SAE AMS 4558G-2004 Brass Seamless Tubing 66 5Cu - 31 5Zn - 1 6Pb Drawn Temper (H58) (UNS C33200)《66 5Cu、31 5Zn、1 6Pb拉制回火黄铜无缝管(H58)》.pdf

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2012 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS4558G AEROSPACE MATERIAL SPECIFICATION AMS4558 REV. G Issued 1948-05 Revised 2

5、004-04 Reaffirmed 2012-02 Superseding AMS4558F Brass, Seamless Tubing 66.5Cu - 31.5Zn - 1.6Pb Drawn Temper (H58) (Composition similar to UNS C33200) RATIONALE AMS4558G has been reaffirmed to comply with the SAE five-year review policy. 1. SCOPE:1.1 Form: This specification covers a copper alloy (bra

6、ss) in the form of seamless tubing. 1.2 Application: This tubing has been used typically for screw machine parts, but usage is not limited to such applications.2. APPLICABLE DOCUMENTS: The issue of the following documents in effect on the date of the purchase order forms a part of this specification

7、 to the extent supplied herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply.2.1 SAE Pu

8、blications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or www.sae.org.AMS 2223 Tolerances, Copper and Copper Alloy Seamless TubingCopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IH

9、S-,-,-SAE AMS4558G Page 2 of 5 2.2 ASTM Publications: Available from ASTM, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959 or www.astm.org.ASTM B 154 Mercurous Nitrate Test for Copper and Copper AlloysASTM B 251 General Requirements for Wrought Seamless Copper and Copper-Alloy

10、 TubeASTM B 251M General Requirements for Wrought Seamless Copper and Copper-Alloy Tube (Metric)ASTM B 858 Ammonia Vapor Test for Determining Susceptibility to Stress Corrosion Cracking in Copper AlloysASTM E 8 Tension Testing of Metallic MaterialsASTM E 8M Tension Testing of Metallic Materials (Met

11、ric)ASTM E 478 Chemical Analysis of Copper Alloys3. TECHNICAL REQUIREMENTS: 3.1 Composition: Shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E 478, by spectrochemical methods, or by other analytical methods acceptable to purchas

12、er.3.1.1 These composition limits do not preclude the presence of other elements. Limits may be established and analysis required for unnamed elements by agreement between the manufacturer or supplier and purchaser.3.1.2 Zinc may be reported as “remainder”, as the difference between the sum of resul

13、ts for all elements and 100%, or as the result of direct analysis.3.1.3 When all named elements in Table 1 are analyzed, the sum shall be 99.6 percent minimum, but such determination is not required for routine acceptance of each lot.3.2 Condition: Drawn temper, general purpose (H58) (See 8.3).TABLE

14、 1 - CompositionElement (3.1.1) min maxCopper 65.0 68.0Lead 1.50 2.50Iron - 0.07(Zinc (3.1.2) remainder)Sum of Named Elements (3.1.3) 99.6Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS4558G

15、Page 3 of 5 3.3 Fabrication: Tubing shall be produced by a seamless process. The external and internal surface finishes shall be produced by any method which will result in surfaces free from laps, folds, tears, and extraneous materials and which show no oxide discoloration. Processing shall not aff

16、ect limits of wall thickness or corrosion resistance.3.4 Properties: Tubing shall conform to the following requirements:3.4.1 Tensile Strength: Shall be not lower than 54.0 ksi (372 MPa), determined in accordance with ASTM E 8 or ASTM E 8M.3.4.2 Embrittlement: Specimens of tubing, nominally 6 inches

17、 (152 mm) in length or twice the diameter, whichever is greater, shall withstand, without cracking, the mercurous nitrate test performed in accordance with ASTM B 154, Procedure A, or the Ammonia Vapor Test in accordance with ASTM B 858.3.5 Quality: Tubing, as received by purchaser, shall be uniform

18、 in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the tubing.3.6 Tolerances: Shall conform to AMS 2223 as applicable to nonrefractory alloys.4. QUALITY ASSURANCE PROVISIONS: 4.1 Responsibility for Inspection: The vendor of tubing shall s

19、upply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the tubing conforms to specified requirements.4.2 Classification of Tests: 4.2.1 Acce

20、ptance Tests: Composition (3.1), tensile strength (3.4.1), and tolerances (3.6) are acceptance tests and shall be performed on each lot.4.2.2 Periodic Tests: Embrittlement (3.4.2) is a periodic test and shall be performed at a frequency selected by the vendor unless frequency of testing is specified

21、 by purchaser.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS4558G Page 4 of 5 4.3 Sampling and Testing: Shall be in accordance with ASTM B 251 or ASTM B 251M.4.4 Reports: The vendor of tubin

22、g shall furnish with each shipment a report showing the results of tests for chemical composition and tensile properties, and stating that the tubing conforms to the other technical requirements. This report shall include the purchase order number, lot number, AMS 4558G, nominal size and quantity.4.

23、5 Resampling and Retesting: If any specimen used in the above tests fails to meet specified requirements, disposition of the tubing may be based on the results of testing two additional specimens for each original nonconforming specimen. Failure of any retest specimen to meet specified requirements

24、shall be cause for rejection of the tubing represented. Results of all tests shall be reported.5. PREPARATION FOR DELIVERY: 5.1 Identification: Individual tubes or bundles shall have attached a durable tag marked with not less than the purchase order number, lot number, AMS 4558G, and nominal size o

25、r shall be boxed and the box marked with the same information.5.2 Packaging: Tubing shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier

26、 acceptance and safe delivery.6. ACKNOWLEDGMENT: A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders.7. REJECTIONS: Tubing not conforming to this specification, or to modifications authorized by purchaser, will be subject

27、to rejection.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS4558G Page 5 of 5 8. NOTES:8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas whe

28、re technical revisions, not editorial changes, have been made to the previous issue of a specification. An (R) symbol to the left of the document title indicates a complete revision of the specification. Change bars and (R) are not used in original publications, nor in specifications that contain ed

29、itorial changes only.8.2 Hardness should be not lower than as shown in Table 2, determined in accordance with ASTM E 18.Hardness has been used to verify that product is properly processed, but an “out-of-range hardness number” is not always indicative of product with “out-of-specification tensile st

30、rength”. Further analysis including material composition verification, heat treat process parameter review, and/or tensile property measurement on product with out-of-range hardness” may be necessary.8.3 Copper temper designations are defined in ASTM B 601.8.4 Terms used in AMS are clarified in ARP1

31、917.8.5 Dimensions and properties in inch/pound units are primary; dimensions and properties in SI units are shown as the approximate equivalents of the primary units and are presented only for information.8.6 Purchase documents should specify not less than the following: AMS 4558GSize of tubing des

32、iredQuantity of tubing desired.8.7 Similar Specifications: AMS-T-46072, Alloy 332, is listed for information only and shall not be construed as an acceptable alternate unless all requirements of this AMS are met.PREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “D”TABLE 2 - Minimum HardnessNominal Wa

33、llThicknessInchNominal WallThicknessmm Hardness0.012 to 0.020, incl 0.30 to 0.51, incl 78 HR15TOver 0.020 to 0.045, incl Over 0.51 to 1.14, incl 53 HR30TOver 0.045 Over 1.14 55 HRBCopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-