SAE AMS 5763E-2016 Steel Corrosion Resistant Bars Forgings Tubing and Rings 15Cr - 6 5Ni - 0 75Mo - 0 50Cb (Nb) - 1 5Cu Solution Heat Treated (UNS S45000).pdf

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2016 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5763E AEROSPACE MATERIAL SPECIFICATION AMS5763 REV. E Issued 1972-12 Reaffirme

5、d 2006-04 Revised 2016-08Superseding AMS5763D Steel, Corrosion Resistant Bars, Forgings, Tubing, and Rings 15Cr - 6.5Ni - 0.75Mo - 0.50Cb (Nb) - 1.5Cu Solution Heat Treated (Composition similar to UNS S45000)RATIONALE AMS5763E revises Condition (3.2.1.1.3), Properties (3.4.1.3), and Reports (4.4), a

6、nd is a Five Year Review and update of this specification. 1. SCOPE 1.1 Form This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash welded rings 8.0 inches (200 mm) and under in least nominal cross-sectional dimension, and stock of any siz

7、e for forging or flash welded rings (see 8.6). 1.2 Application These products have been used typically for parts requiring corrosion resistance approximating that of steels of the 18-8 types and high strength exceeding that of the 12 Cr martensitic types up to 700 F (370 C), but usage is not limited

8、 to such applications. 1.3 This steel can be used in the solution heat treated condition and is capable of being precipitation heat treated to tensile strengths as high as 180 ksi (1240 MPa), minimum. 1.4 Although this steel is relatively immune to stress-corrosion cracking, reference should be made

9、 to ARP1110 for recommended practices to minimize such conditions. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document

10、unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. SAE INTERNATIONAL AMS5763E Page 2 of 8 2.1 SAE Publications Available from SAE International, 400 Comm

11、onwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS2241 Tolerances, Corrosion and Heat-Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy Bars and Wire AMS2243 Tolerances, Corrosion and Heat-Resistant Steel Tu

12、bing AMS2248 Chemical Check Analysis Limits, Corrosion and Heat-Resistant Steels and Alloys, Maraging and Other Highly-Alloyed Steels, and Iron Alloys AMS2303 Steel Cleanliness, Aircraft Quality, Martensitic Corrosion-Resistant Steels, Magnetic Particle Inspection Procedure AMS2371 Quality Assurance

13、 Sampling and Testing, Corrosion and Heat-Resistant Steels and Alloys, Wrought Products and Forging Stock AMS2374 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steel and Alloy Forgings AMS2750 Pyrometry AMS2806 Identification Bars, Wire, Mechanical Tubing, and Extrusions, Carb

14、on and Alloy Steels and Corrosion and Heat-Resistant Steels and Alloys AMS2808 Identification Forgings AMS7490 Rings, Flash Welded, Corrosion and Heat-Resistant Austenitic Steels, Austenitic-Type Iron, Nickel, or Cobalt Alloys, or Precipitation-Hardenable Alloys ARP1110 Minimizing Stress Corrosion C

15、racking in Wrought Forms of Steels and Corrosion Resistant Steels and Alloys 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM A370 Mechanical Testing of Steel Products ASTM E353 Chem

16、ical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nickel-Iron Alloys SAE INTERNATIONAL AMS5763E Page 3 of 8 3. TECHNICAL REQUIREMENTS 3.1 Composition Shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM

17、 E353, by spectrochemical methods, or by other analytical methods acceptable to purchaser. Table 1 - Composition Element min max Carbon - 0.05 Manganese - 1.00 Silicon - 1.00 Phosphorus - 0.030 Sulfur - 0.030 Chromium 14.00 16.00 Nickel 6.00 7.00 Molybdenum 0.50 1.00 Columbium (Niobium) 8 x C 0.75 C

18、opper 1.25 1.75 3.1.1 Check Analysis Composition variations shall meet the applicable requirements of AMS2248. 3.2 Condition The product shall be supplied in the following condition: 3.2.1 Bars, Wire, Mechanical Tubing, Forgings, and Flash Welded Rings Solution heat treated. 3.2.1.1 Bars 3.2.1.1.1 R

19、ounds Solution heat treated and centerless ground. 3.2.1.1.2 Squares, Hexagons, and Flats Hot finished, solution heat treated, and descaled, or solution heat treated cold drawn, and descaled. 3.2.1.1.3 Bar shall not be cut from plate (also see 4.4.2). 3.2.1.2 Wire Solution heat treated and cold draw

