SAE AMS 5085J-2017 Steel Sheet Strip and Plate 0 48 - 0 55C (SAE 1050) (UNS G10500).pdf

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2017 SAE InternationalAll rights reserved. No part of this publi

3、cation may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (out

4、side USA)Fax: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on thisTechnical Report, please visithttp:/standards.sae.org/AMS5085JAEROSPACEMATERIAL SPECIFICATIONAMS5085 REV. JIssued 1954-05Revised 2017-03Superseding AMS5085HSteel

5、 Sheet, Strip, and Plate0.48 - 0.55C (SAE 1050)(Composition similar to UNS G10500)RATIONALEAMS5085J results from a Five-Year Review and update of this specification that revises grain size testing requirements (3.1.1 and 3.3.3), allows additional heat treatments (3.2), prohibits cutting bar from pla

6、te (3.2.2), and revises decarburization testing (3.3.2) and reporting (4.4).1. SCOPE1.1 FormThis specification covers a carbon steel in the form of sheet, strip, and plate.1.2 ApplicationThese products have been used typically for stamped or formed parts that may subsequently be heat treated, but us

7、age is not limited to such applications.2. APPLICABLE DOCUMENTSThe issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document i

8、ssue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply.2.1 SAE PublicationsAvailable from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside

9、USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org.AMS2232 Tolerances Carbon Steel, Sheet, Strip, and PlateAMS2259 Chemical Check Analysis Limits Wrought Low-Alloy and Carbon SteelsAMS2370 Quality Assurance Sampling and Testing Carbon and Low-Alloy Steel Wrought Products and Forging Stock

10、SAE INTERNATIONAL AMS5085J Page 2 of 5AMS2807 Identification Carbon and Low-Alloy Steels, Corrosion and Heat-Resistant Steels and Alloys Sheet, Strip, Plate, and Aircraft TubingARP1917 Clarification of Terms Used in Aerospace Metals Specifications2.2 ASTM PublicationsAvailable from ASTM Internationa

11、l, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM A370 Mechanical Testing of Steel ProductsASTM E112 Determining Average Grain SizeASTM E140 Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Supe

12、rficial Hardness, Knoop Hardness, Scleroscope Hardness, and Leeb Hardness Rockwell HardnessASTM E350 Chemical Analysis of Carbon Steel, Low-Alloy Steel, Silicon Electrical Steel, Ingot Iron, and Wrought IronASTM E384 Microindentation Hardness of Materials3. TECHNICAL REQUIREMENTS3.1 CompositionShall

13、 conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E350, by spectrochemical methods, or by other analytical methods acceptable to purchaser.Table 1 - CompositionElement Min MaxCarbon 0.48 0.55Manganese 0.60 0.90Silicon 0.15 0.30Phosphor

14、us - 0.030Sulfur - 0.0353.1.1 Aluminum is an optional grain refining element and need not be determined or reported unless used to satisfy the average grain size requirements of 3.3.3.3.1.2 Check AnalysisComposition variations shall meet the applicable requirements of AMS2259.3.2 ConditionThe produc

15、t shall be supplied in the following condition; hardness shall be not higher than 85 HRB, or equivalent (see 8.2), determined in accordance with ASTM A370:3.2.1 Sheet and StripCold rolled and bright annealed; or hot rolled, annealed, sub-critically annealed or normalized, if necessary, and descaled.

16、3.2.2 PlateHot rolled, annealed, sub-critically annealed or normalized if necessary, and descaled. Bar shall not be cut from plate (also see 4.4.1).SAE INTERNATIONAL AMS5085J Page 3 of 53.2.2.1 If allowed by the purchaser, cold rolled, annealed, sub-critically annealed or normalized if necessary, an

17、d descaled as necessary, having hardness not higher than 85 HRB, or equivalent (see 8.2).3.3 PropertiesThe product shall conform to the following requirements; hardness and bend tests shall be performed in accordance with ASTM A370:3.3.1 BendingThe product shall withstand, without cracking, bending

18、at room temperature through an angle of 180 around a diameter equal to twice the nominal thickness of the product with axis of bend parallel to the direction of rolling.3.3.2 DecarburizationDecarburization shall be evaluated by one of the methods of 3.3.2.1 or 3.3.2.2.3.3.2.1 Metallographic MethodA

19、cross section taken perpendicular to the surface shall be prepared, etched, and visually examined metallographically at a magnification not to exceed 100X. The product shall not show a layer of complete (ferrite) or partial decarburization exceeding the limits of Table 2.3.3.2.2 Hardness Traverse Me

20、thodThe total depth of decarburization shall be determined by a traverse method using microindentation hardness testing in accordance with ASTM E384, at a magnification not exceeding 100X, conducted on a hardened but untempered specimen protected during heat treatment to prevent changes in surface c

