SAE AMS 4233C-2003 Aluminum Alloy Welding Wire 4 5Cu - 0 70Ag - 0 30Mn - 0 25Mg - 0 25Ti (201) (UNS A02010)《UNS A02010 4 5Cu-0 70Ag-0 30Mn-0 25Mg-0 25Ti(201)铝合金焊丝》.pdf

1、AEROSPACE MATERIAL SPECIFICATION AMS4233 REV. C Issued 1986-10 Revised 2003-03 Reaffirmed 2014-09 Superseding AMS4233B Aluminum Alloy, Welding Wire4.5Cu - 0.70Ag - 0.30Mn - 0.25Mg - 0.25Ti (201) (Composition similar to UNS A02010) RATIONALE AMS4233C has been reaffirmed to comply with the SAE five ye

2、ar review policy. _ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringe

3、ment arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2014 SAE International All rights reserved.

4、 No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) T

5、el: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS4233C 1. SCOPE:1.1 Form: This specification covers an alumin

6、um alloy in the form of two types of welding wire.1.2 Application: This wire has been used typically as filler metal for gas-metal-arc or gas-tungsten-arc welding of aluminum alloy castings having similar composition and requiring, in the weld zone, response to heat treatment, properties, and corros

7、ion resistance comparable to those of the castings, but usage is not limited to such applications.1.3 Classification: Wire supplied to this specification is classified as follows:Type 1 As Extruded and SizedType 2 As Drawn1.3.1 Unless a specific type is ordered, either type may be supplied.2. APPLIC

8、ABLE DOCUMENTS: The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document

9、 has been cancelled and no superseding document has been specified, the last published issue of that document shall apply.SAE INTERNATIONAL AMS4233C Page 2 of 6 2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or www.sae.org.AMS 2355 Quality Assurance Sampl

10、ing and Testing, Aluminum Alloys and Magnesium Alloys, Wrought Products, Except Forging Stock, and Rolled, Forged, or Flash Welded RingsMAM 2355 Quality Assurance Sampling and Testing, Aluminum Alloys and Magnesium Alloys, Wrought Products, Except Forging Stock, and Rolled, Forged, or Flash Welded R

11、ings, Metric (SI) UnitsAMS 2813 Packaging and Marking of Packages of Welding Wire, Standard MethodAMS 2814 Packaging and Marking of Packages of Welding Wire, Premium QualityAMS 2816 Identification, Welding Wire, Tab Marking MethodAMS 2819 Identification, Welding Wire, Direct Color Code SystemARP1876

12、 Weldability Test for Weld Filler Metal WireARP 4926 Alloy Verification of Chemical Composition inspection of Welding Wire3. TECHNICAL REQUIREMENTS: 3.1 Wire Composition: Shall conform to the percentages by weight shown in Table 1, determined in accordance with AMS 2355 or MAM 2355.3.1.1 Chemical an

13、alysis of initial ingot, bar, or rod stock before drawing is acceptable provided the processes used for drawing or rolling, annealing, and cleaning are controlled to ensure continued conformance to composition requirements, and the facility employs procedures to ensure traceability of wire to the or

14、iginally analyzed source.TABLE 1 - CompositionElement min maxSilicon - 0.05Iron - 0.10Copper 4.0 5.0Manganese 0.20 0.40Magnesium 0.15 0.35Titanium 0.15 0.35Beryllium - 0.0008Silver 0.40 1.0Other Elements, each - 0.03Other Elements, total - 0.10Aluminum remainderSAE INTERNATIONAL AMS4233C Page 3 of 6

15、 3.2 Condition: As drawn or extruded and sized, as ordered. Wire shall be in a temper and with a surface finish which will provide proper feeding of the wire in machine welding equipment.3.3 Fabrication: 3.3.1 Butt welding is permissible provided both ends to be joined are identified by chemical ana

16、lysis or the repair is made at the wire processing station. The butt weld shall not interfere with uniform, uninterrupted feeding of the wire in machine welding equipment.3.3.2 Drawing compounds, oxides, dirt, oil, and other foreign materials shall be removed by cleaning processes which will neither

17、 result in pitting nor cause gas absorption by the wire or deposition of substances harmful to welding operations3.4 Weldability: Melted wire shall flow smoothly and evenly during welding and shall produce acceptable welds. ARP1876 may be used to resolve disputes.3.5 Quality: Wire, as received by pu

18、rchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to welding operations, operation of welding equipment, or properties of the deposited weld metal.3.6 Sizes and Tolerances: Wire shall be supplied in the sizes and to the tole

19、rances shown in 3.6.1 and 3.6.2.3.6.1 Diameter: 3.6.1.1 Extruded Wire: Shall be as shown in Table2.TABLE 2A - Sizes and Diameter Tolerances, Inch/Pound UnitsFormNominal DiameterInchToleranceInchPlus and MinusCut Lengths 0.047, 0.062, 0.079, 0.094, 0.098, 0.125, 0.156, 0.188, 0.197, 0.2500.007Spools

