SAE AMS 5562E-2010 Steel Corrosion and Heat Resistant Seamless Tubing 9 0Mn - 20Cr - 6 5Ni - 0 28N Solution Heat Treated (UNS S21904)《9 0Mn 20Cr 6 5Ni 0 28N溶液热处理的耐蚀和耐热无缝钢管》.pdf

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2010 SAE International All rights reserved. No part of this publication ma

3、y be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside US

4、A) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5562EAEROSPACEMATERIALSPECIFICATIONAMS5562 REV. E Issued 1974-06 Reaffirmed 2006-04 Revised

5、2010-08 Superseding AMS5562D Steel, Corrosion and Heat Resistant, Seamless Tubing 9.0Mn - 20Cr - 6.5Ni - 0.28N Solution Heat Treated UNS S21904 RATIONALEAMS5562E revises sampling and testing (4.3.2) and results from a Five Year Review and update of this specification. 1. SCOPE 1.1 Form This specific

6、ation covers a corrosion and heat resistant steel in the form of seamless tubing. 1.2 ApplicationThis tubing has been used typically for parts, such as fluid-conducting lines, requiring both corrosion and heat resistance, especially when such parts are welded or brazed during fabrication, and which

7、require strength higher than that of the 18 8 type steels, or require oxidation resistance up to 1100 F (593 C), but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification

8、to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE P

9、ublications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.AMS2243 Tolerances, Corrosion and Heat-Resistant Steel Tubing AMS2248 Chemical Check Analysis Limits, Corrosion and He

10、at-Resistant Steels and Alloys, Maraging and Other Highly-Alloyed Steels, and Iron Alloys AMS2371 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steels and Alloys, Wrought Products and Forging Stock SAE AMS5562E Page 2 of 6AMS2634 Ultrasonic Inspection, Thin Wall Metal Tubing A

11、MS2807 Identification, Carbon and Low-Alloy Steels, Corrosion and Heat-Resistant Steels and Alloys, Sheet, Strip, Plate, and Aircraft Tubing 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.or

12、g.ASTM A 262 Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels ASTM A 370 Mechanical Testing of Steel Products ASTM A 450/A 450M General Requirements for Carbon, Ferritic Alloy and Austenitic Alloy Steel Tubes ASTM E 353 Chemical Analysis of Stainless, Heat-Resisting, M

13、araging, and Other Similar Chromium-Nickel-Iron Alloys ASTM E 426 Electromagnetic (Eddy-Current) Examination of Seamless and Welded Tubular Products, Austenitic Stainless Steel and Similar Alloys ASTM E 1417 Liquid Penetrant Testing 3. TECHNICAL REQUIREMENTS 3.1 CompositionShall conform to the perce

14、ntages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E 353, by spectrochemical methods, or by other analytical methods acceptable to purchaser. TABLE 1 - COMPOSITION Element min max Carbon - 0.04 Manganese 8.00 10.00 Silicon - 1.00 Phosphorus - 0.060 Sulfur -

15、 0.030 Chromium 19.00 21.50 Nickel 5.50 7.50 Nitrogen 0.15 0.40 Molybdenum - 0.75 Copper - 0.75 3.1.1 Check Analysis Composition variations shall meet the applicable requirements of AMS2248. 3.2 ConditionSolution heat treated, and, unless solution heat treatment is performed in an atmosphere yieldin

16、g a bright finish, pickled as required or passivated. SAE AMS5562E Page 3 of 63.3 Fabrication Tubing shall be produced by a seamless process. Any surface finishing operation applied to remove objectional sets and surface blemishes shall be performed prior to final solution heat treatment. A light po

17、lish to improve external surface appearance may be employed after solution heat treatment and, if performed, the product shall be subsequently passivated.3.4 PropertiesTubing shall conform to the following requirements: 3.4.1 Tensile Properties Shall be as shown in Table 2, determined in accordance

18、with ASTM A 370. TABLE 2 - MINIMUM TENSILE PROPERTIES Property Value Tensile Strength 90.0 ksi (621 MPa) Yield Strength at 0.2% Offset 50.0 ksi (345 MPa) Elongation in 2 Inches (50.8 mm)Strip Specimens Full Tube Specimens40% 45% 3.4.2 Flarability Specimens as in 4.3.1 shall withstand flaring at room

19、 temperature, without formation of cracks or other visible defects, by being forced axially with steady pressure over a hardened and polished tapered steel pin having a 74-degree included angle to produce a flare having a permanent expanded OD not less than shown in Table 3. TABLE 3A - FLARABILITY,

20、INCH/POUND UNITS Nominal OD InchesExpanded OD InchesNominal OD InchesExpanded OD Inches0.125 0.200 0.750 0.937 0.188 0.302 1.000 1.187 0.250 0.359 1.250 1.500 0.312 0.421 1.500 1.721 0.375 0.484 1.750 2.106 0.500 0.656 2.000 2.356 0.625 0.781 TABLE 3B - FLARABILITY, SI UNITS Nominal OD MillimetersEx

