SAE AMS 3704A-1993 Adhesive Contact Polychloroprene (CR) Rubber Resin Modified《改良树脂的接触聚氯丁橡胶胶粘剂》.pdf

1、_SAE Technical Standards Board Rules providHWKDW7KLVUHSRUWLVSXEOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQ LFDODQGHQJLQHHULQJVFLHQFHV7KHXVHRIWKLVUHSRUWL sentirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising thereIURPLVWKHVROHUHVSRQVLELOLW

2、RIWKHXVHUSAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2016 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in

3、a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790Email: Cus

4、tomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/AMS3704AAEROSPACEMATERIAL SPECIFICATIONAMS3704REV. AIssued 1985-07Revised 1993-10Reaffirmed 2016-09Superseding AMS3704Adhesive, C

5、ontactPolychloroprene (CR) Rubber, Resin ModifiedRATIONALEAMS3704A has been reaffirmed to comply with the SAE five-year review policy.1. SCOPE:1.1 Form:This specification covers a polychloroprene (CR) rubber, resin modified, solvent-type contact adhesive in the form of a liquid.1.2 Application:This

6、adhesive has been used typically for bonding leather or polyurethane foam liners in pilots flight helmets, bonding of fabric, plastic laminate, and wood surfaces to themselves or to each other, but usage is not limited to such applications.1.3 Safety-Hazardous Materials: While the materials, methods

7、, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use. It is the sole responsibility of the user to ensure familiarity with the safe and proper use of a

8、ny hazardous materials and to take necessary precautionary measures to ensure the health and safety of all personnel involved.2. APPLICABLE DOCUMENTS: The following publications form a part of this specification to the extent specified herein. The latest issue of SAE publications shall apply. The ap

9、plicable issue of other publications shall be the issue in effect on the date of the purchase order.2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001.AMS 2825 Material Safety Data SheetsAMS 3570 Foam, Flexible Polyurethane, Open Cell, Medium FlexibilityAMS 3

10、607 Plastic Sheet, Cotton Fabric Reinforced Phenol-Formaldehyde2.2 ASTM Publications: Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.ASTM D 297 Rubber Products - Chemical AnalysisASTM D 618 Conditioning Plastics and Electrical Insulating Materials for TestingASTM D 816

11、Testing Rubber CementsASTM D 1002 Strength Properties of Adhesives in Shear by Tension Loading (Metal-to-Metal)ASTM D 1084 Viscosity of AdhesivesASTM D 1183 Resistance of Adhesive to Cyclic Laboratory Aging ConditionsASTM D 1337 Storage Life of Adhesives by Consistency and Bond StrengthASTM D 1875 D

12、ensity of Adhesives in Fluid Form2.3 U. S. Government Publications: Available from DODSSP, Subscription Services Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.MIL-STD-2073-1 DOD Materiel, Procedures for Development and Application of Packaging Requirements3. TECHNICAL REQUIREMEN

13、TS: 3.1 Material: Shall consist of a polychloroprene (CR) rubber compound and a suitable resin dissolved in a solvent or solvent mixture. The product shall be free of ketones, halogenated hydrocarbons, benzene, and other solvents which have a deleterious effect on foamed polyurethanes.3.1.1 Shelf Li

14、fe: The adhesive, stored in airtight containers, shall meet the requirements of 3.2 after storage at not higher than 27 C (81 F) for up to 12 months from date of manufacture except that viscosity changes of 10% shall be acceptable.3.2 Properties: Adhesive shall conform to the requirements shown in T

15、able 1.SAE INTERNATIONAL AMS3704A Page 2 of 8_3.3 Quality: The adhesive, as received by purchaser, shall be uniform in quality and condition, and free from foreign materials and from other contaminants detrimental to usage of the adhesive.4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspe

16、ction: The manufacturer of the product shall supply all samples for required tests and shall be responsible for performing all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to the requirements of th

17、is specification.4.2 Classification of Tests: 4.2.1 Acceptance Tests: Tests for tensile shear strength before aging (3.2.4.1) are acceptance tests and shall be performed on each lot.TABLE 1 - PropertiesParagraph Property Requirement Test Method3.2.1 Density: 6.5 to 7.5pounds/gallon(0.78 to 0.90 kg/L

