SAE AMS 4466A-2017 Aluminum Alloy Sheet and Plate Alclad 4 4Cu - 1 5Mg - 0 60Mn (Alclad 2024 -T361 Sheet & Plate) Solution Heat Treated 6% Cold Worked and Naturally Aged (UNS A8202.pdf

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AMS4466A AEROSPACE MATERIAL SPECIFICATION AMS4466 REV. A Issued 2011-12 Revised 2017-09 Superse

5、ding AMS4466 Aluminum Alloy, Sheet and Plate, Alclad 4.4Cu - 1.5Mg - 0.60Mn (Alclad 2024, -T361 Sheet Minimum 0.020 to 0.062 0.508 to 1.575, incl 5 4 0.063 and above 1.600 and above 2.5 2 3.5 Quality The product, as received by purchaser, shall be uniform in quality and condition, sound, and free fr

6、om foreign materials and from imperfections detrimental to usage of the product. 3.6 Ultrasonic Inspection 3.6.1 When specified, each 0.500 inch (12.70 mm) plate shall be ultrasonically inspected in accordance with ASTM B594 and shall meet the requirements for ultrasonic class B. SAE INTERNATIONAL A

7、MS4466A Page 5 of 6 3.7 Tolerances Shall conform to all applicable requirements of ANSI H35.2/H35.2M. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The producer of the product shall supply all samples for producers tests and shall be responsible for the performance of all require

8、d tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements. 4.2 Classification of Tests 4.2.1 Acceptance Tests Composition (3.1), tensile properties (3.3.1), and tolerances (3.7) and, when spe

9、cified, tensile properties for response to temper conversion (3.3.2), and ultrasonic soundness (3.6.1) are acceptance tests and except for composition, shall be performed on each lot. 4.2.2 Periodic Tests Cladding thickness (3.4.1) is a periodic test and shall be performed at a frequency selected by

10、 the producer unless frequency of testing is specified by purchaser. 4.3 Sampling and Testing Shall be in accordance with AMS2355. 4.4 Reports The producer of the product shall furnish with each shipment a report stating that the product conforms to the composition and tolerances, and showing numeri

11、cal results of tests for the other acceptance test requirements. This report shall include the purchase order number, lot number, AMS4466A, size, and quantity. The report shall also identify the producer, the product form, and the size of the mill product. 4.4.1 When the product size is outside the

12、range covered by 1.1, the report shall contain a statement to that effect. 4.4.2 When material produced to this specification, is beyond the sizes allowed in the scope or tables or other exceptions are taken to the technical requirements listed in Section 3 (see 5.1.1), the report shall contain a st

13、atement “This material is certified as AMS4466A(EXC) because of the following exceptions.” and the specific exceptions shall be listed. 4.5 Resampling and Retesting Shall be in accordance with AMS2355. 5. PREPARATION FOR DELIVERY 5.1 Identification Shall be in accordance with ASTM B666/B666M. 5.1.1

14、When technical exceptions are taken (see 4.4.2), the material shall be marked with AMS4466(EXC). SAE INTERNATIONAL AMS4466A Page 6 of 6 5.2 Packaging 5.2.1 Product shall be protected from damage during storage and shipment by a method determined by the producer unless specified by purchaser. Example

15、s of typical protective methods include, but are not limited to interleaving with paper or oiling of the surface. 5.2.2 The product shall be prepared for shipment in accordance with ASTM B660 and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transport

16、ation of the product to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT A producer shall mention this specification number in all quotations and when acknowledging purchase orders. 7. REJECTIONS Product not conforming to this specification, or to modifications authorized by purchaser,

17、 will be subject to rejection. 8. NOTES 8.1 Revision Indicator A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the do

18、cument title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3 Dimensions and properties in inch/pound unit

19、s and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. The tensile properties in Tables 3 and 5 were taken directly from QQ-A-250/5F Amendm

20、ent 2 (AMS-QQ-A-250/5A) and have not been independently verified by AMS statistical procedures. 8.4 Purchase documents should specify not less than the following: AMS4466A Product form and size of product desired Response to temper conversion for T861 (if required) (see 3.3.2) Ultrasonic Inspection (if required) (see 3.6.1) Property and acceptance requirements from the cognizant engineering organization applicable to sizes outside the range listed in 1.1 Quantity of product desired PREPARED BY AMS COMMITTEE “D“