SAE AMS 5401C-2004 Nickel Alloy Corrosion and Heat-Resistant Investment Castings 62Ni - 21 5Cr - 9 0Mo - 3 6Cb (Nb) Vacuum Melted Vacuum Cast As Cast (UNS N26625)《UNS N26625经真空融化和真.pdf

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2011 SAE International All rights reserved. No part of this publication m

3、ay be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside U

4、SA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5401C AEROSPACE MATERIAL SPECIFICATION AMS 5401 REV. C Issued 1980-01 Revised 2004-05 Reaf

5、firmed 2011-10 Superseding AMS 5401B Nickel Alloy, Corrosion and Heat-Resistant, Investment Castings 62Ni - 21.5Cr - 9.0Mo - 3.6Cb (Nb) Vacuum Melted, Vacuum Cast As Cast (Composition similar to UNS N26625) 1. SCOPE: 1.1 Form: This specification covers a corrosion and heat-resistant, vacuum melted,

6、nickel alloy in the form of investment castings. 1.2 Application: These castings have been used typically for structural parts requiring high strength up to 1600 F (871 C) and oxidation and corrosion resistance up to 1800 F (982 C), but usage is not limited to such applications. 1.3 Classification:

7、Castings conforming to this specification are classified as follows: Class 1 - Trace element limits conforming to AMS 2280, Class 1 (AMS 2280-1) Class 2 - Trace element limits conforming to AMS 2280, Class 2 (AMS 2280-2) Class 3 - Trace element limits do not apply 1.3.1 Castings shall conform to Cla

8、ss 1 unless Class 2 or Class 3 is specified by purchaser. 2. APPLICABLE DOCUMENTS: The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a

9、 specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. SAE AMS 5401C Page 2 of 11 2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15

10、096-0001 or www.sae.org. AMS 2175 Castings, Classification and Inspection of AMS 2269 Chemical Check Analysis Limits, Nickel, Nickel Alloys, and Cobalt Alloys AMS 2280 Trace Element Control, Nickel Alloy Castings AMS 2360 Room Temperature Tensile Properties of Castings AMS 2694 Repair Welding of Aer

11、ospace Castings AMS 2804 Identification, Castings 2.2 ASTM Publications: Available from ASTM, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959 or www.astm.org. ASTM E 8 Tension Testing of Metallic Materials ASTM E 8M Tension Testing of Metallic Materials (Metric) ASTM E 354 Che

12、mical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys ASTM E 1417 Liquid Penetrant Examination ASTM E 1742 Radiographic Examination 3. TECHNICAL REQUIREMENTS: 3.1 Composition: Shall conform to the percentages by weight shown in Table 1, determine

13、d by wet chemical methods in accordance with ASTM E 354, by spectrochemical methods, or by other analytical methods acceptable to purchaser (See 8.2.1 and 8.2.2). SAE AMS 5401C Page 3 of 11 TABLE 1 - Composition Element min max Carbon - 0.10 Manganese - 0.50 Silicon - 0.50 Phosphorus - 0.015 Sulfur

14、- 0.015 Chromium 20.00 23.00 Molybdenum 8.00 10.00 Columbium (Niobium) (3.1.1) 3.15 4.15 Cobalt - 1.00 Titanium (3.1.2) - 0.40 Tantalum (3.1.1, 3.1.3) - 0.15 Aluminum (3.1.2) - 0.40 Iron - 5.00 Copper - 0.30 Other Elements (3.1.3) - - Nickel remainder 3.1.1 Sum of columbium (niobium) plus tantalum s

15、hall not exceed 4.15% by weight. 3.1.2 Shall be present but not in excess of maximum content specified. 3.1.3 Determination not required for routine acceptance. 3.1.4 Vendor may test for any element not otherwise listed in Table 1 and include this analysis in the report of 4.5. Limits of acceptabili

16、ty may be specified by purchaser (See 8.2.3). 3.1.5 Trace Elements: Shall conform to AMS 2280-1 unless AMS 2280-2 or AMS 5401 Class 3 is specified by purchaser (See 1.3). 3.1.6 Check Analysis: Composition variations shall meet the applicable requirements of AMS 2269. 3.2 Melting Practice: Castings a

17、nd specimens shall be poured at casting vendors facility either from a melt (See 8.2.4) of a master heat, or directly from a master heat (See 3.4.2 and 8.2.5). 3.2.1 Revert (gates, sprues, risers, and rejected castings) may be used only in the preparation of master heats; revert shall not be remelte

