SAE AMS 4245E-2010 Aluminum Alloy Welding Wire 5 0Si - 1 2Cu - 0 50Mg (C355 0) (UNS A03550)《5 0Si 1 2Cu 0 50Mg(C355 0)铝合金焊条》.pdf

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2010 SAE International All rights reserved. No part of this publication ma

3、y be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside US

4、A) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS4245EAEROSPACEMATERIALSPECIFICATIONAMS4245 REV. E Issued 1986-10 Noncurrent 2008-01 Revised

5、2010-04 Superseding AMS4245D Aluminum Alloy, Welding Wire 5.0Si 1.2Cu 0.50Mg (C355.0) (Composition similar to UNS A03550) RATIONALEAMS4245E restores this document to active status. 1. SCOPE 1.1 FormThis specification covers an aluminum alloy in the form of two types of welding wire. 1.2 Application

6、This wire has been used typically as filler metal for gas-metal-arc and gas-tungsten-arc welding of aluminum alloy castings having similar composition and requiring, in the weld zone, response to heat treatment, properties, and corrosion resistance comparable to those of the castings, but usage is n

7、ot limited to such applications. 1.3 Classification Wire supplied to this specification is classified as follows: Type 1 As Extruded and Sized Type 2 As Drawn 1.3.1 Unless a specific type is ordered, either type may be supplied. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect

8、on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specif

9、ied, the last published issue of that document shall apply. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS4245E Page 2 of 62.1 SAE Publications Available from SAE International, 400 Commonwe

10、alth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.AMS2355 Quality Assurance, Sampling and Testing, Aluminum Alloys and Magnesium Alloy Wrought Products (Except Forging Stock), and Rolled, Forged, or Flash Welded Rings AMS2813

11、Packaging and Marking of Packages of Welding Wire, Standard Method AMS2814 Packaging and Marking of Packages of Welding Wire, Premium Quality AMS2816 Identification, Welding Wire, Tab Marking Method AMS2819 Identification, Welding Wire, Direct Color Code System ARP1876 Weldability Test for Weld Fill

12、er Metal Wire ARP4926 Alloy Verification and Chemical Composition Inspection of Welding Wire 3. TECHNICAL REQUIREMENTS 3.1 Wire Composition Shall conform to the percentages by weight shown in Table 1, determined in accordance with AMS2355. TABLE 1 - COMPOSITION Element min max Silicon 4.5 5.5 Iron -

13、 0.20 Copper 1.0 1.5 Manganese - 0.10 Magnesium 0.40 0.6 Zinc - 0.10 Titanium - 0.20 Other Impurities, each - 0.05 Other Impurities, total - 0.15 Aluminum remainder 3.1.1 Chemical analysis of initial ingot, bar, or rod stock before drawing is acceptable provided the processes used for drawing or rol

14、ling, annealing, and cleaning are controlled to ensure continued conformance to composition requirements, and the facility employs procedures to ensure traceability of wire to the originally analyzed source. 3.2 Condition As drawn or extruded and sized, as ordered. Wire shall be in a temper and with

15、 a surface finish which will provide proper feeding of the wire in machine welding equipment. 3.3 Fabrication3.3.1 Butt welding is permissible provided both ends to be joined are identified by chemical analysis or the repair is made at the wire processing station. The butt weld shall not interfere w

16、ith uniform, uninterrupted feeding of the wire in machine welding equipment. 3.3.2 Drawing compounds, oxides, dirt, oil, and other foreign materials shall be removed by cleaning processes which will neither result in pitting nor cause gas absorption by the wire or deposition of substances harmful to

17、 welding operations.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS4245E Page 3 of 63.4 Weldability Melted wire shall flow smoothly and evenly during welding and shall produce acceptable weld

18、s. ARP1876 may be used to resolve disputes. 3.5 Quality Wire, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to welding operations, operation of welding equipment, or properties of the deposited weld meta

19、l.3.6 Sizes and Tolerances Wire shall be supplied in the sizes and to the tolerances shown in 3.6.1 and 3.6.2. 3.6.1 Diameter3.6.1.1 Extruded Wire Shall be as shown in Table 2. TABLE 2A - SIZES AND DIAMETER TOLERANCES, INCH/POUND UNITS FormNominal DiameterInch ToleranceInch Plus and Minus Cut Length

20、s 0.047, 0.062, 0.079, 0.094, 0.098, 0.125, 0.156, 0.188, 0.197, 0.250 0.007 Spools 0.030, 0.035, 0.039, 0.047, 0.062, 0.079, 0.094, 0.098, 0.125 0.002 TABLE 2B - SIZES AND DIAMETER TOLERANCES, SI UNITS FormNominal DiameterMillimetersToleranceMillimeterPlus and Minus Cut Lengths 1.19, 1.57, 2.00, 2.

