SAE AMS 4182H-2016 Aluminum Alloy Wire 5 0Mg - 0 12Mn - 0 12Cr (5056-0) Annealed (UNS A95056).pdf

1、_ 6$(7HFKQLFDO6WDQGDUGV%RDUG5XOHVSURYLGHWKDW7KLVUHSRUW LVSXEOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDODQGHQJL neering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular XVHLQFOXGLQJDQSDWHQWLQIULQJHPHQWDULVLQJWKHUHIURPLVWKHVROH UHVSRQVLELOLWRI

2、WKHXVHU SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in

3、 a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email

4、: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS4182H AEROSPACE MATERIAL SPECIFICATION AMS4182 REV. H Issued 1948-09 Reaffirmed 2006-10 Revised 2016-03 Superseding A

5、MS4182G Aluminum Alloy, Wire 5.0Mg - 0.12Mn - 0.12Cr (5056-O) Annealed (Composition similar to UNS A95056) RATIONALE AMS4182H revises the Title to correct the temper designation, Properties (3.3.1.1) and Reports (4.4.1), and is a Five Year Review and update of this specification. 1. SCOPE 1.1 Form T

6、his specification covers an aluminum alloy in the form of wire (see 8.5). 1.2 Application This wire has been used typically for the manufacture of screen for reinforcement of, and to provide electrical conductivity through, rubber gaskets, but usage is not limited to such applications. 2. APPLICABLE

7、 DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has

8、been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA),

9、www.sae.org. AMS2355 Quality Assurance, Sampling and Testing, Aluminum Alloys and Magnesium Alloy, Wrought Products (Except Forging Stock), and Rolled, Forged, or Flash Welded Rings SAE INTERNATIONAL AMS4182H Page 2 of 5 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive,

10、 P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM B660 Packaging/Packing of Aluminum and Magnesium Products 2.3 ANSI Accredited Publications Copies of these documents are available online at http:/webstore.ansi.org/. ANSI H35.2 Dimensional Tolerances for Aluminu

11、m Mill Products ANSI H35.2M Dimensional Tolerances for Aluminum Mill Products (Metric) 3. TECHNICAL REQUIREMENTS 3.1 Composition Shall conform to the percentages by weight shown in Table 1, determined in accordance with AMS2355. Table 1 - Composition Element min max Silicon Iron Copper Manganese Mag

12、nesium Chromium Zinc Other Elements, each Other Elements, total Aluminum - - - 0.05 4.5 0.05 - - - remainder 0.30 0.40 0.10 0.20 5.6 0.20 0.10 0.05 0.15 3.2 Condition Annealed. 3.3 Properties Wire shall conform to the following requirements; tensile properties shall be determined in accordance with

13、AMS2355 on the mill produced size. 3.3.1 Tensile Properties Shall be shown in Table 2. 3.3.1.1 Mechanical properties for product outside the range covered by Table 2 shall be agreed upon between purchaser and producer. SAE INTERNATIONAL AMS4182H Page 3 of 5 Table 2 - Tensile properties Nominal Diame

14、ter Property Value Up to 0.375 inch (9.52 mm), excl Up to 0.125 inch (3.18 mm), excl 0.125 to 0.375 inch (3.18 to 9.52 mm), excl Tensile Strength, max Elongation in 2 Inches (50.8 mm) or 4D, min Elongation in 2 Inches (50.8 mm) or 4D, min 46.0 ksi (317 MPa) Not required 20% 3.3.2 Bending Wire shall

15、withstand, without cracking, bending at room temperature flat on itself. 3.4 Quality Wire, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the wire. 3.5 Tolerances Shall conform to all applicab

16、le requirements of ANSI H35.2 or ANSI H35.2M. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The vendor of wire shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any

17、confirmatory testing deemed necessary to ensure that the wire conforms to specified requirements. 4.2 Classification of Tests All technical requirements are acceptance tests and shall be performed on each lot. 4.3 Sampling and Testing Shall be in accordance with AMS2355. 4.4 Reports The vendor of wi

18、re shall furnish with each shipment a report stating that the wire conforms to the composition and tolerances, and showing the numerical results of tests on each inspection lot to determine conformance to the other acceptance tests requirements. This report shall include the purchase order number, i

19、nspection lot number, AMS4182H, size, and quantity. The report shall also identify the producer, the product form, and the size of the mill product. 4.4.1 When the product size is outside the range covered by Table 2, the report shall contain a statement to that effect. 4.5 Resampling and Retesting

20、Shall be in accordance with AMS2355. SAE INTERNATIONAL AMS4182H Page 4 of 5 5. PREPARATION FOR DELIVERY 5.1 Packaging and Identification Wire shall be identified as follows: 5.1.1 Wire, supplied on spools, shall contain 5, 10, 15, or 30 pounds (2.27, 4.54, 6.80, or 13.6 kg), as ordered. Each spool s

21、hall be legibly marked, on one flange of the spool or on a durable tag attached to each spool, with not less than the nominal size, alloy number and temper, lot number, AMS4182H, and manufacturers identification. 5.1.2 Straight wire shall be bundled, boxed, or secured on lifts and identified by two

22、durable tags legibly marked with the information of 5.1.1 and attached, not farther than 2 feet (610 mm) from each end, to the wire in each bundle, box, or lift. 5.1.3 Coiled wire shall be identified with the information of 5.1.1, legibly marked on a durable tag attached to each coil or directly on

23、one flange of each spool. 5.1.4 Wire shall be prepared for shipment in accordance with ASTM B660 and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the wire to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT A vendor sh

24、all mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Wire not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 Revision Indicator A change bar (l)

25、 located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical

26、 revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3 When wire is supplied for use in screen, designers may find it necessary to specify that wire in one direction may be in a

27、condition other than annealed. 8.4 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. SAE I

28、NTERNATIONAL AMS4182H Page 5 of 5 8.5 Purchase documents should specify not less than the following: AMS4182H Size of wire desired Length of cut lengths or weight of spools desired Property and acceptance requirements from the cognizant engineering organization applicable to sizes outside the range listed in Table 2 Quantity of wire desired. 8.6 Similar Specifications QQ-A-430, Alloy 5056, Temper O, is listed for information only and shall not be construed as an acceptable alternate unless all requirements of this AMS are met. PREPARED BY AMS COMMITTEE “D“