SAE AMS 3196F-1992 Sponge Silicone Rubber Closed Cell Firm《坚固闭孔硅酮海绵橡胶》.pdf

1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirelyvoluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefro

2、m, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.Copyright 2001 Society of Automotive Engineers, Inc.All rights reserved. Printed in U.S.

3、A.QUESTIONS REGARDING THIS DOCUMENT: (724) 772-7161 FAX: (724) 776-0243TO PLACE A DOCUMENT ORDER: (724) 776-4970 FAX: (724) 776-0790SAE WEB ADDRESS: http:/www.sae.org400 Commonwealth Drive, Warrendale, PA 15096-0001AEROSPACE MATERIAL SPECIFICATIONAMS 3196FIssued JUL 1957Revised JAN 1992Reaffirmed OC

4、T 2001Superseding AMS 3196ESponge, Silicone RubberClosed Cell, Firm1. SCOPE:1.1 Form: This specification covers a silicone rubber sponge in the form of sheet, strip, extrusions, and molded shapes.1.2 Application: This product has been used typically for general applications requiring closed-cell, fi

5、rm sponge rubber that will be flexible from -75 to +205 C (-103 to +401 F), but usage is not limited to such applications. Compression set may be high at the higher temperature.1.3 Safety - Hazardous Materials: While the materials, methods, applications, and processes described or referenced in this

6、 specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use. It is the sole responsibility of the user to ensure familiarity with the safe and proper use of any hazardous materials and to take necessary precautionary me

7、asures to ensure the health and safety of all personnel involved.2. APPLICABLE DOCUMENTS: The following publications form a part of this specification to the extent specified herein. The latest issue of SAE publications shall apply. The applicable issue of other publications shall be the issue in ef

8、fect on the date of the purchase order.2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001.AMS 2810 Identification and Packaging, Elastomeric ProductsCopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking

9、permitted without license from IHS-,-AMS 3196F SAE AMS 3196F- 2 -2.2 ASTM Publications: Available from ASTM, 100 Barr Harbor, West Conshohocken, PA 19428-2959.ASTM D 746 Brittleness Temperature of Plastics and Elastomers by ImpactASTM D 1056 Flexible Cellular Materials - Sponge or Expanded Rubber3.

10、TECHNICAL REQUIREMENTS: 3.1 Material: Shall be a compound, based on a silicone rubber, suitably cured to produce a product meeting the requirements of 3.2 and 3.3.3.2 Finish: The top and bottom surfaces of sheet and strip and the exterior surfaces of molded parts and extrusions (except ends) shall h

11、ave a natural finish.3.3 Properties: The product shall conform to the requirements shown in Table 1; tests shall be performed on the product supplied and in accordance with ASTMD1056, except as otherwise specified herein:TABLE 1 - PropertiesParagraph Test Requirement Test Method3.3.1 Compression-Def

12、lection 12 - 20 psi(83 - 138 kPa)25 C 5(77 F 9)3.3.2 Density, maximumNominal Thickness3.3.2.1 Under 0.25 inch (6.35 mm) 0.030 pounds/cubic inch(830 kg/m3)3.3.2.2 0.25 inch (6.35 mm) and over 0.025 pounds/cubic inch(692 kg/m3)3.3.3 Compression Set: 100 C 1(212 F 2)3.3.3.1 Percent of OriginalDeflectio

13、n, maximum 60%22 hours 0.23.3.4 Brittleness Temperature,maximum-55 C (-67 F) ASTM D 746Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-AMS 3196F SAE AMS 3196F- 3 -3.3.5 Weathering: When specified, the

14、product shall have weather resistance acceptable to purchaser, determined by a procedure agreed upon by purchaser and vendor.3.3.6 Corrosion: The product shall not have a corrosive effect on other materials when exposed to conditions normally encountered in service determined by a procedure agreed u

15、pon by purchaser and vendor. Discoloration of metal shall not be considered objectionable. Standards for acceptance shall be as agreed upon by purchaser and vendor.3.4 Quality: The product, as received by purchaser, shall be uniform in quality and condition, smooth, as free from foreign materials as

16、 commercially practicable, and free from imperfections detrimental to usage of the product.3.5 Tolerances: Shall be as shown in Table 2 and Table 3; measurements shall be made in accordance with ASTM D 1056:3.5.1 Sheet and Strip: 3.5.1.1 Thickness: TABLE 2A - Thickness Tolerances, Inch/Pound UnitsNo

17、minal ThicknessInchToleranceInchplusToleranceInchminusUp to 0.063 incl 0.030 0.016Over 0.063 to 0.188 incl 0.030 0.030Over 0.188 to 0.313 incl 0.050 0.030Over 0.313 to 0.500 incl 0.060 0.060Over 0.500 to 0.750 incl 0.090 0.090Over 0.750 0.120 0.120TABLE 2B - Thickness Tolerances, SI UnitsNominal Thi

18、cknessMillimetersToleranceMillimetersplusToleranceMillimetersminusUp to 1.60 incl 0.76 0.41Over 1.60 to 4.78 incl 0.76 0.76Over 4.78 to 7.95 incl 1.27 0.76Over 7.95 to 12.70 incl 1.52 1.52Over 12.70 to 19.05 incl 2.29 2.29Copyright SAE International Provided by IHS under license with SAENot for Resa