20、n. 3.2.1.3 Mechanical Tubing Cold finished and solution heat treated. 3.2.1.4 Flash Welded Rings Shall not be supplied unless specified or permitted on purchasers part drawing. When supplied, they shall be manufactured in accordance with AMS7490. SAE INTERNATIONAL AMS5763E Page 4 of 8 3.2.2 Stock fo

21、r Forging or Flash Welded Rings As ordered by the forging or flash welded ring manufacturer. 3.3 Heat Treatment Bars, wire, forgings, mechanical tubing, and flash welded rings shall be solution heat treated by heating to 1900 F 25 F (1040 C 15 C), holding at heat for not less than 1 hour, and coolin

22、g rapidly. Pyrometry shall be in accordance with AMS2750. 3.4 Properties The product shall conform to the following requirements; hardness and tensile testing shall be conducted in accordance with ASTM A370: 3.4.1 Bars, Wire, Forgings, Mechanical Tubing, and Flash Welded Rings Shall be as follows on

23、 product 8.0 inch (200 mm) and under in least nominal cross-sectional dimensions. 3.4.1.1 As Solution Treated 3.4.1.1.1 Tensile Properties Shall meet the requirements shown in Table 2 and 3.4.1.1.1.2. 3.4.1.1.1.1 Bars, Forgings, Tubing, and Flash Welded Rings Table 2 - Minimum tensile properties Pro

24、perty Value Tensile Strength 125 ksi (860 MPa) Yield Strength at 0.2% Offset 95 ksi (655 MPa) Elongation in 4D 10% Reduction of Area 40% 3.4.1.1.1.2 Wire Not higher than 165.0 ksi (1135 MPa) or equivalent hardness (see 8.2). 3.4.1.1.2 Hardness Shall be as follows: 3.4.1.1.2.1 Bars Not higher than 31

25、1 HB, or equivalent (see 8.3), determined midway between surface and center. 3.4.1.1.2.2 Tubing, Flash Welded Rings, and Forgings Not higher than 311 HB, or equivalent (see 8.3). 3.4.1.2 After Precipitation Heat Treatment The product shall have the following properties after being precipitation heat

26、 treated by heating to 900 F 15 F (480 C 8 C), holding at heat for not less than 4 hours, and cooling in air: SAE INTERNATIONAL AMS5763E Page 5 of 8 3.4.1.2.1 Tensile Properties Shall be as shown in Table 3: Table 3 - Minimum tensile properties Property Value Tensile Strength 180 ksi (1240 MPa) Yiel

27、d Strength at 0.2% Offset 170 ksi (1170 MPa) Elongation in 4D 10% Reduction of Area 40% 3.4.1.2.2 Hardness Shall be not lower than 363 HB, or equivalent (see 8.3), but the product shall not be rejected on the basis of hardness if the tensile properties of 3.4.1.2.1 are acceptable, determined on spec

28、imens taken from the same sample as that with nonconforming hardness, or from another sample with similar nonconforming hardness. 3.4.1.3 Property requirements for product outside the range listed in 1.1 shall be agreed upon between purchaser and producer. 3.4.2 Forging Stock When a sample of stock

29、is forged to a test coupon and heat treated as in 3.3 and 3.4.1.2, specimens taken from the heat treated coupon shall conform to the requirements of 3.4.1.2.1 and 3.4.1.2.2. If specimens taken from the stock after heat treatment as in 3.3 and 3.4.1.2 conform to the requirements of 3.4.1.2.1 and 3.4.

30、1.2.2, the tests shall be accepted as equivalent to tests of a forged coupon. 3.4.3 Stock for Flash Welded Rings Specimens taken from the stock after heat treatment as in 3.3 and 3.4.1.2 shall conform to the requirements of 3.4.1.2.1 and 3.4.1.2.2. 3.5 Quality The product, as received by purchaser,

31、shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to usage of the product. 3.5.1 When specified, steel shall conform to AMS2303. 3.5.2 Forgings shall have substantially uniform macrostructure. Standards for acceptance may be agreed u

32、pon by purchaser and producer. 3.5.3 Grain flow of die forgings, except in areas which contain flash-line end grain, shall follow the general contour of the forgings, showing no evidence of reentrant flow. 3.6 Tolerances Shall be as follows: 3.6.1 Bars and Wire In accordance with AMS2241. 3.6.2 Mech