18、d directly without refining for pouring of castings. Melting of revert creates a new master heat. 3.2.1.1 The metal for castings and specimens shall be melted and poured under vacuum without loss of vacuum between melting and pouring. When authorized by purchaser, protective atmosphere may be used i

19、n lieu of vacuum for pouring of castings. SAE AMS 5401C Page 4 of 11 3.2.2 Portions of two or more qualified master heats (See 3.4.2) may be melted together and poured into castings using a procedure authorized by purchaser. 3.2.3 If melts (See 8.2.4) are modified by replenishment (See 8.2.7), vendo

20、r shall have a written procedure acceptable to purchaser which defines the controls, test, and traceability criteria for both castings and separately-cast specimens. Control factors of 4.4.2.2 shall apply. 3.3 Condition: Castings shall be delivered in the as-cast condition. 3.4 Test Specimens: Speci

21、mens shall be either separately-cast, integrally-cast (See 8.2. 8), or machined from a casting, and shall conform to 3.2. 3.4.1 If specimens are separately-cast, vendor shall have a written procedure acceptable to purchaser. Control factors of 4.4.2.2 shall apply. 3.4.2 Each master heat shall be qua

22、lified by evaluation of chemical and tensile specimens. 3.4.2.1 If replenishments are made at remelt as in 3.2.3, the frequency of sampling and testing used by the vendor for qualification to 3.4.2 shall be acceptable to purchaser. 3.4.2.2 The tensile tests of 3.4.2 are not required if these tests a

23、re conducted using integrally-cast specimens (4.3.3.2) or machined-from-casting (4.3.3.3). 3.4.3 Chemical Analysis Specimens: Shall be of any convenient size and shape. 3.4.4 Tensile Specimens: Shall be of standard proportions in accordance with ASTM E 8 or ASTM E 8M (See 8.4) with 0.250-inch (6.35-

24、mm) diameter at the reduced parallel gage section. 3.4.4.1 Separately-cast and integrally-cast specimens may be either cast to size, and/or cast oversize and subsequently machined to 0.250-inch (6.35-mm) diameter. 3.4.4.2 When integrally-cast specimens and specimens machined-from-casting are specifi

25、ed, specimen size and location shall be agreed upon by purchaser and vendor (See 8.2.9 and 8.3). 3.5 Heat Treatment: Not applicable. SAE AMS 5401C Page 5 of 11 3.6 Properties: Conformance shall be based upon testing of separately-cast specimens unless purchaser specifies integrally-cast specimens or

26、 specimens machined-from-casting. Properties for integrally-cast specimens and specimens machined-from-casting shall be as specified by purchaser (See 8.3). 3.6.1 Room Temperature Tensile Properties: Shall be as specified in 3.6.1.1, determined in accordance with ASTM E 8 or ASTM E 8M (See 8.4). Pro

27、perties other than those listed in Table 2 may be defined as specified in AMS 2360. 3.6.1.1 Separately-Cast Specimens: Shall be as shown in Table 2. TABLE 2 - Minimum Tensile Properties of Separately-Cast Specimens Property Value Tensile Strength 85 ksi (586 MPa) Yield Strength at 0.2% Offset 45.0 k

28、si (310 MPa) Elongation in 4D 25% 3.7 Quality: 3.7.1 Castings, as received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the castings. Castings shall be free of cracks, laps, hot tears, cold shuts, and f

29、ree of scale and other process-induced surface contamination which would obscure defects. 3.7.2 Castings shall be produced under radiographic control. This control shall consist of radiographic examination of each casting part number until foundry manufacturing controls in accordance with 4.4.2 have

30、 been established. Additional radiography shall be conducted in accordance with the frequency of inspection specified by purchaser, or as necessary to ensure continued maintenance of internal quality. 3.7.2.1 Radiographic inspection shall be conducted in accordance with ASTM E 1742 or other method s

31、pecified by purchaser. 3.7.3 When specified, castings shall be subjected to fluorescent penetrant inspection in accordance with ASTM E 1417 or other method specified by purchaser. 3.7.4 Acceptance standards for radiographic, fluorescent penetrant, visual, and other inspection methods shall be as agr

32、eed upon by purchaser and vendor (See 8.2.9). AMS 2175 may be used to specify acceptance standards (casting grade) and frequency of inspection (casting class). 3.7.4.1 When acceptance standards are not specified, Grade C of AMS 2175 as applicable to steel castings shall apply for each applicable met