20、0.030, 0.035, 0.039, 0.047,0.062, 0.079, 0.094,0.098, 0.1250.002SAE INTERNATIONAL AMS4233C Page 4 of 6 3.6.1.2 Drawn Wire: Shall be as shown in Table 3.3.6.2 Length: Cut lengths shall be furnished in 36 inch (914 mm) lengths, or as ordered, and shall not vary more than +0, -1 inch (-25 mm) from the

21、length ordered.4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: The vendor of wire shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed n

22、ecessary to ensure that the wire conforms to specified requirements.TABLE 2B - Sizes and Diameter Tolerances, SI UnitsFormNominal DiameterMillimeterToleranceMillimetersPlus and MinusCut Lengths 1.19, 1.57, 2.00, 2.39, 2.50, 3.18, 3.96, 4.78, 5.00, 6.350.18Spools 0.76, 0.89, 1.00, 1.19, 1.57, 2.00, 2

23、.39, 2.50, 3.180.05TABLE 3A - Sizes and Diameter Tolerances, Inch/Pound UnitsFormNominal DiameterInchToleranceInchPlusToleranceInchMinusCut Lengths 0.047, 0.062, 0.079, 0.094, 0.098, 0.125, 0.156, 0.188, 0.197, 0.250 0.003 0.003Spools 0.030, 0.035, 0.039, 0.047 0.001 0.002Spools 0.062, 0.079, 0.094,

24、 0.098, 0.125 0.002 0.002TABLE 3B - Sizes and Diameter Tolerances, SI UnitsFormNominal DiameterMillimeterToleranceMillimeterPlusToleranceMillimeterMinusCut Lengths 1.19, 1.57, 2.00, 2.39, 2.50, 3.18, 3.96, 4.78, 5.00, 6.35 0.08 0.08Spools 0.76, 0.89, 1.00, 1.19 0.025 0.05Spools 1.57, 2.00, 2.39, 2.5

25、0, 3.18 0.05 0.05SAE INTERNATIONAL AMS4233C Page 5 of 6 4.2 Classification of Tests: 4.2.1 Acceptance Tests: Composition (3.1), sizes and tolerances (3.6), and alloy verification (5.2) are acceptance tests and shall be performed on each inspection lot.4.2.2 Periodic Tests: Weldability (3.4) is a per

26、iodic test and shall be performed at a frequency selected by the vendor unless frequency of testing is specified by purchaser.4.3 Sampling and Testing: Shall be in accordance with AMS 2355 or MAM 2355.4.4 Reports: The vendor of wire shall furnish with each shipment a report stating that the wire con

27、forms to the chemical composition and other technical requirements. This report shall include the purchase order number, inspection lot number, AMS 4233C, nominal size, type, and quantity.4.5 Resampling and Retesting: Shall be in accordance with AMS 2355 or MAM 2355.5. PREPARATION FOR DELIVERY: 5.1

28、Wire: Wire shall be supplied either on spools in one continuous length for machine welding, or cut in lengths for manual welding as ordered. Wire on each spool or in each package of cut lengths shall be from the same heat of alloy.5.1.1 Wire furnished on spools shall be closely wound in layers but a

29、djacent turns within a layer need not be necessarily touching, shall be wound so as to avoid producing kinks, waves, and sharp bends, and shall be free to unwind without restriction caused by overlapping or wedging.5.2 Alloy Verification: Wire on each spool or in each package of cut lengths shall be

30、 alloy verified by a method acceptable to purchaser. The alloy verification procedures of ARP4926 are recommended.5.2.1 An 8-inch (203-mm) length of wire shall be made accessible at one end of each spool for alloy analysis, if required.5.3 Identification: Shall be by tab marking in accordance with A

31、MS 2816 unless color coding in accordance with AMS 2819 or other method is specified by purchaser.SAE INTERNATIONAL AMS4233C Page 6 of 6 5.4 Packaging and Marking: Shall be by standard method in accordance with AMS 2813 unless premium quality method in accordance with AMS 2814 or other method is spe

32、cified by purchaser.6. ACKNOWLEDGMENT: A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders.7. REJECTIONS: Wire not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection

33、.8. NOTES: 8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of a specification. An (R) symbol to the left of the document title indicates a complete revision of

34、the specification, including technical revision. Change bars and (R) are not used in original publications, nor in specifications that contain editorial changes only.8.2 Terms used in AMS are clarified in ARP1917.8.3 Dimensions in inch/pound units are primary; dimensions in SI units are shown as the

35、 approximate equivalents of the primary units and are presented only for information.8.4 Purchase documents should specify not less than the following:AMS 4233CType (extruded or drawn) of wire desiredSize and form (spools or cut lengths) of wire desiredLength of cut lengths or weight of spools desiredQuantity of wire desired.PREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “D”