SAE AMS 4932C-2011 Titanium Alloy Sheet 6Al - 4V Driver Sheet (UNS R56400)《6Al 4V钛合金薄板驾驶员薄板材》.pdf

1、AEROSPACE MATERIAL SPECIFICATION AMS4932 REV. C Issued 1990-04 Revised 2011-02 Reaffirmed 2015-03 Superseding AMS4932B Titanium Alloy Sheet 6Al - 4V Driver Sheet (Composition similar to UNS R56400) RATIONALE AMS4932C has been reaffirmed to comply with the SAE five-year review policy. _ SAE Technical

2、 Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the so

3、le responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2015 SAE International All rights reserved. No part of this publication may

4、be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)

5、 Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS4932C 1. SCOPE 1.1 Form This specification covers a titanium alloy in the form of sheet. 1.2

6、Application This material has been used typically for driver sheet used as a consumable manufacturing aid in superplastic forming of titanium alloy sheet or plate components at 1600 to 1700 F (871 to 927 C), but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS The issue of the foll

7、owing documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no supersedin

8、g document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. AMS2249 Chemical Check

9、 Analysis Limits, Titanium and Titanium Alloys 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM E 8 / E 8M Tension Testing of Metallic Materials ASTM E 539 X-Ray Emission Spectrometr

10、ic Analysis of 6AI-4V Titanium Alloy ASTM E 1409 Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by the Inert Gas Fusion Technique ASTM E 1447 Determination of Hydrogen in Titanium and Titanium Alloys by the Inert Gas Fusion Thermal Conductivity/Infrared Detection Method ASTM E

11、1941 Determination of Carbon in Refractory and Reactive Metals and Their Alloys ASTM E 2371 Analysis of Titanium and Titanium Alloys by Atomic Emission Plasma Spectrometry 3. TECHNICAL REQUIREMENTS 3.1 Composition Shall conform to the percentages by weight shown in Table 1; carbon shall be determine

12、d in accordance with ASTM E 1941, hydrogen in accordance with ASTM E 1447, oxygen and nitrogen in accordance with ASTM E 1409, and other elements in accordance with ASTM E 539 or ASTM E 2371. Other analytical methods may be used if acceptable to the purchaser. TABLE 1 - COMPOSITION Element min max A

13、luminum Vanadium Iron Oxygen Carbon Nitrogen Hydrogen (3.1.2) Other Elements, total (3.1.1) Titanium 5.50 3.50 - - - - - - remainder 6.75 4.50 0.30 0.20 0.08 0.05 (500 ppm) 0.02 (200 ppm) 0.40 3.1.1 Determination not required for routine acceptance. 3.1.2 Sample size when using ASTM E 1447 for hydro

14、gen determination may be as large as 0.35 gram. 3.1.3 Check Analysis Composition variations shall meet the applicable requirements of AMS2249. 3.2 Melting Practice Alloy shall be multiple melted. Melting cycle(s) prior to the final melting cycle shall be made using vacuum consumable electrode, nonco

15、nsumable electrode, electron beam cold hearth, or plasma arc cold heath melting practice(s). The final melting cycle shall be made under vacuum using vacuum arc remelting (VAR) practice with no alloy additions permitted. SAE INTERNATIONAL AMS4932C Page 2 of 6_ 3.2.1 The atmosphere for nonconsumable

16、electrode melting shall be vacuum or shall be inert gas at a pressure not higher than 1000 mm of mercury. 3.2.2 The electrode tip for nonconsumable electrode melting shall be water-cooled copper. 3.3 Condition Hot rolled, flattened, descaled, and, if required, pickled. Sheet may be supplied annealed

17、 or as-rolled, at vendors option. 3.4 Properties Shall conform to the following requirements: 3.4.1 Tensile Properties Shall be as shown in Table 2, determined in accordance with ASTM E 8 / E 8M with the rate of strain set at 0.005 inch/inch/minute (0.005 mm/mm/minute) and maintained within a tolera

18、nce of 0.002 inch/inch/minute (0.002 mm/mm/minute) through the 0.2% offset yield strain. TABLE 2 - MINIMUM TENSILE PROPERTIES Property Value Tensile Strength 134 ksi (924 MPa) Yield Strength at 0.2% Offset 126 ksi (869 MPa) Elongation in 2 Inches (50.8 mm) 5% 3.4.1.1 Tensile properties shall be dete

19、rmined in the transverse direction. 3.4.1.2 Sheet shall not be rejected on the basis of tensile properties if all other technical requirements are met. 3.4.2 Microstructure Shall be the structure resulting from processing within the alpha-beta phase field. Microstructure shall conform to 3.4.2.1 or