21、panded OD MillimetersNominal OD MillimetersExpanded OD Millimeters3.18 5.08 19.05 23.80 4.78 7.67 25.40 30.15 6.35 9.12 31.75 38.10 7.92 10.69 38.10 43.71 9.52 12.29 44.45 53.49 12.70 16.66 50.80 59.84 15.88 19.84 3.4.2.1 Tubing with nominal OD between any two standard sizes shown in Table 3 shall t

22、ake the same percentage flare as shown for the larger of the two sizes. SAE AMS5562E Page 4 of 63.4.3 Pressure Test The tubing shall show no bulges, leaks, pinholes, cracks, or other defects when subjected to an internal hydrostatic pressure (P), except that a diametric permanent set of 0.002 inch p

23、er inch (0.002 mm/mm) of diameter is acceptable. The hydrostatic pressure (P) shall be determined using Equation 1: 2222DdPSDd=+(Eq. 1)where:P = Test pressure in ksi (MPa) S = Minimum yield strength from 3.4.1 D = Nominal OD d = Nominal ID 3.4.4 Susceptibility to Intergranular Attack Specimens from

24、tubing, after sensitizing treatment, shall pass the intergranular corrosion test performed in accordance with ASTM A 262, Practice E. After exposure, tubing shall be tested in accordance with the flattening test requirements of ASTM A 450/A 450M. Samples shall be taken from tubing after final anneal

25、ing but may be taken prior to cold working. 3.5 QualityTubing, as received by purchaser, shall be uniform in quality and condition and shall have a finish conforming to the best practice for high quality aircraft tubing. It shall be smooth and free from grease, oil and other foreign matter, heavy sc

26、ale or oxide, burrs, seams, tears, grooves, laminations, slivers, pits, and other imperfections detrimental to usage of the tubing. Surface imperfections, such as handling marks, straightening marks, light mandrel and die marks, shallow pits, and scale pattern, will not be considered injurious if th

27、e imperfections are removable within the tolerances specified for wall thickness, but removal of such imperfections is not required. 3.5.1 Tubing shall be free from grease or other foreign matter. Metallic flakes or particles shall not be collected by a clean, white cloth drawn through the length of

28、 the bore of a test sample. Discoloration of the cloth, without the presence of flakes or particles, is acceptable. 3.5.2 When specified, tubing shall be subjected to fluorescent penetrant testing in accordance with ASTM E 1417, to ultrasonic inspection in accordance with AMS2634, to electromagnetic

29、 (eddy- current) inspection in accordance with ASTM E 426, or to any combination thereof. Tubing shall meet the requirements of 3.5 and other acceptance criteria established by the cognizant engineering organization (See 8.4). 3.6 Tolerances Shall conform to all applicable requirements of AMS2243. 4

30、. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The vendor of tubing shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensu

31、re that the tubing conforms to specified requirements. SAE AMS5562E Page 5 of 64.2 Classification of Tests 4.2.1 Acceptance Tests Composition (3.1), tensile properties (3.4.1), nondestructive inspection when specified (3.5.2), and tolerances (3.6) are acceptance tests and shall be performed on each

32、heat or lot as applicable. 4.2.2 Periodic Tests Flarability (3.4.2), pressure test (3.4.3), and susceptibility to intergranular attack (3.4.4) are periodic tests and shall be performed at a frequency selected by the vendor unless frequency of testing is specified by purchaser. 4.3 Sampling and Testi

33、ng Shall be in accordance with AMS2371 and the following: 4.3.1 Specimens for flarability test (3.4.2) shall be full tubes or sections cut from a tube. The end of the specimen to be flared shall be cut square, with the cut end smooth and free from burrs, but not rounded. 4.3.2 When nondestructive in

34、spection (3.5.2) is required, each length of tubing shall be inspected. 4.4 Reports The vendor of tubing shall furnish with each shipment a report showing the results of tests for composition of each heat and for tensile properties of each lot, and stating that the product conforms to the other tech

35、nical requirements. This report shall include the purchase order number, heat and lot numbers, AMS5562E, size, and quantity. 4.5 Resampling and Retesting Shall be in accordance with AMS2371. 5. PREPARATION FOR DELIVERY 5.1 Sizes Except when exact lengths or multiples of exact lengths are ordered, st

36、raight tubing will be acceptable in mill lengths of 6 to 20 feet (1.8 to 6.1 m) but not more than 10% of any shipment shall be supplied in lengths shorter than 10 feet (3 m). 5.2 IdentificationShall be in accordance with AMS2807.5.3 PackagingTubing shall be prepared for shipment in accordance with c

37、ommercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the tubing to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT A vendor shall mention this specification number and its revision letter in all quotati

38、ons and when acknowledging purchase orders. SAE AMS5562E Page 6 of 67. REJECTIONS Tubing not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 A change bar (l) located in the left margin is for the convenience of the user in loc

39、ating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications

40、, nor in documents that contain editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equiv

41、alents of the primary units and are presented only for information. 8.4 Purchase documents should specify not less than the following AMS5562ESize of tubing desired Quantity of tubing desired Methods for nondestructive testing and standards for acceptance, when specified (See 3.5.2). PREPARED BY AMS COMMITTEE “F“