SAE AMS 5690M-2015 Steel Corrosion and Heat Resistant Wire 17Cr - 12Ni - 2 5Mo (316) Solution Heat Treated (UNS S31600).pdf

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2015 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5690M AEROSPACE MATERIAL SPECIFICATION AMS5690 REV. M Issued 1939-12 Reaffirme

5、d 2010-05 Revised 2015-08 Superseding AMS5690L Steel, Corrosion and Heat Resistant, Wire 17Cr - 12Ni - 2.5Mo (316) Solution Heat Treated (Composition similar to UNS S31600) RATIONALE AMS5690M revises Reports (4.4) and is a Five Year Review and update of this specification. 1. SCOPE 1.1 Form This spe

6、cification covers a corrosion and heat resistant steel in the form of wire. 1.2 Application This wire has been used typically for woven wire screening, but usage is not limited to such application. 1.2.1 The former requirements of this specification for use as welding wire are embodied in AMS5692. W

7、hen AMS5690 is specified for welding wire, use AMS5692. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a sp

8、ecific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 87

9、7-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS2241 Tolerances, Corrosion and Heat-Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy Bars and Wire SAE INTERNATIONAL AMS5690M Page 2 of 4 AMS2248 Chemical Check Analysis Limits, Corrosion and Heat-Resistant

10、 Steels and Alloys, Maraging and Other Highly-Alloyed Steels, and Iron Alloys AMS2371 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steels and Alloys, Wrought Products and Forging Stock 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C7

11、00, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM E353 Chemical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nickel-Iron Alloys 3. TECHNICAL REQUIREMENTS 3.1 Composition Wire shall conform to the percentages by weight shown in Table 1, determi

12、ned by wet chemical methods in accordance with ASTM E353, by spectrochemical methods, or by other analytical methods acceptable to purchaser. Table 1 - Composition Element min max Carbon Manganese Silicon Phosphorus Sulfur Chromium Nickel Molybdenum Copper - - - - - 16.00 10.00 2.00 - 0.08 2.00 1.00

13、 0.040 0.030 18.00 14.00 3.00 0.75 3.1.1 Chemical analysis of initial ingot, bar, or rod stock before drawing is acceptable provided the processes used for drawing or rolling, annealing, and cleaning, are controlled to ensure continued conformance to chemical composition requirements. 3.1.2 Check An

14、alysis Composition variations shall meet the applicable requirements of AMS2248. 3.2 Condition Solution heat treated, free from continuous carbide network, and bright finished. 3.3 Properties Wire shall conform to the following requirements: 3.3.1 Bending Wire shall withstand, without cracking, bend

15、ing at room temperature flat on itself. SAE INTERNATIONAL AMS5690M Page 3 of 4 3.4 Quality Wire, as received by purchaser, shall be uniform in quality and condition, cylindrical, smooth, and free from kinks, twists, scrapes, splits, cold shuts, pits, and other imperfections detrimental to usage of t

16、he wire. 3.5 Tolerances Shall conform to AMS2241. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The producer of wire shall supply all samples for producers tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perf

17、orm any confirmatory testing deemed necessary to ensure that the wire conforms to specified requirements. 4.2 Classification of Tests All technical requirements are acceptance tests and shall be performed on each heat or lot as applicable. 4.3 Sampling and Testing Shall be in accordance with AMS2371

18、. 4.4 Reports The producer of wire shall furnish with each shipment a report showing the producers name and the country where the metal was melted (e.g., final melt in the case of metal processed by multiple melting operations), and the results of tests for chemical composition of each heat, and for

19、 bending of each lot, and stating that the wire conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers, AMS5690M, nominal size, and quantity. 4.5 Resampling and Retesting Shall be in accordance with AMS2371. 5. PREPARATION FOR DELIVERY

20、 5.1 Identification Coils or reels of wire shall be identified by a durable tag legibly marked with the purchase order number, AMS5690M, heat and lot numbers, nominal size, quantity, and manufacturers identification. Straight lengths shall be bundled or boxed and shall have attached to each bundle o

21、r box a tag marked with the above information. 5.2 Packaging Wire shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the wire to ensure carrier acceptance and safe

22、delivery. 5.2.1 Wire shall be supplied in coils, on reels, or in straight lengths, as ordered. 6. ACKNOWLEDGMENT A producer shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. SAE INTERNATIONAL AMS5690M Page 4 of 4 7. REJECTIONS W

23、ire not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 Revision Indicator A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have

24、 been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 Terms used in AMS are clarified in ARP1917. 8.3 Purchase documents should specify not less than the following: AMS5690M Size and form (coils, reels, or straight lengths) of wire desired Quantity of wire desired Special packaging, if required. PREPARED BY AMS COMMITTEE “F”