SAE AMS 5774E-2002 Steel Corrosion and Heat-Resistant Welding Wire 16 5Cr - 4 5Ni - 2 9Mo - 0 10N (UNS S35080)《UNS S35080 含16 5Cr-4 5Ni-2 9Mo-0 10N的耐腐蚀耐热钢焊丝》.pdf

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report isentirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr

2、om, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2015 SAE InternationalAll rights reserved. No part of this public

3、ation may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (outs

4、ide USA)Fax: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/AMS5774EAEROSPACEMATERIAL SPECIFICATIONAMS5774 REV. EIssued 1960-01Revised 2002-11Reaffirmed 2

5、015-12Superseding AMS5774DSteel, Corrosion and Heat-Resistant, Welding Wire16.5Cr - 4.5Ni - 2.9Mo - 0.10N(Composition similar to UNS S35080)RATIONALEAMS5774E has been reaffirmed to comply with the SAE five-year review policy.1. SCOPE:1.1 Form: This specification covers a corrosion and heat-resistant

6、 steel in the form of welding wire.1.2 Application: This wire has been used typically as filler metal for gas-tungsten-arc or gas-metal-arc welding of parts fabricated from steels or alloys of similar composition requiring joints with strength and corrosion resistance comparable to those of the basi

7、s metal, but usage is not limited to such applications.2. APPLICABLE DOCUMENTS: The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a sp

8、ecific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply.2.1 SAE Publications: Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001 or www.sae.org.AMS 224

9、8 Chemical Check Analysis Limits, Corrosion and Heat-Resistant Steels and Alloys, Maraging and Other Highly-Alloyed Steels, and Iron AlloysAMS 2371 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steels and Alloys, Wrought Products and Forging StockAMS 2813 Packaging and Marking

10、 of Packages of Welding Wire, Standard MethodAMS 2814 Packaging and Marking of Packages of Welding Wire, Premium Quality2.1 (Continued):AMS 2816 Identification, Welding Wire, Tab Marking MethodAMS 2819 Identification, Welding Wire, Direct Color Code SystemARP1876 Weldability Test for Weld Filler Met

11、al WireARP4926 Alloy Verification and Chemical Composition Inspection of Welding Wire2.2 ASTM Publications: Available from ASTM, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959 or www.astm.org.ASTM E 353 Chemical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nic

12、kel-Iron Alloys3. TECHNICAL REQUIREMENTS: 3.1 Wire Composition: Shall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E 353, by spectrochemical methods, or by other analytical methods acceptable to purchaser.3.1.1 Chemical analysis of

13、 initial ingot, bar, or rod stock before drawing is acceptable provided processes used for drawing or rolling, annealing, and cleaning are controlled to ensure continued conformance to composition requirements.3.1.1.1 Carbon and nitrogen shall also be determined periodically on finished wire (See 4.

14、2.2).3.1.2 Check Analysis: Composition variations shall meet the applicable requirements of AMS 2248.TABLE 1 - CompositionElement min maxCarbon (3.1.1.1) 0.08 0.12Manganese 0.50 1.25Silicon - 0.50Phosphorus - 0.040Sulfur - 0.030Chromium 16.00 17.00Nickel 4.00 5.00Molybdenum 2.50 3.25Nitrogen (3.1.1.

15、1) 0.07 0.13SAE INTERNATIONAL AMS5774E Page 2 of 6_ 3.2 Condition: Cold worked, bright finish, in a temper and with a surface finish which will provide proper feeding of the wire in machine welding equipment.3.3 Fabrication: 3.3.1 Wire shall be formed from rod or bar descaled by a process which does

16、 not affect the composition of the wire. Surface irregularities inherent with a forming process that does not tear the wire surfaces are acceptable provided the wire conforms to the tolerances of 3.6.3.3.2 Butt welding is permissible provided both ends to be joined are alloy verified using a method

17、capable of distinguishing the alloy from all other alloys processed in the facility, or the repair is made at the wire processing station. The butt weld shall not interfere with uniform, uninterrupted feeding of the wire in machine welding.3.3.3 In-process annealing, if required, between cold rollin

18、g or drawing operations, shall be performed in vacuum or protective atmospheres to ensure freedom from surface oxidation and absorption of other extraneous elements.3.3.4 Residual elements, drawing compounds, oxides, dirt, oil, dissolved gasses and other foreign materials picked up during wire proce

19、ssing that can adversely affect the welding characteristics, the operation of the equipment, or the properties of the weld metal, shall be removed by cleaning processes that will neither result in pitting nor cause gas absorption by the wire or deposition of substances harmful to welding operations.

