SAE AMS 5553G-2012 Nickel Sheet and Strip Low (0 02 max) Carbon Annealed (UNS N02201)《退火的低(最大0 02)碳镍制薄板材和带材》.pdf

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2012 SAE InternationalAll rights reserved. No part of this publi

3、cation may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (out

4、side USA)Fax: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/AMS5553GAEROSPACEMATERIALSPECIFICATIONAMS5553 REV. GIssued 1965-02Revised 2012-04Superseding

5、AMS5553FNickel, Sheet and StripLow (0.02 max) CarbonAnnealed(Composition similar to UNS N02201)RATIONALEAMS5553G removes a withdrawn chemical analysis standard (3.1), extends the applicable thickness range (Table 2), and is a Five Year Review and update of this specification.1. SCOPE1.1 FormThis spe

6、cification covers nickel in the form of sheet and strip.1.2 ApplicationThese products have been used typically for parts requiring excellent corrosion resistance, and/or strong magnetic properties, but usage is not limited to such applications.2. APPLICABLE DOCUMENTSThe issue of the following docume

7、nts in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document h

8、as been specified, the last published issue of that document shall apply.2.1 SAE PublicationsAvailable from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.AMS2262 Tolerances, Nickel, Nickel Al

9、loy, and Cobalt Alloy Sheet, Strip, and PlateAMS2269 Chemical Check Analysis Limits, Nickel, Nickel Alloys, and Cobalt AlloysSAE AMS5553G Page 2 of 5AMS2371 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steels and Alloys, Wrought Products and Forging StockAMS2807 Identificatio

10、n, Carbon and Low-Alloy Steels, Corrosion and Heat-Resistant Steels and Alloys, Sheet, Strip, Plate, and Aircraft TubingAS4194 Sheet and Strip Surface Finish Nomenclature2.2 ASTM PublicationsAvailable from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Te

11、l: 610-832-9585, www.astm.org.ASTM A 480/A 480M Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and StripASTM E 8/E 8M Tension Testing of Metallic MaterialsASTM E 18 Rockwell Hardness of Metallic MaterialsASTM E 384 Knoop and Vickers Hardness of Materials3. TECHNICAL REQUIREMENTS3.1 Com

12、positionShall conform to the percentages by weight shown in Table 1, determined by spectrochemical methods, or by other analytical methods acceptable to purchaser.TABLE 1 - COMPOSITIONElement min maxNickelCarbonManganeseSiliconSulfurCobaltIronCopper99.0-0.020.350.350.0101.000.400.253.1.1 Check Analy

13、sisComposition variations shall meet the applicable requirements of AMS2269.3.2 ConditionCold rolled, annealed, and, unless annealing is performed in an atmosphere yielding a bright finish, descaled having a surface appearance in accordance with ASTM A 480/A 480M and AS4194 comparable to 3.2.1.1 or

14、3.2.1.2 as applicable.SAE AMS5553G Page 3 of 53.2.1 SheetNo. 2D finish.3.2.2 StripNo. 1 strip finish.3.3 PropertiesThe product shall conform to the following requirements:3.3.1 Tensile PropertiesShall be as shown in Table 2, determined in accordance with ASTM E 8/E 8M.TABLE 2A - TENSILE PROPERTIES,

15、INCH/POUND UNITSNominalThicknessInchTensileStrengthksi, minYield Strengthat 0.2% OffsetksiElongationin 2 inches or 4D%, min0.001 to 0.010, excl0.010 to 0.015, inclOver 0.015 to 0.049, inclOver 0.049 to 0.109, inclOver 0.109 to 0.250, incl45.050505050-30.0, max12.0, min 12.0, min 12.0, min -30303540T

16、ABLE 2B - TENSILE PROPERTIES, SI UNITSNominalThicknessMillimetersTensileStrengthMPa, minYield Strengthat 0.2% OffsetMPaElongationin 50.8 mm or 4D%, min0.03 to 0.25, excl0.25 to 0.38, inclOver 0.38 to 1.24, inclOver 1.24 to 2.77, inclOver 2.77 to 6.35, incl310345345345345-207, max83, min 83, min 83,

17、min -303035403.3.2 HardnessShall be not higher than 66 HRB, or equivalent (See 8.2), determined in accordance with ASTM E 18; for thin gages where superficial hardness testing is impractical, microhardness testing in accordance with ASTM E 384 may be used. Product shall not be rejected on the basis

18、of hardness if the tensile properties of 3.3.1 are acceptable, determined on product takenfrom the same sample as that with nonconforming hardness or from another sample with similar nonconforming hardness.3.4 QualityThe product, as received by purchaser, shall be uniform in quality and condition, s

19、ound, and free from foreign materials and from imperfections detrimental to usage of the product.SAE AMS5553G Page 4 of 53.5 TolerancesShall conform to all applicable requirements of AMS2262.4. QUALITY ASSURANCE PROVISIONS4.1 Responsibility for InspectionThe vendor of the product shall supply all sa

20、mples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements.4.2 Classification of TestsAll technical requireme

21、nts are acceptance tests and shall be performed on each heat or lot as applicable.4.3 Sampling and TestingShall be in accordance with AMS2371.4.4 ReportsThe vendor of the product shall furnish with each shipment a report showing the results of tests for chemical composition of each heat and for tens

22、ile properties and hardness of each lot, and stating that the product conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers, AMS5553G, size, and quantity.4.5 Resampling and RetestingShall be in accordance with AMS2371.5. PREPARATION F

23、OR DELIVERY5.1 IdentificationShall be in accordance with AMS2807.5.2 PackagingThe product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure c

24、arrier acceptance and safe delivery.6. ACKNOWLEDGMENTA vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders.7. REJECTIONSProduct not conforming to this specification, or to modifications authorized by purchaser, will be subje

25、ct to rejection.SAE AMS5553G Page 5 of 58. NOTES8.1 A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document titl

26、e indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only.8.2 Hardness conversion tables for metals are presented in ASTM E 140.8.3 Terms used in AMS are clarified in

27、 ARP1917.8.4 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information.8.5 Purchase documents should specify not less than the following:AMS5553GProduct Form and size of product desiredQuantity of product desired.PREPARED BY AMS COMMITTEE “F“