20、3.4.2.2. 3.4.2.1 Equiaxed and/or elongated primary alpha in a transformed beta matrix with no continuous network of alpha at prior beta grain boundaries. 3.4.2.2 Essentially complete field of equiaxed and/or elongated alpha with or without intergranular beta and no continuous network of alpha at pri

21、or grain boundaries. 3.4.3 Surface Contamination Sheet shall be free of any oxygen-rich layer (See 8.2), such as alpha case, or other surface contamination, determined by microscopic examination at 400X or other method acceptable to purchaser. 3.5 Quality Sheet, as received by purchaser, shall be un

22、iform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the product. SAE INTERNATIONAL AMS4932C Page 3 of 6_ 3.6 Tolerances Shall conform to the following: 3.6.1 Length and Width -0, +1/4 inch (-0, +6.4 mm). 3.6.2 Thickness -0, +0.013 inc

23、h (-0, +0.33 mm). 3.6.3 Flatness Shall not deviate more than 3% for sheet 36 inches (914 mm) and under in width, and not more than 5% for sheet over 36 inches (914 mm) in width. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The vendor of sheet shall supply all samples for vendors

24、 tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the sheet conforms to specified requirements. 4.2 Classification of Tests 4.2.1 Acceptance Tests Composition (3.1)

25、 surface contamination (3.4.3), and tolerances (3.6) are acceptance tests and shall be performed on each heat or lot as applicable. 4.2.2 Periodic Tests Tensile properties (3.4.1) and microstructure (3.4.2) are periodic tests and shall be performed at a frequency selected by the vendor unless frequ

26、ency of testing is specified by purchaser. 4.3 Sampling and Testing Shall be in accordance with the following; a lot shall be all sheet from the same heat processed at the same time; a heat shall be the vacuum arc remelted ingots produced from alloy originally melted as a single furnace charge. 4.3.

27、1 For Acceptance Tests 4.3.1.1 Composition One sample from each heat, except that for hydrogen one sample from each lot obtained after thermal and chemical processing is completed. 4.3.1.2 Surface Contamination and Tolerances One sample from each lot. SAE INTERNATIONAL AMS4932C Page 4 of 6_ 4.3.2 Fo

28、r Periodic Tests One sample. 4.4 Reports The vendor shall provide a copy of the original material manufacturers report (material certification), including: producer name, product form, mill produced size, and country where the metal was melted (i.e., final melt in the case of metal processed by mult

29、iple melting operations). The vendor of sheet shall furnish with each shipment a report showing the results of tests for composition of each heat and for hydrogen content, tensile properties when determined, and surface contamination of each lot, and stating that the sheet conforms to the other tech

30、nical requirements. This report shall include the purchase order number, heat and lot numbers, AMS4932C, size, and quantity. 4.5 Resampling and Retesting If any specimen used in the above tests fails to meet the specified requirements, disposition of the sheet may be based on the results of testing

31、three additional specimens for each original nonconforming specimen. Failure of any retest specimen to meet the specified requirements shall be cause for rejection of the sheet represented. Results of all tests shall be reported. 5. PREPARATION FOR DELIVERY 5.1 Identification Each sheet shall be mar

32、ked on one face in lengthwise rows of characters recurring at intervals not greater than 3 feet (914 mm), the rows being spaced not more than 6 inches (152 mm) apart and alternately staggered, with DRIVER SHEET, AMS4932C, heat number, lot number, manufacturers identification, and nominal thickness.

33、The characters shall be of such size as to be legible, shall be applied using a suitable marking fluid whose residue shall contain no more than traces of halogen-bearing compounds, and shall be removable in hot alkaline cleaning solution without rubbing. The markings shall have no deleterious effect

34、 on the sheet or its performance and shall be sufficiently stable to withstand normal handling. 5.2 Packaging Sheet shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation

35、of the sheet to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT A vendor shall include this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Sheet not conforming to this specification, or to modifications authorized b

36、y purchaser, will be subject to rejection. SAE INTERNATIONAL AMS4932C Page 5 of 6_ 8. NOTES 8.1 A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An

37、 (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 An oxygen rich layer, such as alpha case, is hard and britt

38、le and results in marked lowering of ductility of the product. 8.3 Terms used in AMS are clarified in ARP1917. 8.3.1 Terminology relating to titanium microstructures is presented in AS1814. 8.4 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and

39、properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.5 Purchase documents should specify not less than the following: AMS4932C Size of sheet desired Quantity of sheet desired Microstructure and tensile testing, if required (See 4.2.2). PREPARED BY AMS COMMITTEE “G“ SAE INTERNATIONAL AMS4932C Page 6 of 6_