20、3.4 Properties: Wire shall conform to the following requirements:3.4.1 Weldability: Melted wire shall flow smoothly and evenly during welding and shall produce acceptable welds. ARP1876 may be used to resolve disputes.3.4.2 Spooled Wire: Shall conform to 3.4.2.1 and 3.4.2.2.3.4.2.1 Cast: Wire, wound

21、 on standard 12-inch (305-mm) diameter spools, shall have imparted to it a curvature such that a specimen sufficient in length to form one loop with a 1-inch (25-mm) overlap, when cut from the spool and laid on a flat surface, shall form a circle 15 to 50 inches (381 to 1270 mm) in diameter.3.4.2.2

22、Helix: The specimen on which cast was determined, when laid on a flat surface and measured between adjacent turns, shall show a vertical separation not greater than 1 inch (25 mm).SAE INTERNATIONAL AMS5774E Page 3 of 6_ 3.5 Quality: Wire, as received by purchaser, shall be uniform in quality and con

23、dition, sound, and free from foreign materials and from imperfections detrimental to welding operations, operation of welding equipment, or properties of the deposited weld metal.3.6 Sizes and Tolerances: Wire shall be supplied in the sizes and to the tolerances shown in 3.6.1 and 3.6.2.3.6.1 Diamet

24、er: Shall be as shown in Table 2.3.6.2 Length: Cut lengths shall be furnished in 18, 27, or 36-inch (457, 686, or 914-mm) lengths, as ordered, and shall not vary more than +0, -0.5 inch (-13 mm) from the length ordered.4. QUALITY ASSURANCE PROVISIONS: 4 .1 Responsibility for Inspection: The vendor o

25、f wire shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the wire conforms to specified requirements.TABLE 2A - Sizes and Diamet

26、er Tolerances, Inch/Pound UnitsFormNominal DiameterInchToleranceInchPlus and MinusCut Lengths 0.030, 0.035, 0.045 0.001Cut Lengths 0.062, 0.078, 0.094, 0.125, 0.156, 0.187 0.002Spools 0.007, 0.010, 0.015 0.0005Spools 0.020, 0.030, 0.035, 0.045 0.001Spools 0.062, 0.078, 0.094 0.002TABLE 2B - Sizes an

27、d Diameter Tolerances, SI UnitsFormNominal DiameterMillimetersToleranceMillimeterPlus and MinusCut Lengths 0.76, 0.89, 1.14 0.025Cut Lengths 1.57, 1.98, 2.39, 3.18, 3.96, 4.75 0.05Spools 0.18, 0.25, 0.38 0.013Spools 0.51, 0.76, 0.89, 1.14 0.025Spools 1.57, 1.98, 2.39 0.05SAE INTERNATIONAL AMS5774E P

28、age 4 of 6_ 4.2 Classification of Tests: 4.2.1 Acceptance Tests: Composition (3.1.1), sizes and tolerances (3.6), and alloy verification (5.2) are acceptance tests and shall be performed on each heat or lot as applicable.4.2.2 Periodic Tests: Determination of carbon and nitrogen on finished wire (3.

29、1.1.1), weldability (3.4.1), cast (3.4.2.1) and helix (3.4.2.2) are periodic tests and shall be performed at a frequency selected by the vendor unless frequency of testing is specified by purchaser.4.3 Sampling and Testing: Shall be in accordance with AMS 2371 and as specified herein.4.4 Reports: Th

30、e vendor of wire shall furnish with each shipment a report showing the results of tests for composition of each heat and stating that the wire conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers, AMS 5774E, nominal size, and quantit

31、y.4.5 Resampling and Retesting: Shall be in accordance with AMS 2371.5. PREPARATION FOR DELIVERY: 5.1 Wire shall be supplied either on spools in one continuous length for machine welding or in cut lengths for manual welding, as ordered. Wire on each spool or in each package of cut lengths shall be f

32、rom the same heat of steel.5.2 Alloy Verification: Wire on each spool or in each package of cut lengths shall be alloy verified by a method acceptable to purchaser. The alloy verification procedures of ARP4926 are recommended.5.2.1 An 8-inch (203-mm) length of wire shall be made accessible at both e

33、nds of each spool for alloy verification.5.3 Identification: Shall be in accordance with AMS 2816 unless AMS 2819 or another method is specified by purchaser.5.4 Packaging and Marking: Shall be in accordance with AMS 2813 unless AMS 2814 or another method is specified by purchaser.SAE INTERNATIONAL

34、AMS5774E Page 5 of 6_ 6. ACKNOWLEDGMENT: A vendor shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders.7. REJECTIONS: Wire not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejecti

35、on.8. NOTES: 8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of a specification. An (R) symbol to the left of the document title indicates a complete revision o

36、f the specification, including technical revision. Change bars and (R) are not used in original publications, nor in specifications that contain editorial changes only.8.2 Terms used in AMS are clarified in ARP1917.8.3 Dimensions in inch/pound units are primary; dimensions in SI units are shown as t

37、he approximate equivalents of the primary units and are presented only for information.8.4 Purchase documents should specify not less than the following:AMS 5774ESize and form (spools or cut lengths) of wire desiredLength of cut lengths or weight of spools desiredQuantity of wire desired.PREPARED UNDER THE JURISDICTION OF AMS COMMITTEE “ F”SAE INTERNATIONAL AMS5774E Page 6 of 6_