SAE AMS 3194E-2014 Silicone Rubber Sponge Closed Cell Firm Extreme Low Temperature《坚定的极端低温闭孔硅橡胶海绵》.pdf

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2014 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS3194E AEROSPACE MATERIAL SPECIFICATION AMS3194 REV. E Issued 1968-05 Reaffirme

5、d 2001-04 Revised 2014-05 Superseding AMS3194D Silicone Rubber Sponge Closed Cell, Firm, Extreme Low Temperature RATIONALE This document is being revised through a limited scope ballot to remove incorrect paragraph references. 1. SCOPE 1.1 Form This specification covers a silicone rubber sponge in t

6、he form of sheet, strip, extrusions, and molded shapes. 1.2 Application This sponge has been used typically for general applications requiring closed-cell, firm sponge rubber that will be flexible from -166 to +401 F (-110 to +205 C) but usage is not limited to such applications. Compression set may

7、 be high at the higher temperature. 1.3 Safety - Hazardous Materials While the materials, methods, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use.

8、It is the sole responsibility of the user to ensure familiarity with the safe and proper use of any hazardous materials and to take necessary precautionary measures to ensure the health and safety of all personnel involved. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on th

9、e date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified,

10、the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. AMS2810 Identification and Packaging, Elastomeric Pro

11、ducts SAE INTERNATIONAL AMS3194E Page 2 of 5 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM D 746 Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Imp

12、act ASTM D 1056 Standard Specification for Flexible Cellular Materials-Sponge or Expanded Rubber 3. TECHNICAL REQUIREMENTS 3.1 Material Shall be a compound, based on a silicone rubber, suitably cured to produce a product meeting the requirements of 3.2 and 3.3. 3.2 Finish The top and bottom surfaces

13、 of sheet and strip and the exterior surfaces of molded parts and extrusions (except ends) shall have a natural finish. 3.3 Properties The product shall conform to the requirements shown in Table 1, tests shall be performed on the product supplied and in accordance with ASTM D 1056, except as otherw

14、ise specified herein: TABLE 1 - PROPERTIES Paragraph Test Requirement Test Method 3.3.1 3.3.2 3.3.2.1 3.3.2.2 3.3.3 3.3.3.1 3.3.4 Compression-Deflection Density, max Nominal Thickness Under 0.25 inch (6.35 mm) 0.25 inch (6.35 mm) and over Compression Set: Percent of Original Deflection, max Brittlen

15、ess Temperature, max 12 to 20 psi (83 to 138 kPa) 0.030 pounds/cubic inch (0.83 g/cm) 0.025 pounds/cubic inch (0.69 g/cm) 60% -103 F (-75 C) 25 C 5 (77 F 9) 100 C 1 (212 F 2) 22 hours 0.2 ASTM D 746 3.4 Quality The product, as received by purchaser, shall be uniform in quality and condition, smooth,

16、 as free from foreign materials as commercially practicable, and free from imperfections detrimental to usage of the product. 3.5 Tolerances Shall be as shown in Table 2 and Table 3; measurements shall be made in accordance with ASTM D 1056: SAE INTERNATIONAL AMS3194E Page 3 of 5 3.5.1 Sheet and Str

17、ip 3.5.1.1 Thickness Shall be as shown in Table 2. TABLE 2A - TOLERANCES, INCH/POUND UNITS Nominal Thickness Inch Tolerance Inch Plus Tolerance Inch Minus Up to 0.063, inclusive Over 0.063 to 0.188, inclusive Over 0.188 to 0.313, inclusive Over 0.313 to 0.500, inclusive Over 0.500 to 0.750, inclusiv

18、e Over 0.750 0.030 0.030 0.050 0.060 0.090 0.120 0.016 0.030 0.030 0.060 0.090 0.120 TABLE 2B - TOLERANCES, SI UNITS Nominal Thickness Millimeters Tolerance Millimeters Plus Tolerance Millimeters Minus Up to 1.60, inclusive Over 1.60 to 4.78, inclusive Over 4.78 to 7.95, inclusive Over 7.95 to 12.70

