ImageVerifierCode 换一换
格式:PDF , 页数:5 ,大小:39.60KB ,
资源ID:1021474      下载积分:10000 积分
快捷下载
登录下载
邮箱/手机:
温馨提示:
如需开发票,请勿充值!快捷下载时,用户名和密码都是您填写的邮箱或者手机号,方便查询和重复下载(系统自动生成)。
如填写123,账号就是123,密码也是123。
特别说明:
请自助下载,系统不会自动发送文件的哦; 如果您已付费,想二次下载,请登录后访问:我的下载记录
支付方式: 支付宝扫码支付 微信扫码支付   
注意:如需开发票,请勿充值!
验证码:   换一换

加入VIP,免费下载
 

温馨提示:由于个人手机设置不同,如果发现不能下载,请复制以下地址【http://www.mydoc123.com/d-1021474.html】到电脑端继续下载(重复下载不扣费)。

已注册用户请登录:
账号:
密码:
验证码:   换一换
  忘记密码?
三方登录: 微信登录  

下载须知

1: 本站所有资源如无特殊说明,都需要本地电脑安装OFFICE2007和PDF阅读器。
2: 试题试卷类文档,如果标题没有明确说明有答案则都视为没有答案,请知晓。
3: 文件的所有权益归上传用户所有。
4. 未经权益所有人同意不得将文件中的内容挪作商业或盈利用途。
5. 本站仅提供交流平台,并不能对任何下载内容负责。
6. 下载文件中如有侵权或不适当内容,请与我们联系,我们立即纠正。
7. 本站不保证下载资源的准确性、安全性和完整性, 同时也不承担用户因使用这些下载资源对自己和他人造成任何形式的伤害或损失。

版权提示 | 免责声明

本文(SAE AMS 4247B-2006 Aluminum Alloy Hand Forgings 7 7Zn - 2 4Mg - 1 6Cu - 0 16Cr (7049-T7352) Solution Heat Treated Stress Relieved by Compression and Precipitation Heat Treated (UNS.pdf)为本站会员(proposalcash356)主动上传,麦多课文库仅提供信息存储空间,仅对用户上传内容的表现方式做保护处理,对上载内容本身不做任何修改或编辑。 若此文所含内容侵犯了您的版权或隐私,请立即通知麦多课文库(发送邮件至master@mydoc123.com或直接QQ联系客服),我们立即给予删除!

SAE AMS 4247B-2006 Aluminum Alloy Hand Forgings 7 7Zn - 2 4Mg - 1 6Cu - 0 16Cr (7049-T7352) Solution Heat Treated Stress Relieved by Compression and Precipitation Heat Treated (UNS.pdf

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2011 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS4247B AEROSPACE MATERIAL SPECIFICATION AMS 4247 REV. B Issued 1987-01 Revised

5、2006-05 Reaffirmed 2011-11 Superseding AMS 4247A Aluminum Alloy, Hand Forgings 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049-T7352) Solution Heat Treated, Stress Relieved by Compression, and Precipitation Heat Treated (Composition similar to UNS A97049) RATIONALE This document has been reaffirmed to comply w

6、ith the SAE five-year review policy. 1. SCOPE 1.1 Form This specification covers an aluminum alloy in the form of hand forgings procured to inch/pound dimensions. 1.2 Application These forgings have been used typically for parts requiring a combination of high strength and resistance to stress-corro

7、sion cracking and for parts requiring stability during machining, but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier ma

8、y work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 4

9、00 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. AMS 2355 Quality Assurance Sampling and Testing, Aluminum Alloys and Magnesium Alloys, Wrought Products, Except Forging Stock, and Rolled, Forged, or Flash Welded R

10、ings AMS 2772 Heat Treatment of Aluminum Alloy Raw Material AMS 2808 Identification, Forgings AS1990 Aluminum Alloy Tempers SAE AMS 4247B Page 2 of 5 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, ww

11、w.astm.org. ASTM B 594 Ultrasonic Inspection of Aluminum-Alloy Wrought Products for Aerospace Applications ASTM B 660 Packaging/Packing of Aluminum and Magnesium Products ASTM E 1417 Liquid Penetrant Inspection 3. TECHNICAL REQUIREMENTS 3.1 Composition Shall conform to the percentages by weight show

12、n in Table 1, determined in accordance with AMS 2355. TABLE 1 - COMPOSITION Element min max Silicon - 0.25Iron - 0.35Copper 1.2 1.9 Manganese - 0.20Magnesium 2.0 2.9 Chromium 0.10 0.22Zinc 7.2 8.2 Titanium - 0.10Other Elements, each - 0.05Other Elements, total - 0.15Aluminum remainder 3.2 Condition

13、Solution heat treated, stress relieved by compression to produce 1 to 5% permanent set, and precipitation heat treated to the T7352 condition (See AS1990). Heat treatments shall be performed in accordance with AMS 2772. 3.3 Properties Forgings shall conform to the following requirements, determined

14、in accordance with AMS 2355 on the mill product: 3.3.1 Tensile Properties Specimens, machined from forgings having an essentially square or rectangular cross-section heat treated in the indicated thickness, shall have the properties shown in Table 2 provided as-forged thickness does not exceed 5 inc

15、hes (127 mm). SAE AMS 4247B Page 3 of 5 TABLE 2A - MINIMUM TENSILE PROPERTIES, INCH/POUND UNITS Nominal Thickness at Time of Heat Treatment Inches Specimen Orientation Tensile Strength ksi Yield Strength at 0.2% Offset ksi Elongation in 4D % Up to 2, incl Over 2 to 3, incl Over 3 to 4, incl Over 4 t

