SAE AMS 6468E-2013 Steel Welding Wire 1 0Cr - 10Ni - 3 8Co - 0 45Mo - 0 08V (0 14 - 0 17C) Vacuum Melted Environment Controlled Packaging (UNS K91461)《用作环保控制包装的真空熔炼钢焊丝1 0Cr 10Ni 3 .pdf

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions.Copyright 2013 SAE InternationalAll rights reserved. No part of this publication may b

3、e reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (outside USA)Fax

4、: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/AMS6468EAEROSPACEMATERIALSPECIFICATIONAMS6468 REV. EIssued 1978-04Reaffirmed 2008-04Revised 2013-05Supers

5、eding AMS6468DSteel, Welding Wire1.0Cr - 10Ni - 3.8Co - 0.45Mo - 0.08V (0.14 - 0.17C)Vacuum Melted, Environment Controlled Packaging(Composition Similar to UNS K91461)RATIONALEAMS6468E results from a Five Year Review and update of this document.1. SCOPE1.1 FormThis specification covers an alloy stee

6、l in the form of welding wire.1.2 ApplicationThis wire has been used typically as filler metal for gas-tungsten-arc and gas-metal-arc welding of low-alloy steels having similar composition and requiring a combination of high strength and high notch toughness without the need for post-weld heat treat

7、ment, but usage is not limited to such applications.2. APPLICABLE DOCUMENTSThe issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specifi

8、c document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply.2.1 SAE PublicationsAvailable from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7

9、323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.AMS2259 Chemical Check Analysis Limits, Wrought Low-Alloy and Carbon SteelsAMS2300 Steel Cleanliness, Premium Aircraft-Quality, Magnetic Particle Inspection ProcedureAMS2370 Quality Assurance Sampling and Testing, Carbon and Low-

10、Alloy Steel Wrought Products and Forging StockAMS2813 Packaging and Marking of Packages of Welding Wire, Standard MethodSAE AMS6468E Page 2 of 6AMS2814 Packaging and Marking of Packages of Welding Wire, Premium QualityAMS2816 Identification, Welding Wire, Tab Marking MethodAMS2819 Identification, We

11、lding Wire, Direct Color Code SystemAMS6523 Steel, Sheet, Strip, and Plate, 0.75Cr - 9.0Ni - 4.5Co - 1.0Mo - 0.09V (0.17 - 0.23C), Vacuum Consumable Electrode Melted, AnnealedARP1876 Weldability Test for Weld Filler Metal WireARP4926 Alloy Verification and Chemical Composition Inspection of Welding

12、Wire2.2 ASTM PublicationsAvailable from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM D 2650 Chemical Composition of Gasses by Mass SpectrometryASTM E 350 Chemical Analysis of Carbon Steel, Low-Alloy Steel, Silicon El

13、ectrical Steel, Ingot Iron, and Wrought IronASTM E 1032 Radiographic Examination of WeldmentsASTM E 1820 Measurement of Fracture Toughness3. TECHNICAL REQUIREMENTS3.1 Wire CompositionShall conform to the percentages by weight shown in Table 1, determined by wet chemical methods in accordance withAST

14、M E 350, by spectrochemical methods, or by other analytical methods acceptable to purchaser.TABLE 1 COMPOSITIONElement min maxCarbon (3.1.1.1) 0.14 0.17Manganese 0.40 0.55Silicon 0.15 0.25Phosphorus - 0.006Sulfur - 0.005Chromium 0.90 1.05Nickel 9.75 10.25Cobalt 3.50 4.00Molybdenum 0.40 0.50Vanadium

15、0.06 0.10Copper - 0.10Oxygen (3.1.1.1) - 0.0025 (25 ppm)Nitrogen (3.1.1.1) - 0.0050 (50 ppm)Hydrogen (3.1.1.1) - 0.0005 ( 5 ppm)3.1.1 Chemical analysis of initial ingot, bar, or rod stock before drawing, other than those analyses required to be done on the finished wire, is acceptable provided the p

16、rocesses used for drawing or rolling, annealing, and cleaning are controlled to ensure continued conformance to requirements.3.1.1.1 Carbon, oxygen, nitrogen, and hydrogen shall also be determined periodically on finished wire (See 4.2.2).SAE AMS6468E Page 3 of 63.1.1.2 The hydrogen content of the w