19、leNo reproduction or networking permitted without license from IHS-,-AMS 3196F SAE AMS 3196F- 4 -3.5.1.2 Length and Width: 4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: The vendor of sponge shall supply all samples for vendors tests and shall be responsible for performing all r

20、equired tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the sponge conforms to the requirements of this specification.4.2 Classification of Tests: Tests for all technical requirements are acceptance tests and preproduction tests a

21、nd shall be performed prior to or on the initial shipment of sponge to a purchaser, on each lot, when a change in ingredients and/or processing requires reapproval as in 4.4.2, and when purchaser deems confirmatory testing to be required.4.2.1 For direct U.S. Military procurement, substantiating tes

22、t data and, when requested, preproduction test material shall be submitted to the cognizant agency as directed by the procuring activity, contracting officer, or request for procurement.4.3 Sampling and Testing: Over 19.05 3.05 3.05TABLE 3A - Length and Width Tolerances, Inch/Pound UnitsNominal Leng

23、th and WidthInchesTolerance, Inchplus and minusUp to 6, incl 0.125Over 6 to 18, incl 0.250Over 18 0.375TABLE 3B - Length and Width, Tolerances, SI UnitsNominal Length and WidthMillimetersTolerance, Millimetersplus and minusUp to 152, incl 3.18Over 152 to 457, incl 6.35Over 457 9.52TABLE 2B - Thickne

24、ss Tolerances, SI UnitsCopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-AMS 3196F SAE AMS 3196F- 5 -Shall be as follows:4.3.1 For Acceptance Tests: Sufficient sponge shall be taken at random from each l

25、ot to perform all required tests. The number of determinations for each requirement shall be as specified in the applicable test procedure or, if not specified therein, not less than three.4.3.1.1 A lot shall be all sponge produced from the same batch of compound processed in one continuous producti

26、on run and presented for vendors inspection at one time. A lot shall not exceed 500 pounds (227kg) and may be packaged in smaller quantities and delivered under the basic lot approval provided lot identification is maintained.4.3.1.2 A batch shall be the quantity of compound run through a mill or mi

27、xer at one time.4.3.1.3 When a statistical sampling plan has been agreed upon by purchaser and vendor, sampling shall be in accordance with such plan in lieu of sampling as in 4.3.1 and the report of 4.5 shall state that such plan was used.4.3.2 For Preproduction Tests: As agreed upon by purchaser a

28、nd vendor.4.4 Approval: 4.4.1 Sample sponge shall be approved by purchaser before sponge for production use is supplied, unless such approval be waived by purchaser. Results of tests on production sponge shall be essentially equivalent to those on the approved sample.4.4.2 Vendor shall use ingredien

29、ts, manufacturing procedures, processes, and methods of inspection on production sponge which are essentially the same as those used on the approved sample sponge. If necessary to make any change in ingredients, in type of equipment for processing, or in manufacturing procedures, vendor shall submit

30、 for reapproval a statement of the proposed changes in ingredients and/or processing and, when requested, sample sponge. Production sponge made by the revised procedure shall not be shipped prior to receipt of reapproval.4.5 Reports: The vendor of sponge shall furnish with each shipment a report sho

31、wing the results of tests to determine conformance to the technical requirements. This report shall include the purchase order number, vendors compound number, lot number, AMS 3196F, form or part number, and quantity.4.6 Resampling and Retesting: If any specimen used in the above tests fails to meet

32、 the specified requirements, disposition of the sponge may be based on the results of testing three additional specimens for each original nonconforming specimen. Failure of any retest specimen to meet the specified requirements shall be cause for rejection of the sponge represented. Results of all

33、tests shall be reported.5. PREPARATION FOR DELIVERY: Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-AMS 3196F SAE AMS 3196F- 6 -5.1 Identification and Packaging: Shall be in accordance with AMS 2810.C

34、opyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-AMS 3196F SAE AMS 3196F- 7 -6. ACKNOWLEDGMENT: A vendor shall mention this specification number and its revision letter in all quotations and when acknowl

35、edging purchase orders.7. REJECTIONS: Sponge not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection.8. NOTES: 8.1 A change bar ( l ) located in the left margin is for the convenience of the user in locating areas where technical revisions, not

36、 editorial changes, have been made to the previous issue of this specification. An (R) symbol to the left of the document title indicates a complete revision of the specification, including technical revisions. Change bars and (R) are not used in original publications, nor in specifications that con

37、tain editorial changes only.8.2 Dimensions and properties in inch/pound units and the Celsius temperatures are primary; dimensions and properties in SI units and the Fahrenheit temperatures are shown as the approximate equivalents of the primary units and are presented only for information.8.3 For d

38、irect U.S. Military procurement, purchase documents should specify not less than the following:Title, number, and date of this specificationForm and size or part number of sponge desiredQuantity of sponge desiredAcceptance standards and test methods for weathering (See 3.3.5) and corrosion (See 3.3.

39、6)Level A packaging, if required (See AMS 2810).8.4 Similiar Specifications: MIL-R-46089 is listed for information only and shall not be construed as an acceptable alternate unless all requirements of this AMS are met.8.5 Sponge meeting the requirements of this specification has been classified unde

40、r Federal Supply Classification (FSC) 9320.8.6 Key Words: Silicone rubber, closed cell sponge, sheet, strip, extrusions, shapesPREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “CE”Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-