SAE AMS-DTL-23053 16A-2012 Insulation Sleeving Electrical Heat Shrinkable Crosslinked Elastomeric Polyolefin Flexible《柔性交联弹性体聚烯烃热收缩电气绝缘套管》.pdf

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2012 SAE International All rights reserved. No part of this publication m

3、ay be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside U

4、SA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMSDTL23053/16A AEROSPACE MATERIAL SPECIFICATION AMS-DTL-23053/16 REV. A Issued 1999-07 Revis

5、ed 2012-08 Superseding AMS-DTL-23053/16 Insulation Sleeving, Electrical, Heat Shrinkable, Crosslinked, Elastomeric Polyolefin, Flexible FSC 5970 RATIONALE Revise to include comments received by the government and industry, update references, align specification with SAE guidelines, and review specif

6、ication for known technical problems. The requirements for acquiring the sleeving described herein shall consist of this specification sheet and the issue of the following specification listed in that issue of the Department of Defense Index of Specifications and Standards (DODISS) specified in the

7、solicitation: MIL-DTL-23053. REQUIREMENTS Polymer type: The base elastomer used in formulating this sleeving shall be an elastomeric polyolefin. Continuous Operating temperature range: -103 F (-75 C) to +248 F (+120 C). Color: The sleeving shall be furnished in a black color that conforms to Class I

8、I of MIL-STD-104 (See 1.2.1). Longitudinal change: 10 percent SAE AMS-DTL-23053/16A Page 2 of 5 Military part number: The Military part number shall consist of the basic number of this specification sheet and dash numbers as follows: M23053/16 - X XX - X Example: Black, 1.000 inch (25.4 mm) as suppl

9、ied ID sleeving shall be identified as M23053/16-005-0. TABLE 1 - CONSTRUCTION DETAILS, INCHES (MM) 1/ Military part number 1/ As supplied ID minimum After unrestricted shrinkage ID maximum Wall Thickness 2/ M23053/16-001-0 0.250 (6.35) 0.125 (3.18) 0.035 (0.889) M23053/16-002-0 0.375 (9.53) 0.187 (

10、4.75) 0.040 (1.016) M23053/16-003-0 0.500 (12.70) 0.250 (6.35) 0.048 (1.220) M23053/16-004-0 0.750 (19.05) 0.375 (9.53) 0.057 (1.448) M23053/16-005-0 1.000 (25.40) 0.500 (12.70) 0.070 (1.778) M23053/16-006-0 1.500 (38.10) 0.750 (19.05) 0.095 (2.413) M23053/16-007-0 2.000 (50.80) 1.000 (25.40) 0.110

11、(2.794) M23053/16-008-0 3.000 (76.20) 1.500 (38.10) 0.125 (3.175) M23053/16-009-0 4.000 (101.60) 2.000 (50.80) 0.140 (3.556) 1/ Diameter limits for objects to be enclosed shall be as recommended in technical data. 2/ the color code identified is the standard acquisition color. Unrestricted shrinkage

12、 procedures: Test method 4.6.5; 347 F 4 (175 C 2) for 10 minutes. Color code designator (See 1.2.1) Size identifier (See Table 1) Class (Where no classes are specified in the specification sheet, the numeric “0” is used) Specification sheet SAE AMS-DTL-23053/16A Page 3 of 5 TABLE 2 - PHYSICAL PROPER

13、TIES 1/ Characteristic Requirement Test procedure and conditions As supplied: ID, minimum Table 1 4.6.3.1.1 Low temperature flexibility No cracks 4.6.7.1 -85 F 4 (-85 4F-65 C 2) Heat shock No cracks, flowing or dripping 4.6.8 392 F 4 (200 C 2) Restricted shrinkage No cracks 4.6.6 302 F 4 (150 C 2) V

14、oltage withstand Pass 4.6.6.3 After unrestricted shrinkage: ID, maximum Table 1 4.6.3.1.2 Wall thickness Table 1 4.6.3.2 Tensile strength, psi (MPa), minimum 1700 (11.7) 4.6.13 ASTM D 412 Ultimate elongation, percent, minimum 250 4.6.13 ASTM D 412 Tensile stress at 100 percent elongation, psi (MPa),

15、 maximum 1500 (10.4) 4.6.12.2 ASTM D 412 Dielectric strength, volts/mil (Kv/mm) minimum 300 (11.9) up to an “as supplied ID” of 0.500 200 (7.9) an “as supplied ID” of 0.500 and above 4.6.2 ASTM D 2671 Volume resistivity, 0hm-cm, minimum 1 x 1094.6.2 ASTM D 876 Specific gravity, maximum 1.5 4.6.2 AST

16、M D 792 Corrosion No corrosion or pitting 4.6.10.1 250 F 4 (121 C 2); 4.6.10.2 275 F 4 (135 C 2); for 16 hours Water absorption, percent, maximum 2.0 4.6.2 ASTM D 570, 24 hrs at 23C Heat resistance, properties after: 4.6.9 302 F 4 (150 C 2), 168 hours Tensile strength, psi (MPa), minimum 1500 (10.3)

17、 Ultimate elongation, percent, minimum 200 SAE AMS-DTL-23053/16A Page 4 of 5 TABLE 2 - PHYSICAL PROPERTIES 1/ (CONT.) Characteristic Requirement Test procedure and conditions Fluid resistance, properties after: 4.6.11 Tensile strength, psi (MPa), minimum 1500 (10.4) Ultimate elongation, percent, min

18、imum 200 Dielectric strength, volt/mil (Kv/mm), minimum 200 (7.9) Flammability Self-extinguishing within one minute and no more than 25 percent of indicator flag burned or charred 4.6.14 Procedure B ASTM 2671 Fungus resistance properties after: Tensile Strength, psi (MPa), minimum Ultimate elongatio

19、n, percent, minimum Dielectric strength, volts/mil (Kv/mm), minimum Rating less than 1 or 1700 (11.7) 250 300 (11.9) up to an “as supplied ID” of 0.500 200 (7.9) an “as supplied ID” of 0.500 and above 4.6.2 ASTM G 21 4.6.17 1/ Unless otherwise specified, requirements, test procedures and conditions

20、are for all classes. Storage life conditions: Supplier shall certify to storage at 65 to 95 F (18 to 35 C) for 2 years. Conformance to 3.5. See 3.5.2 for storage life extension. Intended use: Heat shrinkable flexible elastomeric sleeving is intended for use on heavy duty cables or harness systems, s

21、uch as ground support which see high levels of physical abuse and exposure to fuels and oils, coupled with high and low temperature extremes. NOTES A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have

22、been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. SAE AMS-DTL

23、-23053/16A Page 5 of 5 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary: dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. PREPARED BY AE-8D WIRE AND CABLE COMMITTEE