18、)ASTM D 18753.2.2 Viscosity 400 to 1500 centipoises(0.4 to 1.5 Pas)ASTM D 1084,Method B,No. 2Spindleat 20 rpm3.2.3 Ash Content, by Weight: 3.0 to 20% ASTM D 297,RefereeAsh Method3.2.4 Tensile Shear Strength:3.2.4.1 Before Aging, minimum: 150 psi (1.03 MPa) 4.5.13.2.4.2 After Aging, minimum: 200 psi

19、(1.38 MPa) 4.5.23.2.5 Bonding Range, minimum 60 minutes 4.5.33.2.6 Accelerated Aging:Permissible Viscosity Change 10%4.5.43.2.7 Freeze-Thaw Resistance:Permissible Viscosity Change 10%4.5.53.2.8 Nonvolatile Content, by weight: 18 to 25% 4.5.63.2.9 Polyurethane Foam Compatibility: No attack 4.5.7SAE I

20、NTERNATIONAL AMS3704A Page 3 of 8_4.2.2 Preproduction Tests: Tests for all technical requirements are preproduction tests and shall be performed prior to or on the first-article shipment of adhesive to a purchaser, when a change in ingredients and/or processing requires reapproval as in 4.4.2, and w

21、hen purchaser deems confirmatory testing to be required.4.2.2.1 For direct U. S. Military procurement, substantiating test data and, when requested, preproduction test material shall be submitted to the cognizant agency as directed by the procuring activity, contracting officer, or request for procu

22、rement.4.3 Sampling and Testing: Shall be as follows:4.3.1 For Acceptance Tests: Sufficient adhesive shall be taken at random from each lot to perform all required tests. The number of determinations for each requirement shall be as specified in the applicable test procedure or, if not specified the

23、rein, not less than three.4.3.1.1 A lot shall be all adhesive produced in a single production run from the same batches of raw materials and presented for manufacturers inspection at one time. A lot shall not exceed 1000 gallons (3785 L).4.3.1.2 When a statistical sampling plan has been agreed upon

24、by purchaser and manufacturer, sampling shall be in accordance with such plan in lieu of sampling as in 4.3.1 and the report of 4.6 shall state that such plan was used.4.3.2 For Preproduction Tests: As agreed upon by purchaser and manufacturer.4.4 Approval: 4.4.1 Sample adhesive shall be approved by

25、 purchaser before adhesive for production use is supplied, unless such approval be waived by purchaser. Results of tests on production adhesive shall be essentially equivalent to those on the approved sample.4.4.2 Manufacturer shall use ingredients, manufacturing procedures, processes, and methods o

26、f inspection on production adhesive which are essentially the same as those used on the approved sample. If necessary to make any change in ingredients, in type of equipment for processing, or in manufacturing procedures, manufacturer shall submit for reapproval a statement of the proposed changes i

27、n ingredients and/or processing and, when requested, sample adhesive. Production adhesive made by the revised procedure shall not be shipped prior to receipt of reapproval.4.5 Test Methods: Tests to determine conformance to requirements of this specification shall be conducted as specified in 3.2 an

28、d as follows:SAE INTERNATIONAL AMS3704A Page 4 of 8_4.5.1 Tensile Shear Strength, Before Aging: Shall be determined in accordance with ASTM D 1002 using specimens prepared from adherents cut from 1/4 inch (6.4 mm) nominal thickness, commercial grade A fir plywood, and 0.062 inch (1.6 mm) nominal thi

29、ckness AMS 3607 plastic laminate. Specimens shall be preconditioned in accordance with ASTM D 618. The value reported shall be the average shear value of not less than five specimens.4.5.2 Tensile Shear Strength, After Aging: Not less than five specimens prepared in accordance with 4.5.1 shall be ex

30、posed to aging conditions specified in ASTM D 1183, Procedure A. After conditioning, the specimens shall be tested in accordance with ASTM D 1002. The average shear value of the specimens shall be reported.4.5.3 Bonding Range: Shall be determined in accordance with ASTM D 816 except that specimens s

31、hall be Type 1 prepared from 1/4 inch (6.4 mm) nominal thickness, commercial grade A fir plywood and 0.062 inch (1.57 mm) nominal thickness AMS 3607 plastic laminate. Report the open drying time which provides maximum strength.4.5.4 Accelerated Aging: Test in accordance with ASTM D 1337, Procedure A