33、hod of inspection. SAE AMS 5401C Page 6 of 11 3.7.5 Castings shall not be peened, plugged, impregnated, or welded unless authorized by purchaser. 3.7.5.1 When authorized by purchaser, welding in accordance with AMS 2694 or other welding program acceptable to purchaser may be used. 4. QUALITY ASSURAN

34、CE PROVISIONS: 4.1 Responsibility for inspection: The vendor of castings shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the c

35、astings conform to specified requirements. 4.2 Classification of Tests: 4.2.1 Acceptance Tests: Composition (3.1), room temperature tensile properties (3.6.1), and the applicable requirements of quality (3.7) are acceptance tests and shall be performed as specified in 4.3. 4.2.2 Periodic Tests: Radi

36、ographic soundness (3.7.2) is a periodic test and shall be performed at a frequency selected by the vendor unless frequency of testing is specified by purchaser. 4.2.3 Preproduction Tests: All technical requirements are preproduction tests and shall be performed on sample castings (4.3.2), when a ch

37、ange in control factors occurs (4.4.2.2), and when purchaser deems confirmatory testing to be required. 4.3 Sampling and Testing: The minimum testing performed by vendor shall be in accordance with the following: 4.3.1 One chemical analysis specimen or a casting from each master heat shall be tested

38、 for conformance with Table 1; if 3.4.2.1 applies, test frequency shall be acceptable to purchaser. 4.3.2 One preproduction casting in accordance with 4.4 shall be tested to requirements of the casting drawing and to all technical requirements. 4.3.2.1 Dimensional inspection sample quantity shall be

39、 as specified by purchaser. 4.3.3 Tensile property tests shall be conducted to determine conformance with 3.6.1. Sampling and test frequency is dependent upon the type and origin of the specimen specified by purchaser (See 3.4.4 and 3.6) or selected by vendor (See 4.3.3.4). When 3.4.2.1 applies, spe

40、cimen source and test frequency shall be acceptable to purchaser. 4.3.3.1 For separately-cast specimens in the as-cast condition, one specimen from each master heat shall be tested for conformance to 3.6.1. SAE AMS 5401C Page 7 of 11 4.3.3.2 For integrally-cast specimens in the as-cast condition, tw

41、o specimens shall be randomly selected from each lot (See 8.2.10) and tested for conformance to properties specified by purchaser (See 3.6 and 8.3). 4.3.3.3 For specimens machined from a casting, one casting shall be randomly selected from each lot and tested in the as-cast condition locations shown

42、 on the engineering drawing for conformance to properties specified by purchaser (See 3.6 and 8.3). 4.3.3.3.1 When size and location of specimens are not shown, two specimens shall be tested, one from the thickest section and one from the thinnest section. Once established under 4.4.2.2, test locati

43、ons may be changed only as agreed upon by purchaser and vendor. 4.3.3.4 When acceptable to purchaser, specimens machined-from-casting may be used in lieu of both separately-cast and integrally-cast specimens, and integrally-cast specimens may be used in lieu of separately-cast specimens. In each cas

44、e, the resultant properties shall conform to the alternate requirements specified by purchaser (See 8.3). If alternate requirements are not specified, the resultant properties shall conform to the requirements of 3.6 for separately-cast specimens. 4.3.3.4.1 When specimens are selected for test as in

45、 4.3.3.4 from an origin other than that specified by purchaser, vendor shall include in the report of 4.5 a description of the source of the specimen that was tested. 4.3.3.5 When casting size, section thickness, gating method, or other factors do not permit conformance with 4.3.3.2 or 4.3.3.3, samp

46、ling and testing shall be agreed upon by purchaser and vendor. 4.3.4 Castings shall be inspected in accordance with 3.7 to the methods, frequency, and acceptance standards specified by purchaser. 4.4 Approval: 4.4.1 Sample casting(s) from new or reworked master patterns produced under the casting pr

47、ocedure of 4.4.2 shall be approved by purchaser before castings for production use are supplied, unless such approval be waived by purchaser. 4.4.2 For each casting part number, vendor shall establish parameters for process control factors that will consistently produce castings and test specimens m

48、eeting the requirements of the casting drawing and this specification. These parameters shall constitute the approved casting procedure and shall be used for production of subsequent castings and test specimens. If necessary to make any change to these parameters, vendor shall submit a statement of

49、the proposed change for purchaser reapproval. When requested, vendor shall also submit test specimens, sample castings, or both to purchaser for reapproval. 4.4.2.1 Production castings produced prior to receipt of purchasers approval shall be at vendors risk. SAE AMS 5401C Page 8 of 11 4.4.2.2 Control factors for producing castings and separately-cast specimens include, but are not limited to, the following fa