19、, inclusive Over 12.70 to 19.05, inclusive Over 19.05 0.76 0.76 1.27 1.52 2.29 3.05 0.41 0.76 0.76 1.52 2.29 3.05 3.5.1.2 Length and Width Shall be as shown in Table 3. TABLE 3A - TOLERANCES, INCH/POUND UNITS Nominal Length and Width Inches Tolerance Inch Plus and Minus Up to 6, inclusive Over 6 to

20、18, inclusive Over 18 0.125 0.250 0.375 TABLE 3B - TOLERANCES, SI UNITS Nominal Length and Width Millimeters Tolerance Millimeters Plus and Minus Up to 152, inclusive Over 152 to 457, inclusive Over 457 3.18 6.35 9.52 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The manufacturer

21、 of sponge shall supply all samples and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that sponge conforms to specified requirements SAE INTERNATIONAL AMS3194E Page 4 of 5 4.2

22、Classification of Tests All technical requirements are acceptance tests and preproduction tests and shall be performed prior to or on the initial shipment of sponge to a purchaser, on each lot, when a change in ingredients and/or processing requires reapproval as in 4.4.2, and when purchaser deems c

23、onfirmatory testing to be required. 4.3 Sampling and Testing Shall be as follows: 4.3.1 For Acceptance Tests Sufficient sponge shall be taken at random from each lot to perform all required tests. The number of determinations for each requirement shall be as specified in the applicable test procedur

24、e or, if not specified therein, not less than three. 4.3.1.1 A lot shall be all sponge from the same batch of compound, processed in one continuous production run, and presented for manufacturers inspection at one time. 4.3.1.2 A batch shall be the quantity of compound run through a mill or mixer at

25、 one time. 4.3.1.3 A statistical sampling plan, acceptable to purchaser, may be used in lieu of sampling as in 4.3.1 and the report of 4.5 shall state that such plan was used. 4.3.2 For Preproduction Tests Shall be acceptable to purchaser. 4.4 Approval 4.4.1 Sample sponge shall be approved by purcha

26、ser before sponge for production use is supplied, unless such approval be waived by purchaser. Results of tests on production sponge shall be essentially equivalent to those on the approved sample. 4.4.2 Manufacturer shall use ingredients, manufacturing procedures, processes, and methods of inspecti

27、on on production sponge which are essentially the same as those used on the approved sample. If necessary to make any change in ingredients, in type of equipment for processing, or in manufacturing procedures, manufacturer shall submit for reapproval a statement of the proposed changes in ingredient

28、s and/or processing and, when requested, sample sponge. Production sponge made by the revised procedure shall not be shipped prior to receipt of reapproval. 4.5 Reports The supplier of sponge shall furnish with each shipment a report showing the results of tests to determine conformance to the techn

29、ical requirements. This report shall include the purchase order number, lot number, AMS3194E, manufacturers identification, form or part number, and quantity. 4.6 Resampling and Retesting If any specimen used in the above tests fails to meet the specified requirements, disposition of the sponge may

30、be based on the results of testing three additional specimens from the same lot for each original nonconforming specimen. Failure of any retest specimen to meet the specified requirements shall be cause for rejection of the sponge represented. Results of all tests shall be reported. 5. PREPARATION F

31、OR DELIVERY 5.1 Identification and Packaging Shall be in accordance with AMS2810. SAE INTERNATIONAL AMS3194E Page 5 of 5 5.1.1 A lot of sponge may be packaged in small quantities and delivered under the basic lot approval provided lot identification is maintained. 6. ACKNOWLEDGMENT A supplier shall

32、mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Sponge not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 A change bar (|) located in the left

33、margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change ba

34、rs and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.3 Purchase documents should specify not less than the following: AMS3194E Form and size or part number of sponge desired Quantity of sponge desired. PREPARED BY AMS COMMITTEE “CE“