32、. Maintain the adhesive in the original container or in a wide-mouth aluminum or steel container which can be securely sealed. Store the specimens in accordance with ASTM D 618, condition 360/60 + 24/23/50:T-23/50. Determine viscosity in accordance with ASTM D 1084, Method B, using a No. 2 spindle a

33、t a speed of 20 rpm. Report viscosity change in percent from original viscosity.4.5.5 Freeze-Thaw Stability: Maintain the adhesive in the original container or in a wide-mouth aluminum or steel container which can be securely sealed. Cool the specimen to -23 C 3 (-9 F 5), hold at temperature for 12

34、hours 0.5, heat to 50 C 3 (122 F 5), hold at heat for 12 hours 0.5. After three complete cycles, return the specimens to room temperature and determine the viscosity in accordance with ASTM D 1084, Method B, using a No. 2 spindle at a speed of 20 rpm. Report viscosity change in percent from original

35、 viscosity.4.5.6 Nonvolatile Content: Weigh and record the weight of three aluminum foil dishes with suitable covers in place. Pour approximately 10 grams of the thoroughly mixed adhesive into each tared dish. Cover immediately and reweigh. Remove the covers and place the open dishes containing the

36、adhesive in a vented, circulating-air oven for 24 hours 1 at 70 C 3 (158 F 5). Remove the dishes from the oven, replace the covers, allow to cool in a desiccator for not less than one hour, and reweigh. All weighings shall be to the nearest milligram. Calculate the percent nonvolatiles and report as

37、 the average of three determinations.4.5.7 Polyurethane Foam Compatibility: Prepare a specimen approximately 4 x 6 x 1 inch (102 x 152 x 25 mm) from nominal 2 pounds per cubic foot (32 kg/m3) density AMS 3570 polyether-based polyurethane foam. Apply a uniform adhesive coating on one surface of the s

38、pecimen. After drying for not less than one hour, visually inspect the coated surface for indications of attack by the adhesive. Wrinkling, surface sinking, or other evidence of solvent attack is not acceptable.SAE INTERNATIONAL AMS3704A Page 5 of 8_4.6 Reports: The supplier of adhesive shall furnis

39、h with each shipment a report showing the results of tests to determine conformance to tensile shear strength before aging of each lot and stating that the adhesive conforms to the other technical requirements. This report shall include the purchase order number, lot number, AMS 3704A, manufacturers

40、 material designation, date of manufacture, and quantity.4.6.1 A material safety data sheet conforming to AMS 2825, or equivalent, shall be supplied to each purchaser prior to, or concurrent with, the report of preproduction test results or, if preproduction testing be waived by purchaser, concurren

41、t with the first shipment of adhesive for production use. Each request for modification of adhesive formulation shall be accompanied by a revised data sheet for the proposed formulation.4.7 Resampling and Retesting: If any specimen used in the above tests fails to meet the specified requirements, di

42、sposition of the adhesive may be based on the results of testing three additional specimens for each original nonconforming specimen. Failure of any retest specimen to meet the specified requirements shall be cause for rejection of the adhesive represented. Results of all tests shall be reported.5.

43、PREPARATION FOR DELIVERY: 5.1 Packaging and Identification: 5.1.1 A lot of adhesive may be packaged in small quantities and delivered under the basic lot approval provided lot identification is maintained.5.1.2 Adhesive shall be packaged and sealed in round cans. Cans shall have an interior coating

44、which shall not affect or be affected by the adhesive. Containers of one-half gallon (2-L) capacity and above shall be provided with wire handles.5.1.3 Each can of adhesive shall be legibly identified with not less than the following information, applied to durable labels, using characters which wil

45、l not be obliterated by normal handling:ADHESIVE, CONTACT, POLYCHLOROPRENE (CR) RUBBER, RESIN MODIFIEDAMS 3704AMANUFACTURERS IDENTIFICATION _DATE OF MANUFACTURE _LOT NUMBER _QUANTITY _APPROPRIATE WARNINGS OR PRECAUTIONARY NOTICESSAE INTERNATIONAL AMS3704A Page 6 of 8_5.1.4 The individual cans shall

46、be packed in an exterior shipping container capable of protecting the adhesive and maintaining the required temperature during shipment and storage.5.1.5 The exterior of each package shall be legibly marked with not less than the information specified in 5.1.3, with the addition of the purchase order number, so that the markings will not smear or be obliterated during normal handling and use.5.1.6 Contai