SAE AMS 5798H-2016 Nickel Alloy Corrosion and Heat-Resistant Welding Wire 47 5Ni - 22Cr - 1 5Co - 9 0Mo - 0 60W - 18Fe (UNS N06002).pdf

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2016 SAE InternationalAll rights reserved. No part of this publi

3、cation may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (out

4、side USA)Fax: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/AMS5798H AEROSPACEMATERIAL SPECIFICATIONAMS5798 REV. HIssued 1958-04Revised 2016-01Supersedin

5、g AMS5798GNickel Alloy, Corrosion and Heat-Resistant, Welding Wire47.5Ni - 22Cr - 1.5Co - 9.0Mo - 0.60W - 18Fe(Composition similar to UNS N06002)RATIONALEAMS5798H has been updated to incorporate the standard quality requirements of AMS materials as the ordering requirements for AWS specified wire, a

6、nd is a Five Year Review and update of this specification.1. SCOPE1.1 FormThis specification covers a corrosion and heat-resistant nickel alloy in the form of welding wire.1.2 Application This wire has been used typically as filler metal for gas-tungsten-arc or gas-metal-arc welding of parts fabrica

7、ted from alloys of similar or dissimilar composition, but usage is not limited to such applications.2. APPLICABLE DOCUMENTSThe issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a su

8、bsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply.2.1 SAE Publications Available from SAE International, 400 Commonwealth

9、 Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org.AMS2813 Packaging and Marking of Packages of Welding Wire, Standard MethodAMS2814 Packaging and Marking of Packages of Welding Wire, Premium QualityAMS2816 Identification, Weldi

10、ng Wire, Tab Marking MethodAMS2819 Identification, Welding Wire, Direct Color Code SystemARP4926 Alloy Verification and Chemical Composition Inspection of Welding WireSAE INTERNATIONAL AMS5798H Page 2 of 42.2 AWS Publications Available from American Welding Society, 8669 NW 36 Street, #130, Miami, F

11、L 33166-6672, Tel: 1-800-443-9353 or 305-443-9353, www.aws.org.AWS A5.01 Welding Consumables Procurement of Filler Metals and FluxesAWS A5.14 Specification for Nickel and Nickel-Alloy Bare Welding Electrodes and Rods3. TECHNICAL REQUIREMENTS 3.1 Wire shall meet the technical requirements of AWS A5.1

12、4 ErNiCrMo-2 with the following additional chemistry controls:3.1.1 Boron maximum: 0.010 percent. 3.2 Sizes and Tolerances Wire shall be supplied in the sizes and to the tolerances shown in AWS A5.14. Smaller diameter wires when ordered shall be supplied in sizes and tolerances shown in Table 1.Tabl

13、e 1A - Sizes and diameter tolerances, inch/pound unitsFormNominal DiameterInchToleranceInchPlusToleranceInchMinusCut Lengths 0.030, 0.035, 0.045 0.001 0.002Spools 0.007, 0.010, 0.015 0.0005 0.0005Table 1B - Sizes and diameter tolerances, SI unitsFormNominal DiameterMillimetersToleranceMillimeterPlus

14、ToleranceMillimeterMinusCut Lengths 0.76, 0.89, 1.14 0.025 0.05Spools 0.18, 0.25, 0.38 0.013 0.0134. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for InspectionThe producer of wire shall supply all samples for producers tests and shall be responsible for the performance of all required tests. Pur

15、chaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the wire conforms to specified requirements.4.2 Classification of Tests4.2.1 Acceptance TestsComposition (3.1), sizes and tolerances (3.2), and alloy verification (5.2) are acceptance tests an

16、d shall be performed oneach heat or lot as applicable.SAE INTERNATIONAL AMS5798H Page 3 of 44.3 Sampling and TestingShall be in accordance with AWS A5.01 S3, testing schedule 5 or J.4.4 ReportsThe producer of wire shall furnish with each shipment a report showing the results of tests for composition

17、 of each heat andstating that the wire conforms to the other technical requirements. This report shall include the purchase order number, heatand lot numbers, AMS5798H, nominal size, and quantity.4.5 Resampling and Retesting Shall be in accordance with AWS A5.01.5. PREPARATION FOR DELIVERY5.1 Wire s

18、hall be supplied either on spools in one continuous length for machine welding or in cut lengths for manual welding, as ordered. Wire on each spool or in each package of cut lengths shall be from the same heat of steel.5.2 Alloy Verification5.2.1 Wire from each spool or package of cut lengths shall

19、be alloy verified by a method acceptable to purchaser and producer. The alloy verification methods of ARP4926 are recommended.5.2.2 An 8 inch (203 mm) length of wire shall be made accessible at both ends of each spool for alloy verification.5.3 IdentificationShall be in accordance with AMS2816 unles

20、s AMS2819 or another method is specified by purchaser.5.4 Packaging and MarkingShall be in accordance with AMS2813 unless AMS2814 or another method is specified by purchaser.6. ACKNOWLEDGMENT A producer shall mention this specification number and its revision letter in all quotations and when acknow

21、ledging purchase orders.7. REJECTIONSWire not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection.8. NOTES8.1 Revision IndicatorA change bar (l) located in the left margin is for the convenience of the user in locating areas where technical rev

22、isions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain

23、 editorial changes only.SAE INTERNATIONAL AMS5798H Page 4 of 48.2 Terms used in AMS are clarified in ARP1917.8.3 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate

24、equivalents of the primary units and are presented only for information.8.4 Purchase documents should specify not less than the following:AMS5798HSize and form (spools or cut lengths) of wire desiredLength of cut lengths or weight of spools desiredQuantity of wire desired.PREPARED BY AMS COMMITTEE “F“