33、anical Tubing In accordance with AMS2243. SAE INTERNATIONAL AMS5763E Page 6 of 8 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The producer of the product shall supply all samples for producers tests and shall be responsible for the performance of all required tests. Purchaser re

34、serves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements. 4.2 Classification of Tests 4.2.1 Acceptance Tests The following are acceptance tests and shall be performed on each heat or lot as applicable: 4.2.1.1 C

35、omposition (3.1) of each heat. 4.2.1.2 Tensile properties (3.4.1.1.1) and hardness (3.4.1.1.2) of each lot of bars, wire, forgings, mechanical tubing, and flash welded rings as solution heat treated. 4.2.1.3 Macrostructure of forgings (3.5.2). 4.2.1.4 Tolerances (3.6) of bars, wire, and mechanical t

36、ubing. 4.2.2 Periodic Tests The following are periodic tests and shall be performed at a frequency selected by the producer unless frequency of testing is specified by purchaser: 4.2.2.1 Tensile properties (3.4.1.2.1) and hardness (3.4.1.2.2) of each lot of bars, wire, forgings, mechanical tubing, a

37、nd flash welded rings after precipitation heat treatment, and grain flow of die forgings (3.5.3). 4.2.2.2 Ability of forging stock (3.4.2) and stock for flash welded rings (3.4.3) to develop required properties. 4.3 Sampling and Testing Shall be as follows: 4.3.1 Bars, Wire, Mechanical Tubing, Flash

38、 Welded Rings, Forging Stock, and Stock for Flash Welded Rings In accordance with AMS2371. 4.3.2 Forgings In accordance with AMS2374. 4.4 Reports 4.4.1 The producer of bars, wire, forgings, mechanical tubing, and flash welded rings shall furnish with each shipment a report showing the producers name

39、 and the country where the metal was melted (e.g., final melt in the case of metal processed by multiple melting operations) and the results of tests for composition of each heat and for tensile properties and hardness of each lot, and stating the product conforms to the other technical requirements

40、. This report shall include the purchase order number, heat and lot numbers, AMS5763E, product form, size, and quantity. If forgings are supplied, statement of compliance with the uniform macrostructure requirement (if agreed upon) and the size and melt source of stock used to make the forgings shal

41、l also be included. SAE INTERNATIONAL AMS5763E Page 7 of 8 4.4.2 Report the nominal metallurgically worked cross sectional size and the cut size, if different (also see 3.2.1.1.3). 4.4.3 When the product is outside the range covered by 1.1, the report shall contain a statement to that effect. 4.4.4

42、The producer of forging stock shall furnish with each shipment a report showing the producers name and the country where the metal was melted (e.g., final melt in the case of metal processed by multiple melting operations) and the results of tests for composition, and when specified, magnetic partic

43、le inspection of each heat. This report shall include the purchase order number, heat number, ASM5763E, size and quantity. 4.5 Resampling and Retesting Shall be as follows: 4.5.1 Bars, Wire, Mechanical Tubing, Flash Welded Rings, Forging Stock, and Stock for Flash Welded Rings In accordance with AMS

44、2371. 4.5.2 Forgings In accordance with AMS2374. 5. PREPARATION FOR DELIVERY 5.1 Sizes Except when exact lengths or multiples of exact lengths are ordered, straight bars, wire, and tubing will be acceptable in mill lengths of 6 to 20 feet (2 to 6 m) but not more than 10% of any shipment shall be sup

45、plied in lengths shorter than 10 feet (3 m). 5.2 Identification Shall be as follows: 5.2.1 Bars, Wire, and Mechanical Tubing In accordance with AMS2806. 5.2.2 Forgings In accordance with AMS2808. 5.2.3 Flash Welded Rings and Stock for Forging or Flash Welded Rings As agreed upon by purchaser and pro

46、ducer. 5.3 Packaging The product shall be prepared for shipment in accordance with commercial practice and in compliance with applicable rules and regulations pertaining to the handling, packaging, and transportation of the product to ensure carrier acceptance and safe delivery. 6. ACKNOWLEDGMENT A

47、producer shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Material not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. SAE INTERNATIONAL AMS5763E Page 8

48、 of 8 8. NOTES 8.1 Revision Indicator A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a

49、complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 Tensile strength to hardness conversions are presented in ASTM A370. 8.3 Hardness conversion tables for metals are presented in ASTM E140. 8.4 Terms used in AMS are clarified in ARP1917. 8.5 Dime