16、o 5, incl Longitudinal Long-Trans. Longitudinal Long-Trans. Short-Trans. Longitudinal Long-Trans. Short-Trans. Longitudinal Long-Trans. Short-Trans. 71.0 71.0 71.0 71.0 69.0 69.0 69.0 67.0 67.0 67.0 66.0 59.0 57.0 59.0 57.0 56.0 57.0 54.0 53.0 54.0 53.0 51.0 9 4 9 4 3 8 3 2 7 3 2 TABLE 2B - MINIMUM

17、TENSILE PROPERTIES, SI UNITS Nominal Thickness at Time of Heat Treatment Millimeters Specimen Orientation Tensile Strength MPai Yield Strength at 0.2% Offset MPa Elongation in 50.8 mm or 4D % Up to 51, incl Over 51 to 76, incl Over 76 to 102, incl Over 102 to 127, incl Longitudinal Long-Trans. Longi

18、tudinal Long-Trans. Short-Trans. Longitudinal Long-Trans. Short-Trans. Longitudinal Long-Trans. Short-Trans. 490 490 490 490 476 476 476 462 462 462 455 407 393 407 393 386 393 372 365 372 365 352 9 4 9 4 3 8 3 2 7 3 2 3.3.1.1 Tensile specimens cut from special purpose forgings or from forgings beyo

19、nd the size and configuration limits of 3.3.1 shall have tensile properties as specified on the drawing or as agreed upon by purchaser and vendor. 3.3.2 Conductivity Shall be as follows: 3.3.2.1 If the conductivity is 40.0% IACS (International Annealed Copper Standard) or higher and tensile properti

20、es meet specified requirements, forgings are acceptable. 3.3.2.2 If the conductivity is 38.0 to 39.9% IACS, if the tensile properties meet specified requirements, and if the longitudinal yield strength does not exceed the specified minimum value by more than 9.9 ksi (68 MPa), the forgings are accept

21、able. 3.3.2.3 If the conductivity is below 40.0% IACS and the longitudinal yield strength exceeds the specified minimum value by more than 9.9 ksi (68MPa), the forgings shall be given additional precipitation heat treatment. If, after such treatment, the forgings meet the requirements of 3.3.1 and 3

22、.3.2.1 or 3.3.2.2, the forgings are acceptable. 3.3.2.4 If the conductivity is below 38.0% IACS, the forgings are not acceptable and shall be reprocessed regardless of tensile property level. 3.3.3 Stress-Corrosion Resistance Specimens cut from forgings shall show no evidence of stress-corrosion cra

23、cking when stressed to 75% of the specified minimum long-transverse yield strength. SAE AMS 4247B Page 4 of 5 3.4 Quality Forgings, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the forgings.

24、 3.4.1 All forgings shall be subjected to ultrasonic inspection in accordance with ASTM B 594 and shall meet Class A. 3.4.2 When specified, forgings shall be subjected to fluorescent penetrant inspection in accordance with ASTM E 1417. Standards for acceptance shall be established by the cognizant e

25、ngineering organization. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The vendor of forgings shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory test

26、ing deemed necessary to ensure that the forgings conform to specified requirements. 4.2 Classification of Tests 4.2.1 Acceptance Tests Composition (3.1), tensile properties (3.3.1), conductivity (3.3.2), ultrasonic soundness (3.4.1), and, when specified, fluorescent penetrant inspection (3.4.2), are

27、 acceptance tests and, except for composition, shall be performed on each lot. 4.2.2 Periodic Tests Stress-corrosion resistance (3.3.3) is a periodic test and shall be performed at a frequency selected by the vendor unless frequency of testing is specified by purchaser. 4.3 Sampling and Testing Shal

28、l be in accordance with AMS 2355. 4.4 Reports The vendor of forgings shall furnish with each shipment a report stating that the forging conforms to the composition and tolerances and showing the numerical results of tests on each inspection lot to determine conformance to the other acceptance test r

29、equirements. This report shall include the purchase order number, inspection lot number, AMS 4247B, size or part number, and quantity. 4.5 Resampling and Retesting Shall be in accordance with AMS 2355. 5. PREPARATION FOR DELIVERY 5.1 Identification Shall be in accordance with AMS 2808. 5.2 Packaging

30、 Forgings shall be prepared for shipment in accordance with ASTM B 660 and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the forgings to ensure carrier acceptance and safe delivery. SAE AMS 4247B Page 5 of 5 6. ACKNOWLEDGMENT A vendo

31、r shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Forgings not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 A change bar (l) located in

32、 the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this specification. An (R) symbol to the left of the document title indicates a complete revision of the specification, including technical

33、revisions. Change bars and (R) are not used in original publications, nor in specifications that contain editorial changes only. 8.2 Hardness Should be not lower than 135 HB/10/500 or 140 HB/10/1000 but forgings shall not be rejected on the basis of hardness if the tensile property requirements are

34、met. Hardness has been used to verify that product is properly processed, but an “out-of-range hardness number” is not always indicative of product with “out-of-specified tensile strength”. Further analysis, including material composition verification, heat treat process parameter review, and/or ten

35、sile property measurement of product with out-of-range hardness, may be indicated. 8.3 Terms used in AMS are clarified in ARP1917. 8.4 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are sho

36、wn as the approximate equivalents of the primary units and are presented only for information. 8.5 Purchase documents should specify not less than the following: AMS 4247B Size or part number of forgings desired Quantity of forgings desired Acceptance standards for fluorescent penetrant inspection, when specified (see 3.4.2). 8.6 Similar Specifications AMS-A-22771, Alloy 7049, Temper T7352, is listed for information only and shall not be construed as an acceptable alternate unless all requirements of this AMS are met. PREPARED BY AMS COMMITTEE “D“

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1