21、39, 2.50, 3.18, 3.96, 4.78, 5.00, 6.35 0.18 Spools 0.76, 0.89, 1.00, 1.19, 1.57, 2.00, 2.39, 2.50, 3.18 0.05 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS4245E Page 4 of 63.6.1.2 Drawn Wire

22、 Shall be as shown in Table 3. TABLE 3A - SIZES AND DIAMETER TOLERANCES, INCH/POUND UNITS FormNominal DiameterInch ToleranceInch Plus ToleranceInch MinusCut Lengths 0.047, 0.062, 0.079, 0.094, 0.098, 0.125, 0.156, 0.188, 0.197, 0.250 0.003 0.003 Spools 0.030, 0.035, 0.039, 0.047 0.001 0.002 Spools 0

23、.062, 0.079, 0.094, 0.098, 0.125 0.002 0.002 TABLE 3B - SIZES AND DIAMETER TOLERANCES, SI UNITS FormNominal DiameterMillimeterToleranceMillimeterPlus ToleranceMillimeterMinusCut Lengths 1.19, 1.57, 2.00, 2.39, 2.50, 3.18, 3.96, 4.78, 5.00, 6.35 0.08 0.08 Spools 0.76, 0.89, 1.00, 1.19 0.025 0.05 Spoo

24、ls 1.57, 2.00, 2.39, 2.50, 3.18 0.05 0.05 3.6.2 Length Cut lengths shall be furnished in 36 inch (914 mm) lengths, or as ordered, and shall not vary more than +0, -1 inch (-25 mm) from the length ordered. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The vendor of wire shall supp

25、ly all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the wire conforms to specified requirements. 4.2 Classification of Tests 4.2.1 Acceptanc

26、e Tests Composition (3.1), sizes and tolerances (3.6), and alloy verification (5.2) are acceptance tests and shall be performed on each inspection lot. 4.2.2 Periodic Tests Weldability (3.4) is a periodic test and shall be performed at a frequency selected by the vendor unless frequency of testing i

27、s specified by purchaser. 4.3 Sampling and Testing Shall be in accordance with AMS2355. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS4245E Page 5 of 64.4 Reports The vendor of wire shall fu

28、rnish with each shipment a report stating that the wire conforms to the chemical composition and other technical requirements. This report shall include the purchase order number, inspection lot number, AMS4245E, nominal size, type, and quantity. 4.5 Resampling and Retesting Shall be in accordance w

29、ith AMS2355. 5. PREPARATION FOR DELIVERY 5.1 WireWire shall be supplied either on spools in one continuous length for machine welding, or cut in lengths for manual welding as ordered. Wire on each spool or in each package of cut lengths shall be from the same heat of alloy. 5.1.1 Wire furnished on s

30、pools shall be closely wound in layers but adjacent turns within a layer need not be necessarily touching, shall be wound so as to avoid producing kinks, waves, and sharp bends, and shall be free to unwind without restriction caused by overlapping or wedging. 5.2 Alloy Verification Wire on each spoo

31、l or in each package of cut lengths shall be alloy verified by a method acceptable to purchaser. The alloy verification procedures of ARP4926 are recommended. 5.2.1 An 8-inch (203-mm) length of wire shall be made accessible at one end of each spool for alloy analysis, if required.5.3 Identification

32、Shall be by tab marking in accordance with AMS2816 unless color coding in accordance with AMS2819 or other method is specified by purchaser. 5.4 Packaging and Marking Shall be by standard method in accordance with AMS2813 unless premium quality method in accordance with AMS2814 or other method is sp

33、ecified by purchaser. 6. ACKNOWLEDGMENT A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Wire not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejectio

34、n. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS4245E Page 6 of 68. NOTES 8.1 A change bar (l) located in the left margin is for the convenience of the user in locating areas where technica

35、l revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that co

36、ntain editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary: dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary unit

37、s and are presented only for information. 8.4 Purchase documents should specify not less than the following: AMS4245EType (extruded or drawn) of wire desired Size and form (spools or cut lengths) of wire desired Length of cut lengths or weight of spools desired Quantity of wire desired. 8.5 Similar

38、Specifications AWS A5.10, Class R-C355.0 is listed for information only and shall not be construed as an acceptable alternate unless all requirements of this AMS are met. PREPARED BY AMS COMMITTEE “D” Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-