SAE AMS 4189H-2009 Aluminum Alloy Welding Wire 4 1 Si -0 20 Mg (4643) (UNS A94643)《4 1Si 0 2Mg铝合金焊条》.pdf

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2009 SAE International All rights reserved. No part of this publication ma

3、y be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside US

4、A) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS4189HAEROSPACEMATERIALSPECIFICATIONAMS4189 REV. H Issued 1976-01 Cancelled 2007-08 Revised 2

5、009-11 Superseding AMS4189G Aluminum Alloy Welding Wire 4.1 Si -0.20 Mg (4643) (Composition similar to UNS A94643) RATIONALEAMS4189H restores this document to active status. 1. SCOPE 1.1 FormThis specification covers an aluminum alloy in the form of welding wire. 1.2 ApplicationThis wire has been us

6、ed typically as filler metal for gas-metal-arc or gas-tungsten-arc welding of heavy sections of aluminum alloys of similar composition to produce joints having inherently low dilution ratio of base-metal to weld-metal, and where the weldment may require solution and/or precipitation heat treatment,

7、but usage is not limited to such applications.2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific doc

8、ument issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323

9、 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.AMS2355 Quality Assurance, Sampling and Testing, Aluminum Alloys and Magnesium Alloy, Wrought Products (Except Forging Stock), and Rolled, Forged, or Flash Welded Rings AMS2813 Packaging and Marking of Packages of Welding Wire, Stan

10、dard Method AMS2814 Packaging and Marking of Packages of Welding Wire, Premium Quality AMS2816 Identification, Welding Wire, Tab Marking Method AMS2819 Identification, Welding Wire, Direct Color Code System ARP1876 Weldability Test for Weld Filler Metal Wire ARP4926 Alloy Verification and Chemical C

11、omposition Inspection of Welding Wire Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS4189H Page 2 of 53. TECHNICAL REQUIREMENTS 3.1 Wire Composition Shall conform to the percentages by weight

12、 shown in Table 1, determined in accordance with AMS2355. TABLE 1 - COMPOSITION Element min max Silicon 3.6 4.6 Iron - 0.8 Copper - 0.10 Manganese - 0.05 Magnesium 0.10 0.30 Zinc - 0.10 Titanium - 0.15 Beryllium - 0.0008 (8 ppm) Other Elements,each - 0.05 Other Elements, total - 0.15 Aluminum remain

13、der 3.1.1 Chemical analysis of initial ingot, bar, or rod stock before drawing is acceptable provided the processes used for drawing or rolling, annealing, and cleaning are controlled to ensure continued conformance to chemical composition requirements, and the facility employs procedures to ensure

14、traceability of wire to the originally analyzed source. 3.2 Condition As drawn, in a temper and with a surface finish which will provide proper feeding of the wire in machine welding equipment.3.3 Fabrication3.3.1 Butt welding is permissible provided both ends to be joined are identified by chemical

15、 analysis or the repair is made at the wire processing station. The butt weld shall not interfere with uniform, uninterrupted feeding of the wire in machine welding equipment. 3.3.2 Drawing compounds, oxides, dirt, oil, and other foreign materials shall be removed by cleaning processes which will ne

16、ither result in pitting nor cause gas absorption by the wire or deposition of substances harmful to welding operations.3.4 Weldability Melted wire shall flow smoothly and evenly during welding and shall produce acceptable welds. ARP1876 may be used to resolve disputes. 3.5 QualityWire, as received b

17、y purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to welding operations, operation of welding equipment, or properties of the deposited weld metal.3.6 Sizes and Tolerances Wire shall be supplied in the sizes and to the t

18、olerances shown in 3.6.1 and 3.6.2. 3.6.1 Diameter Shall be shown in Table 2. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS4189H Page 3 of 5TABLE 2A - SIZES AND DIAMETER TOLERANCES, INCH/PO

19、UND UNITS Form Nominal Diameter Inch ToleranceInch Plus ToleranceInch Minus Cut Lengths 0.047, 0.062, 0.079, 0.094, 0.098, 0.125, 0.156, 0.188, 0.197, 0.250 0.003 0.003 Spools 0.030, 0.035, 0.039, 0.047 0.001 0.002 Spools 0.062, 0.079, 0.094, 0.098, 0.125 0.002 0.002 TABLE 2B - SIZES AND DIAMETER TO

20、LERANCES, SI UNITS Form Nominal Diameter Millimeter ToleranceMillimeter Plus ToleranceMillimeter MinusCut Lengths 1.19, 1.57, 2.00, 2.39, 2.50, 3.18, 3.96, 4.78, 5.00, 6.35 0.08 0.08 Spools 0.76, 0.89, 1.00, 1.19 0.025 0.05 Spools 1.57, 2.00, 2.39, 2.50, 3.18 0.05 0.05 3.6.2 LengthCut lengths shall

21、be furnished in 36-inch (914-mm) lengths unless 27-inch (686-mm) or 18-inch (457-mm) lengths are ordered, and shall not vary more than +0, -0.5 inch (+0, -13 mm) from the length ordered. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The vendor of wire shall supply all samples for

22、 vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the wire conforms to specified requirements. 4.2 Classification of Tests 4.2.1 Acceptance Tests Compositio

23、n (3.1) and sizes and tolerances (3.6), and alloy verification (5.2) are acceptance tests and shall be performed on each inspection lot. 4.2.2 Periodic Tests Weldability (3.4) is a periodic test and shall be performed at a frequency selected by the vendor unless frequency of testing is specified by

24、purchaser. 4.3 Sampling and Testing Shall be in accordance with AMS2355. 4.4 Reports The vendor of wire shall furnish with each shipment a report stating that the wire conforms to the composition and other technical requirements. This report shall include the purchase order number, inspection lot nu

25、mber, AMS4189H, nominal size, and quantity. 4.5 Resampling and Retesting Shall be in accordance with AMS2355. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS4189H Page 4 of 55. PREPARATION FO

26、R DELIVERY 5.1 WireWire shall be supplied either on spools in one continuous length for machine welding, or in cut lengths for manual welding, as ordered. Wire on each spool or in each package of cut lengths shall be from the same heat of alloy. 5.1.1 Wire furnished on spools shall be closely wound

27、in layers but adjacent turns within a layer need not be necessarily touching, shall be wound so as to avoid producing kinks, waves, and sharp bends, and shall be free to unwind without restriction caused by overlapping or wedging. 5.2 Alloy Verification Wire on each spool or in each package of cut l

28、engths shall be alloy verified by a method acceptable to purchaser. The alloy verification procedures of ARP4926 are recommended. 5.2.1 An 8-inch (203-mm) length of wire shall be made accessible at one end of each spool for alloy verification. 5.3 IdentificationShall be by tab marking in accordance

29、with AMS2816 unless color coding in accordance with AMS2819 or other method is specified by purchaser. 5.4 Packaging and Marking Shall be by standard method in accordance with AMS2813 unless premium quality method in accordance with AMS2814 or other method is specified by purchaser. 6. ACKNOWLEDGMEN

30、T A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Wire not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 A change bar (|) locat

31、ed in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revis

32、ions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary: dimensions and properties in SI units

33、and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.4 Purchase documents should specify not less than the following: AMS4189HSize and form (spools or cut lengths) of wire desired Length of cut lengths or weight of spool

34、s desired Quantity of wire desired. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS4189H Page 5 of 58.5 Similar Specifications AWS A5.10, ER4643 is listed for information only and shall not be construed as an acceptable alternate unless all requirements of this AMS are met. . PREPARED BY AMS COMMITTEE “D” Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-