21、arbon content. Tempering is generally not recommended, but if tempered, the tempering temperature shall be not higher than 300 F (149 C). Depth of decarburization is defined as the perpendicular distance from the surface to the depth under that surface where there is not further increase in hardness

22、. Such measurements shall be far enough away from any adjacent surface to be uninfluenced by any decarburization on the adjacent surface. Acceptance shall be as listed in Table 2. Table 2Table 2A - Maximum depth of decarburization, inch/pound unitsNominal ThicknessInchesTotal Depth ofDecarburization

23、Inch0.375 to 0.500, incl 0.015Over 0.500 to 1.000, incl 0.025Over 1.000 to 2.000, incl 0.035Table 2B - Maximum depth of decarburization, SI unitsNominal ThicknessMillimetersTotal Depth ofDecarburizationMillimeter9.52 to 12.70, incl 0.38Over 12.70 to 25.40, incl 0.64Over 25.40 to 50.80, incl 0.893.3.

24、2.3 When determining the depth of decarburization, it is permissible to disregard local areas provided the decarburization of such areas does not exceed the above limits by more than 0.005 inch (0.13 mm) and the width is 0.065 inch (1.65 mm) or less.3.3.2.4 In the case of dispute, the total depth of

25、 decarburization determined using the microindentation hardness traverse method shall govern.SAE INTERNATIONAL AMS5085J Page 4 of 53.3.3 Average Grain SizeAverage grain size shall be determined by either 3.3.3.1 or 3.3.3.2.3.3.3.1 Shall be ASTM No. 5 or finer, determined in accordance with ASTM E112

26、.3.3.3.2 The product of a heat shall be considered to have an ASTM No. 5 or finer austenitic grain size if one or more of the following are determined by heat analysis (see 8.6):3.3.3.2.1 A total aluminum content of 0.020 to 0.050%.3.3.3.2.2 An acid soluble aluminum content of 0.015 to 0.050%.3.4 Qu

27、alityThe product, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the product.3.5 TolerancesShall conform to all applicable requirements of AMS2232.4. QUALITY ASSURANCE PROVISIONS4.1 Responsibi

28、lity for InspectionThe producer of the product shall supply all samples for producers tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to speci

29、fied requirements.4.2 Classification of TestsAll technical requirements are classified as acceptance tests and shall be performed on each heat or lot as applicable. If grain refining elements (3.3.3.2) are not present, the ASTM E112 grain size test (3.3.3.1) shall be conducted on each lot.4.2.1 If a

30、luminum as a grain refining element (3.3.2.2) is present, the ASTM E112 grain size test (3.3.2.1) shall beconducted on a periodic basis and shall be performed at a frequency selected by the producer (not to exceed 1 year) unless frequency of testing is specified by purchaser.4.3 Sampling and Testing

31、Shall be in accordance with the AMS2370.4.4 Reports4.4.1 The producer of the product shall furnish with each shipment a report showing the producer identity, results of tests for composition of each heat and for hardness, bending, and (if measured) average grain size of each lot, and stating that th

32、e product conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers, AMS5085J, size, product form, and quantity. If the grain size requirement of 3.3.3.2 is met by the aluminum, the aluminum content shall be reported and a statement that

33、the chemistry satisfies the grain size requirement shall be included.4.4.2 Report the nominal metallurgically worked cross sectional size and the cut size, if different (also see 3.2.1).4.5 Resampling and RetestingShall be in accordance with AMS2370.SAE INTERNATIONAL AMS5085J Page 5 of 55. PREPARATI

34、ON FOR DELIVERY5.1 IdentificationShall be in accordance with AMS2807.5.2 Protective TreatmentProduct shall be protected from corrosion prior to shipment.5.3 PackagingThe product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulati

35、ons pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe delivery.6. ACKNOWLEDGMENTA producer shall include this specification number and its revision letter in all quotations and when acknowledging purchase orders.7. REJECTIONSProduct not co

36、nforming to this specification, or to modifications authorized by purchaser, will be subject to rejection.8. NOTES8.1 Revision IndicatorA change bar (I) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to

37、 the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only.8.2 Hardness conversion

38、tables for metals are presented in ASTM E140.8.3 Terms used in AMS are clarified in ARP1917.8.4 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of th

39、e primary units and are presented only for information.8.5 Purchase documents should specify not less than the following:AMS5085JProduct form and size of product desiredQuantity of product desired8.6 Grain SizeThe average grain size resulting from using the appropriate test procedures per ASTM E112

40、will satisfy an ASTM No. 5 or finer grain size when the element defined in 3.3.3.2 as grain refiner is present. Other technical societies have adopted the verification of fine grain steel based on chemistry alone. Included are ASTM International (Documents A6, A20, and A29); American Society of Mechanical Engineers (Documents SA6, SA20, and SA29); American Bureau of Shipping; CSA Group (Canada); EuroNorm documents; American Association of State Highway and Transportation Officials. PREPARED BY AMS COMMITTEE “E”