SAE AMS 4803E-2010 Zinc Alloy Castings Die 4 0Al C 0 04Mg (AG40A) As Cast (UNS Z33520)《铸态4 0Al 0 04Mg (AG40A)锌合金铸件 冲模》.pdf

1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report isentirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr

2、om, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2015 SAE InternationalAll rights reserved. No part of this public

3、ation may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (outs

4、ide USA)Fax: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/AMS4803EAEROSPACEMATERIAL SPECIFICATIONAMS4803 REV. EIssued 1944-11Revised 2010-04Reaffirmed 2

5、015-10Superseding AMS4803DZinc Alloy Castings, Die4.0Al 0.04Mg (AG40A)As Cast(Composition similar to UNS Z33520)RATIONALEAMS4803E has been reaffirmed to comply with the SAE five-year review policy.1. SCOPE 1.1 Form This specification covers a zinc alloy in the form of die castings. 1.2 Application T

6、hese castings have been used typically for components requiring moderate strength at room temperature, but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the ext

7、ent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publication

8、s Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.AMS2694 In-Process Welding of Castings AMS2804 Identification, Castings 2.2 ASTM Publications Available from ASTM International,

9、 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM E 536 Chemical Analysis of Zinc and Zinc Alloys ASTM E 1220 Visible Penetrant Examination Using the Solvent-Removable Process ASTM E 1417 Liquid Penetrant Testing 3. TECHNICAL REQUIREMENTS 3

10、1 Composition Shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E 536 or by spectrochemical or other analytical methods acceptable to purchaser. TABLE 1 - COMPOSITION Element min max Aluminum 3.75 4.25 Magnesium 0.03 0.05 Copper

11、 0.10 Iron - 0.10Lead - 0.005 Cadmium - 0.004 Tin - 0.003 Zinc remainder 3.2 ConditionAs cast. 3.3 CastingCastings shall be produced in lots from metal conforming to 3.1. Metal remelted from previously analyzed ingot may be poured directly into castings. Furnace or ladle additions of grain-refining

12、 elements or alloys are permissible. Molten metal taken from alloying furnaces, with or without additions of foundry operating scrap (gates, sprues, risers, and rejected castings), shall not be poured into castings unless first converted to ingot, analyzed, and remelted or unless the composition of

13、a sample taken after the last addition to the melt conforms to 3.1. 3.3.1 A melt shall be the metal withdrawn from a batch-furnace charge of 2000 pounds (907 kg) or less as melted for pouring castings or, when permitted by purchaser, a melt shall be 4000 pounds (1814 kg) or less of metal withdrawn f

14、rom one continuous furnace in not more than eight consecutive hours.3.3.2 A lot shall be all castings poured from a single melt in not more than 8 consecutive hours. 3.4 Chemical Analysis Specimens Shall be cast from each melt and shall be of any suitable size and shape appropriate to the test metho

15、d. 3.5 Quality3.5.1 Castings, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the castings. 3.5.1.1 Castings shall have smooth surfaces and shall be cleaned sufficiently to permit nondestructiv

16、e inspection. SAE INTERNATIONAL AMS4803E Page 2 of 5_3.5.2 When specified, castings shall be produced under radiographic control. This control shall consist of 100% radiographic inspection of castings until process control factors (4.4.2) have been established to ensure production of acceptable cast

17、ings. Unless otherwise specified by purchaser, continued radiographic inspection of production castings shall be performed at a frequency determined by the vendor to ensure continued maintenance of internal quality. 3.5.3 When specified, castings shall be subjected to fluorescent penetrant testing i

18、n accordance with ASTM E 1417, to visible dye penetrant inspection in accordance with ASTM E 1220 or to both. 3.5.4 Radiographic, fluorescent penetrant, visible dye penetrant, and other quality standards shall be as agreed upon by purchaser and vendor. 3.5.5 Castings shall not be repaired by peening

19、 plugging, welding, or other methods without written permission from purchaser.3.5.5.1 When authorized by purchaser, welding in accordance with AMS2694 or other program approved by purchaser may be used. 3.5.6 Castings shall not be impregnated, chemically treated, or coated to prevent leakage unles

20、s specified or allowed by written permission of purchaser, designating the method to be used. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The vendor of castings shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purcha

21、ser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the castings conform to specified requirements. 4.2 Classification of Tests All technical requirements of this specification are acceptance tests and preproduction tests and shall be performed pr

22、ior to or on the first-article shipment of a casting to a purchaser, on each lot, when a change in material, processing, or both requires reapproval as in 4.4.2, and when purchaser deems confirmatory testing to be required. 4.3 Sampling and Testing Shall be in accordance with the following: 4.3.1 On

23、e or more chemical analysis specimen(s) in accordance with 3.4.1 from each melt or a casting from each lot. 4.3.2 One or more preproduction castings in accordance with 4.4.1 of each part number. 4.4 Approval 4.4.1 Sample castings from new or reworked dies and the casting procedure shall be approved

24、by purchaser before castings for production use are supplied, unless such approval be waived by purchaser. 4.4.2 Vendor shall establish for production of sample castings of each part number parameters for the process control factors which will produce acceptable castings; these shall constitute the

25、approved casting procedure and shall be used for producing production castings. If necessary to make any change in parameters for process control factors, vendor shall submit for reapproval a statement of the proposed changes in processing and, when requested, sample castings, test specimens, or bot

26、h. Production castings incorporating the revised operations shall not be shipped prior to receipt of reapproval. SAE INTERNATIONAL AMS4803E Page 3 of 5_4.4.2.1 Control factors for producing castings include, but are not limited to: Type of furnace Alloy additions, fluxing, deoxidation, and gas remov

27、al methods Gating and risering practices Metal pouring temperature; variation of 50 F (28 C) is permissible Solidification and cooling procedures Cleaning procedures Methods of inspection 4.4.2.1.1 Any of the above process control factors for which parameters are considered proprietary by the vendor

28、 may be assigned a code designation. Each variation in such parameters shall be assigned a modified code designation.4.5 ReportsThe vendor of castings shall furnish with each shipment a report showing the results of tests for composition of at least one casting or of separately-cast specimens from e

29、ach melt and stating that the castings conform to the other technical requirements of this specification. This report shall include the purchase order number, lot number, AMS4803E, part number, and quantity. 4.6 Resampling and Retesting If any specimen used in the above tests fails to meet the speci

30、fied requirements, disposition of the castings may be based on the results of testing two additional specimens for each original nonconforming specimen. Failure of any retest specimen to meet the specified requirements shall be cause for rejection of the castings represented. Results of all tests sh

31、all be reported. 5. PREPARATION FOR DELIVERY 5.1 IdentificationShall be in accordance with AMS2804. 5.2 PackagingCastings shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transport

32、ation of the castings to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Castings not conforming to this specification, or to modifications

33、authorized by purchaser, will be subject to rejection. SAE INTERNATIONAL AMS4803E Page 4 of 5_8. NOTES 8.1 A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this d

34、ocument. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3

35、Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.4 Purchase documents should specify no

36、t less than the following: AMS4803EPart number or die number of castings desired Quantity of castings desired Quality acceptance standards (See 3.5.4) 8.5 Similar Specification Federal QQ-Z-363, Composition A, is listed for information only and shall not be construed as an acceptable alternate unless all requirements of this AMS are met. PREPARED BY AMS COMMITTEE “D“ SAE INTERNATIONAL AMS4803E Page 5 of 5_