SAE AMS 3654C-1993 Tubing Electrical Insulation Light Wall Extruded Polytetrafluoroethylene (PTFE)《挤塑聚四氟乙烯电绝缘薄壁管》.pdf

1、SAE-AMS3654ADOPTION NOTICESAE-AMS3654, “INSULATION, ELECTRICAL, TUBING, LIGHT WALL,EXTRUDED POLYTETRAFLUOROETHYLENE (PTFE)“, was adopted on20-OCT-88 for use by the Department of Defense (DoD). Proposedchanges by DoD activities must be submitted to the DoD AdoptingActivity: Commander, Naval Air Warfa

2、re Center, Aircraft Division,Code 414100B120-3, Highway 547, Lakehurst, NJ 08733-5100. Copiesof this document may be purchased from the Society of AutomotiveEngineers 400 Commonwealth Drive Warrendale, Pennsylvania, UnitedStates, 15096-0001. http:/www.sae.org/_Custodians: Adopting Activity:Navy - AS

3、Army - MRNavy - ASAir Force - 11Reviewer Activities:Army - ARDLA - GSFSC 5970DISTRIBUTION STATEMENT A: Approved for public release; distributionis unlimited.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IH

4、S-,-SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and enginee ring sciences. The use of this report is entirelyvoluntary, and its applicability and suitability for any particular use, including any patent infringement arising the

5、refrom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invit es your written comments and suggestions.Copyright 1999 Society of Automotive Engineers, Inc.All rights reserved. Printed i

6、n U.S.A.QUESTIONS REGARDING THIS DOCUMENT: (724) 772-7154 FAX: (724) 776-0243TO PLACE A DOCUMENT ORDER: (724) 776-4970 FAX: (724) 776-0790SAE WEB ADDRESS: http:/www.sae.org400 Commonwealth Drive, Warrendale, PA 15096-0001AEROS PACE MATERIAL SPECIFIC ATIONSubmitted for recognition as an American Nati

7、onal StandardAMS 3654CIssued JAN 1961Revised JAN 1993Reaffirmed JAN 1999Superseding AMS 3654BTubing, Electrical InsulationLight Wall, Extruded Polytetrafluoroethylene (PTFE)FOREWORDChanges in this Reaffirm are format/editorial only.1. SCOPE:1.1 Form: This specification covers extruded polytetrafluor

8、oethylene (PTFE) in the form of flexible tubing.1.2 Application: This tubing has been used typically for electrical insulating sheath up to 260 C (500 F), but usage is not limited to such applications.1.3 Safety - Hazardous Materials: While the materials, methods, applications, and processes describ

9、ed or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use. It is the sole responsibility of the user to ensure familiarity with the safe and proper use of any hazardous materials and to take ne

10、cessary precautionary measures to ensure the health and safety of all personnel involved.2. APPLICABLE DOCUMENTS: The following publications form a part of this specification to the extent specified herein. The applicable issue of referenced publications shall be the issue in effect on the date of t

11、he purchase order.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-AMS 3654C SAE AMS 3654C- 2 -2.1 ASTM Publications: Available from ASTM, 100 Barr Harbor, West Conshohocken, PA 19428-2959.ASTM D 876 Te

12、sting Nonrigid Vinyl Chloride Polymer Tubing Used for Electrical InsulationASTM D 1675 Testing Polytetrafluoroethylene Tubing2.2 U.S. Government Publications: Available from DODSSP, Subscription Services Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.MIL-STD-104 Limit for Electri

13、cal Insulation ColorMIL-STD-2073-1 DOD Materiel, Procedures for Development and Application of Packaging Requirements3. TECHNICAL REQUIREMENTS: 3.1 Material: Shall be flexible tubing made from extruded virgin polytetrafluoroethylene, free from contamination and from foreign, reground, and scrap mate

14、rial.3.2 Color: Tubing shall be natural in color, ranging from colorless translucent to semi-opaque white. When ordered in colors, the colors shall be in accordance with MIL-STD-104 or as agreed upon by purchaser and vendor.3.3 Properties: Tubing shall conform to the requirements shown in Table 1; t

15、ests shall be performed on the tubing supplied and in accordance with specified ASTM methods, insofar as practicable:Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-AMS 3654C SAE AMS 3654C- 3 -3.4 Qual

16、ity: Tubing, as received by purchaser, shall be uniform in quality and condition, smooth, and free from foreign materials and from imperfections detrimental to usage of the tubing.TABLE 1 - PropertiesParagraph Property Requirement Test Method3.3.1 Tensile Strength at 200% Elongation2500 to 6000 psi(

17、17.2 to 41.4 MPa)ASTM D 87625 C 1(77 F 2)3.3.2 Elongation, minimum 200% ASTM D 87625 C 1(77 F 2)3.3.3 Dielectric Breakdown Voltage,minimum averageNominal NominalWall Thickness Wall ThicknessInch Millimeter0.006 0.150.008 0.200.010 0.250.012 0.300.015 - 0.020 0.38 - 0.518,000 volts10,000 volts11,000

