SAE AMS 3040D-2008 Magnetic Particles Nonfluorescent Dry Method《非荧光磁性粒子用干法》.pdf

1、AEROSPACE MATERIAL SPECIFICATION AMS3040 REV. D Issued 1974-03 Revised 2008-11 Reaffirmed 2014-08 Superseding AMS3040C Magnetic Particles, Nonfluorescent Dry Method RATIONALE AMS3040D has been reaffirmed to comply with the SAE five year review policy. _ SAE Technical Standards Board Rules provide th

2、at: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” S

3、AE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrie

4、val system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: Custome

5、rServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS3040D 1. SCOPE 1.1 Form This specification covers nonfluorescent, magnetic particles having black, red, gray, or other color,

6、as specified, supplied in the form of dry powders. 1.2 Application This product is used typically as an inspection medium in a dry magnetic particle inspection process in accordance with ASTM E 1444, but usage is not limited to such application. 1.3 Safety - Hazardous Materials While the materials,

7、methods, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use. It is the sole responsibility of the user to ensure familiarity with the safe and proper u

8、se of any hazardous materials and to take necessary precautionary measures to ensure the health and safety of all personnel involved. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified he

9、rein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from

10、 SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. AS5282 Tool Steel Ring for Magnetic Particle Inspection SAE INTERNATIONAL AMS3040D Page 2 of 5 2.2 ASTM Publications Available from ASTM Intern

11、ational, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM B 214 Sieve Analysis of Granular Metal Powders ASTM E 1444 Magnetic Particle Examination 3. TECHNICAL REQUIREMENTS 3.1 Material The product shall be composed of durable nonfluoresce

12、nt magnetic particles suitable for use in the dry magnetic particle inspection process in accordance with ASTM E 1444 and which may have been treated to attain the color specified. 3.2 Properties The product shall conform to the following requirements; tests shall be performed on the product supplie

13、d and in accordance with specified test procedures: 3.2.1 Contamination The dry powder shall show no evidence of foreign material or agglomeration, determined by visual examination during the tests to determine other characteristics of the product. 3.2.2 Color The product shall be black, red, gray,

14、or other color, as specified, determined by applying the dry powder onto white paper at least 8-1/2 x 11 inches (216 x 279 mm), completely covering an area not less than 4 inches (102 mm) in diameter. The color shall be observed under a white light of not less than 100 foot-candles (1000 lx) at the

15、examining surface. 3.2.3 Particle Size The magnetic particles shall be of such size that not less than 98% by weight shall pass through a U.S. Standard No. 80 screen/sieve, determined in accordance with ASTM B 214. Determine the dry weight of the residual particulate material not passing through the

16、 screen/sieve as related to the original weight of the sample, expressed in percent. 3.2.4 Sensitivity The product shall provide indications of at least the first eight holes of the test ring specimen of 4.3.1.2 when tested as follows: 3.2.4.1 Place the ring on a 1-inch (25-mm) diameter copper bar a

17、nd circularly magnetize in a standard magnetic particle inspection unit by passing 2500 amperes of direct current through the bar. While the current is flowing, apply approximately 1.0 gram of fresh dry powder that has passed the contamination test, using a suitable squeeze-bulb or shaker applicator

18、 Examine the ring under white light of not less than 100 foot-candles (1000 lx) at the examining surface. SAE INTERNATIONAL AMS3040D Page 3 of 5 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The manufacturer of the product shall supply all samples for manufacturers tests and sha

19、ll be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to the specified requirements. 4.2 Classification of Tests All technical requirements are acceptance tests

20、and preproduction tests and shall be performed prior to or on the initial shipment of magnetic particles to a purchaser, on each lot, when a change in ingredients and/or processing requires reapproval as in 4.4.2, and when purchaser deems confirmatory testing to be required. 4.3 Sampling and Testing

21、 4.3.1 For Acceptance Tests Sufficient powder shall be taken at random from each lot to perform all required tests. The number of determinations for each requirement shall be as specified in the applicable test procedure or, if not specified therein, not less than three. 4.3.1.1 A lot shall be all p

22、owder produced in a single production run, from the same batch of raw materials under the same fixed conditions, and presented for manufacturers inspection at one time. 4.3.1.2 Sensitivity Test Ring Shall be in accordance with AS5282. 4.3.2 For Preproduction Tests Shall be acceptable to purchaser. 4

23、4 Approval 4.4.1 Sample powder shall be approved by purchaser before powder for production use is supplied, unless such approval be waived by purchaser. Results of tests on production powder shall be equivalent to those on the approved sample. 4.4.2 Manufacturer shall use ingredients, manufacturing

24、 procedures, processes, and methods of inspection on production powder that are essentially the same as those used on the approved sample. If necessary to make any changes in ingredients, processing techniques, or manufacturing procedures, manufacturer shall submit for reapproval a statement of the

25、proposed changes in ingredients and/or processing and, when requested, sample powder. Production powder shall not be shipped prior to receipt of reapproval. 4.5 Reports The vendor of the product shall furnish with each shipment a report showing the results of tests to determine conformance to the ac

26、ceptance test requirements and stating that the product conforms to the other technical requirements. This report shall include the purchase order number, lot number, AMS3040D, date of manufacture, and quantity. SAE INTERNATIONAL AMS3040D Page 4 of 5 4.6 Resampling and Retesting If any sample used i

27、n the above tests fails to meet the specified requirements, disposition of the product may be based on the results of testing three additional samples for each original nonconforming sample. Failure of any retest sample to meet the specified requirements shall be cause for rejection of the product r

28、epresented. Results of all tests shall be reported. 5. PREPARATION FOR DELIVERY A lot of magnetic particles may be packaged in small quantities and delivered under the basic lot approval provided lot identification is maintained. 5.1 Packaging and Identification 5.1.1 Dry magnetic particles shall be

29、 in packaged containers of a type and size acceptable to purchaser. 5.1.2 Each package or container shall be legibly identified with a durable label providing not less than the following information: MAGNETIC PARTICLES, NONFLUORESCENT, DRY METHOD AMS3040D COLOR_ MANUFACTURERS IDENTIFICATION_ DATE OF

30、 MANUFACTURE* _ LOT NUMBER _ QUANTITY _ MANUFACTURERS INSTRUCTIONS FOR USE*_ APPROPRIATE WARNINGS OR PRECAUTIONARY NOTICES _ * May be included in manufacturers identification or lot number. * May be on a separate sheet. 5.1.3 Individual packages or containers shall be packed in an exterior shipping

31、container capable of protecting the product, during shipment and storage, against damage from exposure to moisture, weather, or any other normal hazard. 5.1.4 Containers of the product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and r

32、egulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Magne

33、tic particles not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. SAE INTERNATIONAL AMS3040D Page 5 of 5 8. NOTES 8.1 A change bar ( l ) located in the left margin is for the convenience of the user in locating areas where technical revisi

34、ons, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain ed

35、itorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.4 Purchase documents should specify not less than the following: AMS3040D Size and type of containers desired Quantity of product desired. PREPARED BY AMS COMMITTEE “K”