Wire not

27、packaged and marked in accordance with this specification, or with modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have

28、 been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 Dimens

29、ions and properties in inch/pound units and the Fahrenheit temperatures are primary: dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.3 Terms used in AMS are clarified in ARP1917, 8.4 Packaging meeting the requirements of this specification has been classified under Federal Supply Classification (FSC) 3439. PREPARED BY AMS COMMITTEE “B“