18、volts12,000 volts14,000 voltsASTM D 87625 C 1(77 F 2)3.3.4 Specific Gravity 2.14 to 2.21 ASTM D 16753.3.5 Strain Relief (shrinkage),maximum 1.0%ASTM D 1675300 C 3(572 F 5)3.3.6 Volatile Loss, maximum 0.05% ASTM D 1675300 C 3(572 F 5)3.3.7 Mandrel Bend (dielectricbreakdown reduction),maximum 25%ASTM

19、D 1675Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-AMS 3654C SAE AMS 3654C- 4 -3.5 Sizes and Tolerances: Shall be as shown in Table 2; tolerances apply at 20to 30 C (68 to 86 F), measured in accorda

20、nce with ASTMD 1675.4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: The vendor of tubing shall supply all samples for vendors tests and shall be responsible for performing all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed ne

21、cessary to ensure that the tubing conforms to the requirements of this specification.4.2 Classification of Tests: 4.2.1 Acceptance Tests: Tests for the requirements shown in Table 3 are acceptance tests and shall be performed on each lot.TABLE 3 - Acceptance TestsRequirement Paragraph ReferenceTensi

22、le Strength 3.3.1Elongation 3.3.2Dielectric Breakdown Voltage 3.3.3Specific Gravity 3.3.4Sizes and Tolerances 3.5Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-AMS 3654C SAE AMS 3654C- 5 -TABLE 2A - S

23、izes and Tolerances, Inch/Pound UnitsSizeNo.ID, InchNominalID, InchMinimumID, InchMaximumWallThicknessInchNominalWall ThicknessToleranceInchplus and minus30 0.012 0.010 0.015 0.006 0.00228 0.015 0.013 0.018 0.006 0.00226 0.018 0.016 0.021 0.006 0.00224 0.022 0.020 0.026 0.008 0.00222 0.028 0.026 0.0

24、32 0.008 0.00220 0.034 0.032 0.038 0.008 0.00219 0.038 0.036 0.042 0.008 0.00218 0.042 0.040 0.046 0.008 0.00217 0.047 0.045 0.052 0.008 0.00216 0.053 0.051 0.058 0.008 0.00215 0.059 0.057 0.065 0.008 0.00214 0.066 0.064 0.072 0.008 0.00213 0.076 0.072 0.081 0.008 0.00212 0.085 0.081 0.091 0.008 0.0

25、0211 0.095 0.091 0.101 0.008 0.00210 0.106 0.102 0.112 0.008 0.0029 0.118 0.114 0.124 0.008 0.0021/8 - 0.125 0.139 0.008 0.0028 0.133 0.129 0.139 0.008 0.0027 0.148 0.144 0.155 0.008 0.0026 0.166 0.162 0.174 0.010 0.0035 0.186 0.182 0.195 0.010 0.0034 0.208 0.204 0.218 0.010 0.0033 0.234 0.229 0.244

26、 0.010 0.0031/4 - 0.250 0.260 0.010 0.0032 0.263 0.258 0.273 0.010 0.0031 0.294 0.289 0.305 0.010 0.0035/16 - 0.313 0.334 0.012 0.0030 0.330 0.325 0.342 0.012 0.0033/8 - 0.375 0.394 0.015 0.0051/2 - 0.500 0.520 0.018 0.0055/8 - 0.625 0.650 0.020 0.0053/4 - 0.750 0.775 0.020 0.005Copyright SAE Intern

27、ational Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-AMS 3654C SAE AMS 3654C- 6 -TABLE 2B - Sizes and Tolerances, SI UnitsSizeNo.IDMillimetersNominalIDMillimetersMinimumIDMillimetersMaximumWallThicknessMillimeterNominalWall Th

28、icknessToleranceMillimeterplus and minus30 0.30 0.25 0.38 0.15 0.0528 0.38 0.33 0.46 0.15 0.0526 0.46 0.41 0.53 0.15 0.0524 0.56 0.51 0.60 0.20 0.0522 0.71 0.60 0.81 0.20 0.0520 0.86 0.81 0.96 0.20 0.0519 0.96 0.91 1.07 0.20 0.0518 1.07 1.02 1.17 0.20 0.0517 1.19 1.14 1.32 0.20 0.0516 1.35 1.30 1.47

29、 0.20 0.0515 1.50 1.45 1.65 0.20 0.0514 1.68 1.62 1.83 0.20 0.0513 1.93 1.83 2.06 0.20 0.0512 2.16 2.06 2.31 0.20 0.0511 2.41 2.31 2.56 0.20 0.0510 2.69 2.59 2.84 0.20 0.059 3.00 2.90 3.15 0.20 0.051/8 - 3.18 3.53 0.20 0.058 3.38 3.28 3.53 0.20 0.057 3.76 3.66 3.94 0.20 0.056 4.22 4.11 4.42 0.25 0.0

