SAE AMS 4216B-2003 Aluminum Alloy Sheet 1 0Mg - 0 8Si - 0 8Cu - 0 50Mn (6013-T6) Solution Heat Treated and Artificially Aged (UNS A96013)《固溶热处理的含1 0Mg-0 8Si-0 8Cu-0 50Mn(6013-T6)的人.pdf

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2013 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS4216B AEROSPACE MATERIAL SPECIFICATION AMS4216 REV. B Issued 1989-07 Revised 2

5、003-07 Reaffirmed 2013-12 Superseding AMS4216A Aluminum Alloy, Sheet 1.0Mg - 0.8Si - 0.8Cu - 0.50Mn (6013-T6) Solution Heat Treated and Artificially Aged (Composition similar to A96013) RATIONALE AMS4216B has been reaffirmed to comply with the SAE five-year review policy. 1. SCOPE:1.1 Form: This spe

6、cification covers an aluminum alloy in the form of sheet.1.2 Application: This sheet has been used typically for structural parts requiring good strength, toughness, and fatigue properties and maximum corrosion resistance, but usage is not limited to such applications.2. APPLICABLE DOCUMENTS: The is

7、sue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been canceled and

8、 no superseding document has been specified, the last published issue of that document shall apply.2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or www.sae.org.AMS 2355 Quality Assurance Sampling and Testing, Aluminum Alloys and Magnesium Alloys, Wrought

9、 Products, Except Forging Stock, and Rolled, Forged, or Flash Welded RingsAMS 2772 Heat Treatment of Aluminum Alloy Wrought MaterialsAS1990 Aluminum Alloy TempersSAE INTERNATIONAL AMS4216B Page 2 of 5 2.2 ASTM Publications: Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959

10、 or www.astm.org.ASTM B 660 Packaging/Packing of Aluminum and Magnesium ProductsASTM B 666/B 666M Identification Marking of Aluminum and Magnesium Products2.3 ANSI Publications: Available from ANSI, 25 West 43rd Street, New York, NY 10036 or www.ansi.org.ANSI H35.2 Dimensional Tolerances for Aluminu

11、m Mill ProductsANSI H35.2M Dimensional Tolerances for Aluminum Mill Products (Metric)3. TECHNICAL REQUIREMENTS: 3.1 Composition: Shall conform to the percentages by weight shown in Table 1, determined in accordance with AMS 2355:3.2 Condition: Solution heat treated and artificially aged to the T6 te

12、mper in accordance with AMS 2772 (see AS1990).TABLE 1 - CompositionElement min maxSilicon 0.6 1.0Iron - 0.50Copper 0.6 1.1Manganese 0.20 0.8Magnesium 0.8 1.2Chromium - 0.10Zinc - 0.25Titanium - 0.10Other Elements, each - 0.05Other Elements, total - 0.15Aluminum remainderSAE INTERNATIONAL AMS4216B Pa

13、ge 3 of 5 3.3 Tensile Properties: Sheet shall conform to the requirements shown in Table 2, determined on the mill product size in the long-transverse direction in accordance with AMS 2355:3.4 Quality: Sheet, as received by purchaser, shall be uniform in quality and condition, sound, and free from f

14、oreign materials and from imperfections detrimental to usage of the sheet.3.5 Tolerances: Shall conform to all applicable requirements of ANSI H35.2 or ANSI H35.2M.4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: The vendor of sheet shall supply all samples for vendors tests and s

15、hall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the sheet conforms to specified requirements.4.2 Classification of Tests: All technical requirements of this specification are

16、 acceptance tests and, except for composition, shall be performed on each inspection lot.4.3 Sampling and Testing: Shall be in accordance with AMS 2355.4.4 Reports: The vendor of the product shall furnish with each shipment a report stating that the product conforms to the composition, tolerances an

17、d showing the numerical results of tests on each inspection lot to determine conformance to the other technical requirements. This report shall include the purchase order number, inspection lot number(s), AMS 4216B, size, and quantity. The report shall also identify the producer, the product form, a

18、nd the size of the mill product.TABLE 2 - Minimum Tensile PropertiesProperty ValueTensile Strength 52.0 ksi (359 MPa)Yield Strength at 0.2% Offset 46.0 ksi (317 MPa)Elongation in 2 inches (50.8 mm) 8%SAE INTERNATIONAL AMS4216B Page 4 of 5 4.5 Resampling and Retesting: Shall be in accordance with AMS

19、 2355.5. PREPARATION FOR DELIVERY: 5.1 Identification: Shall be in accordance with ASTM B 666/B 666M.5.2 Packaging: 5.2.1 Product shall be protected from damage during storage and shipment by a method determined by vendor unless specified by purchaser. Examples of typical protective methods include

20、but are not limited to interleaving with paper or oiling of the surface.5.2.2 Sheet shall be prepared for shipment in accordance with ASTM B 660 and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the sheet to ensure carrier acceptance

21、 and safe delivery.6. ACKNOWLEDGMENT: A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders.7. REJECTIONS: Sheet not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection

22、.8. NOTES:8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this specification. An (R) symbol to the left of the document title indicates a complete revision o

23、f the specification, including technical revisions. Change bars and (R) are not used in original publications, nor in specifications that contain editorial changes only.8.2 Terms used in AMS are clarified in ARP1917.8.3 Dimensions and properties in inch/pound units are primary; dimensions and proper

24、ties in SI units are shown as the approximate equivalents of the primary units and are presented only for information.SAE INTERNATIONAL AMS4216B Page 5 of 5 8.4 Purchase documents should specify not less than the following: AMS 4216BSize of sheet desiredQuantity of sheet desiredPREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “D”