17、ire shall be determined at final diameter in accordance with ASTM D 2650.3.1.2 Check AnalysisComposition variations shall meet the applicable requirements of AMS2259.3.2 Melting PracticeSteel shall be vacuum induction melted; it may be re-melted using consumable electrode vacuum practice (VAR) in th

18、e remelt cycle, but remelting is not required.3.2.1 Steel shall be premium aircraft-quality conforming to AMS2300.3.3 ConditionCold worked, bright finish, in a temper and with a surface finish which will provide proper feeding of the wire in machine welding equipment.3.4 Fabrication3.4.1 In-process

19、annealing, if required between cold rolling or drawing operations, shall be performed in vacuum or protective atmosphere to avoid surface oxidation and adsorption of other extraneous elements.3.4.2 Butt welding is permissible provided both ends to be joined are either alloy verified using a method o

20、r methods capable of distinguishing the alloy from all other alloys processed in the facility, or the repair is made at the wire processing station. The butt weld shall not interfere with uniform, uninterrupted feeding of the wire in machine welding equipment.3.4.3 Drawing compounds, oxides, dirt, o

21、il, and other foreign materials shall be removed by cleaning processes which will neither result in pitting nor cause gas absorption by the wire or deposition of substances harmful to welding operations.3.4.4 Residual elements and dissolved gasses picked up during wire processing that can adversely

22、affect the welding characteristics, the operation of the equipment, or the properties of weld metal shall be removed.3.5 PropertiesWire shall conform to the following requirements:3.5.1 WeldabilityMelted wire shall flow smoothly and evenly during welding and shall produce acceptable welds. ARP1876 m

23、ay be used to resolve disputes.3.5.2 Spooled WireShall conform to 3.5.2.1 and 3.5.2.2.3.5.2.1 CastWire, wound on standard 12-inch (305-mm) diameter spools, shall have imparted to it a curvature such that a specimen sufficient in length to form one loop with a 1-inch (25-mm) overlap, when cut from th

24、e spool and laid on a flat surface, shall form a circle 15 to 50 inches (381 to 1270 mm) in diameter.SAE AMS6468E Page 4 of 63.5.2.2 HelixThe specimen on which cast was determined, when laid on a flat surface and measured between adjacent turns, shall show a vertical separation not greater than 1 in

25、ch (25 mm).3.5.3 Fracture ToughnessWhen specified by purchaser, test specimens prepared as in 4.3.1 shall be fracture toughness tested in accordance with ASTM E 1820. Standards for acceptance for fracture toughness, when specified, shall be as agreed upon by purchaser and vendor.3.6 QualityWire, as

26、received by purchaser, shall be uniform in quality and condition, sound, and free from foreign materials and from imperfections detrimental to welding operations, operation of welding equipment, or properties of the deposited weld metal.3.7 Sizes and TolerancesWire shall be supplied in the sizes and

27、 to the tolerances shown in 3.7.1 and 3.7.2.3.7.1 DiameterShall be as shown in Table 2.TABLE 2A - SIZES AND DIAMETER TOLERANCES, INCH/POUND UNITSFormNominal DiameterInchToleranceInchPlus and MinusCut Lengths 0.030, 0.035, 0.045 0.001Cut Lengths 0.062, 0.094, 0.125 0.002Spools 0.020, 0.025 0.0005Spoo

28、ls 0.030, 0.035, 0.045 0.001Spools 0.062, 0.094 0.002TABLE 2B - SIZES AND DIAMETER TOLERANCES, SI UNITSFormNominal DiameterMillimetersToleranceMillimeterPlus and MinusCut Lengths 0.76, 0.089, 1.14 0.025Cut Lengths 1.57, 2.39, 3.18 0.05Spools 0.51, 0.64 0.013Spools 0.76, 0.89, 1.14 0.025Spools 1.57,

29、2.39 0.053.7.2 LengthCut lengths shall be furnished in 18, 27, or 36-inch (457, 686, or 914-mm) lengths, as ordered, and shall not vary more than +0, -0.5 inch (+0, -13 mm) from the length ordered.SAE AMS6468E Page 5 of 64. QUALITY ASSURANCE PROVISIONS4.1 Responsibility for InspectionThe vendor of w