30、85 4.72 4.62 4.95 0.25 0.084 5.28 5.18 5.54 0.25 0.083 5.93 5.82 6.20 0.25 0.081/4 - 6.35 6.60 0.25 0.082 6.68 6.55 6.93 0.25 0.081 7.47 7.34 7.75 0.25 0.085/16 - 7.95 8.48 0.30 0.080 8.38 8.26 8.69 0.30 0.083/8 - 9.52 10.01 0.38 0.131/2 - 12.70 13.21 0.46 0.135/8 - 15.88 16.51 0.51 0.133/4 - 19.05

31、19.68 0.51 0.13Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-AMS 3654C SAE AMS 3654C- 7 -4.2.2 Preproduction Tests: Tests for all technical requirements are preproduction tests and shall be performed

32、 prior to or on the initial shipment of tubing to a purchaser, when a change in ingredients and/or processing requires reapproval as in 4.4.2, and when purchaser deems confirmatory testing to be required.4.2.2.1 For direct U.S. Military procurement, substantiating test data and, when requested, prep

33、roduction test material shall be submitted to the cognizant agency as directed by the procuring activity, contracting officer, or request for procurement.4.3 Sampling and Testing: Shall be as follows:4.3.1 For Acceptance Tests: Sufficient tubing shall be taken at random from each lot to perform all

34、required tests. The number of determinations for each requirement shall be as specified in the applicable test procedure or, if not specified therein, not less than three.4.3.1.1 When suitable test specimens cannot be cut from the tubing, a separate flat strip test sample shall be supplied upon requ

35、est. This strip shall be prepared from tubing 1.000 inch 0.063 (25.40 mm 1.60) in OD by 0.075inch0.008 (1.90mm0.20) in wall thickness, mechanically slit and flattened into a strip while being extruded, and cured in the same manner as production tubing.4.3.1.2 A lot shall be all tubing from the same

36、batch of compound processed in one continuous run and presented for vendors inspection at one time. An inspection lot shall not exceed 500 pounds (227 kg). 4.3.1.3 When a statistical sampling plan has been agreed upon by purchaser and vendor, sampling shall be in accordance with such plan in lieu of

37、 sampling as in 4.3.1 and the report of 4.5 shall state that such plan was used.4.3.2 For Preproduction Tests: As agreed upon by purchaser and vendor.4.4 Approval: 4.4.1 Sample tubing shall be approved by purchaser before tubing for production use is supplied, unless such approval be waived by purch

38、aser. Results of tests on production tubing shall be essentially equivalent to those on the approved sample.4.4.2 Vendor shall use ingredients, manufacturing procedures, processes, and methods of inspection on production tubing which are essentially the same as those used on the approved sample tubi

39、ng. If necessary to make any change in ingredients, in type of equipment for processing, or in manufacturing procedures, vendor shall submit for reapproval a statement of the proposed changes in ingredients and/or processing and, when requested, sample tubing. Production tubing made by the revised p

40、rocedure shall not be shipped prior to receipt of reapproval.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-AMS 3654C SAE AMS 3654C- 8 -4.5 Reports: The vendor of tubing shall furnish with each shipme

41、nt a report showing the results of tests to determine conformance to the acceptance test requirements and stating that the tubing conforms to the other technical requirements. This report shall include the purchase order number, lot number, AMS 3654C, vendors material designation, size, and quantity

42、.4.6 Resampling and Retesting: If any specimen used in the above tests fails to meet the specified requirements, disposition of the tubing may be based on the results of testing three additional specimens for each original nonconforming specimen. Failure of any retest specimen to meet the specified

43、requirements shall be cause for rejection of the tubing represented. Results of all tests shall be reported.5. PREPARATION FOR DELIVERY: 5.1 Identification: Each package shall be permanently and legibly marked with not less than AMS3654C, size, color, quantity, purchase order number, manufacturers i

44、dentification, and date of manufacture.5.2 Packaging: 5.2.1 Packaging shall be accomplished to ensure that the tubing, during shipment and storage, will not be permanently distorted and will be protected against damage from exposure to weather or any other normal hazard.5.2.1.1 Standard packages sha

45、ll contain quantities as agreed upon by purchaser and vendor.5.2.1.2 Packaging of special sizes and lengths shall be as agreed upon by purchaser and vendor.5.2.1.3 A lot of tubing may be packaged in small quantities and delivered under the basic lot approval provided lot identification is maintained

46、.5.2.2 Packages of tubing shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the tubing to ensure carrier acceptance and safe delivery. 5.2.3 For direct U. S. Milit

47、ary procurement, packaging shall be in accordance with MIL-STD-2073-1, Commercial Level, unless Level A is specified in the request for procurement. 6. ACKNOWLEDGMENT: A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders.Co

48、pyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-AMS 3654C SAE AMS 3654C- 9 -7. REJECTIONS: Tubing not conforming to this specification, or to modifications authorized by purchaser, will be subject to rej

49、ection.8. NOTES: 8.1 The change bar (|) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this specification. An (R) symbol to the left of the document title indicates a complete revision of the specification.8.2 Dimensions and propertie