30、ire shall supply all samples for vendors tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the wire conforms to specified requirements.4.2 Classification of Tests4.2

31、.1 Acceptance TestsComposition (3.1.1), alloy verification (5.2), sizes and tolerances (3.7) and, when specified, fracture toughness (3.5.3) are acceptance tests and shall be performed on each heat or lot as applicable.4.2.2 Periodic TestsDetermination of carbon, oxygen, nitrogen, and hydrogen on fi

32、nished wire (3.1.1.1), weldability (3.5.1), cast (3.5.2.1), and helix (3.5.2.2) are periodic tests and shall be performed at a frequency selected by the vendor unless frequency of testing is specified by purchaser.4.3 Sampling and TestingShall be in accordance with AMS2370.4.3.1 Specimens for fractu

33、re toughness testing shall be prepared from a single-vee-groove or double- vee-groove, butt joint weld made between two pieces of AMS6523 steel plate, 1.00 to 1.25 inches (25.4 to 31.8 mm) in thickness, which have been chamfered full depth to a 45-degree included angle if a single-vee-groove joint i

34、s used and to a 60-degree included angle if a double-vee-groove is used; the weld shall be perpendicular to the longitudinal grain direction of the test pieces. If a single-vee-grove joint is used, a backing bar 0.25 by 1.00 inch (6.4 by 25.4 mm) in cross section shall be used with a root gap of 0.2

35、5 inch (6.4 mm). The weld metal shall be in the direction of the specimen notch, in the center of the specimen, and shall be free from imperfections detrimental to properties of weld metal, determined by radiographic inspection in accordance with ASTM E 1032. The number and configuration of test spe

36、cimens for fracture toughness testing shall be as agreed upon by purchaser and vendor.4.4 ReportsThe vendor of wire shall furnish with each shipment a report showing the results of tests for chemical composition of each heat and stating that the wire conforms to the other technical requirements. Thi

37、s report shall include the purchase order number, heat and lot numbers, AMS6468E, nominal size, and quantity.4.5 Resampling and RetestingShall be in accordance with AMS2370.5. PREPARATION FOR DELIVERY5.1 Wire shall be supplied either on spools in one continuous length for machine welding or in cut l

38、engths for manual welding, as ordered. Wire on each spool or in each package of cut lengths shall be from the same heat of steel.5.2 Alloy VerificationWire from each spool or package of cut lengths shall be alloy verified by a method acceptable to purchaser. The alloy verification procedures of ARP4

39、926 are recommended.SAE AMS6468E Page 6 of 65.2.1 An 8-inch (203-mm) length of wire shall be made accessible at both ends of each spool for alloy verification.5.3 IdentificationShall be by tab marking in accordance with AMS2816 unless color coding in accordance with AMS2819 or another method is spec

40、ified by purchaser.5.4 Packaging and MarkingShall be by the premium quality method in accordance with AMS2814 unless the standard method in accordance with AMS2813 or another method is specified by purchaser.6. ACKNOWLEDGMENTA vendor shall include this specification number and its revision letter in

41、 all quotations and when acknowledging purchase orders.7. REJECTIONSWire not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection.8. NOTES8.1 A change bar (|) located in the left margin is for the convenience of the user in locating areas where

42、technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revision. Change bars and (R) are not used in original publications, nor in documents

43、that contain editorial changes only.8.2 Removal of wire from package may result in corrosion of the unprotected wire and variations of oxygen, nitrogen and hydrogen content.8.3 Terms used in AMS are clarified in ARP1917.8.4 Dimensions in inch/pound units are primary; dimensions in SI units are shown

44、 as the approximate equivalents of the primary units and are presented only for information.8.5 Purchase documents should specify not less than the following:AMS6468ESize and form (spools or cut lengths) of wire desiredLength of cut lengths or weight of spools desiredQuantity of wire desiredNumber and configuration of test specimens, method of test, and acceptance standards for fracture toughness testing when specified (See 3.5.3).PREPARED BY AMS COMMITTEE “E”