1、 SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2007 SAE International All rights reserved. No part of this publication m
3、ay be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA)
4、 Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ARP1947 REV. B AEROSPACE RECOMMENDED PRACTICE Issued 1985-10 Revised 2007-08 Superseding ARP1947A Dendrite Arm Spacing of Structural Aircraft Quality D357 Aluminum Alloy Castings, Determination and Acceptance of RATI
5、ONALE ARP1947B is a Five Year Review and update of this recommended practice. 1. SCOPE 1.1 This document covers the recommended practice for determining the acceptability of the dendrite arm spacing (DAS) of D357-T6 aluminum alloy castings required to have tensile strength not lower than 50,000 psi
6、345 MPa). 1.2 To apply this method, at least two coupons used for DAS measurement and tensile testing shall be attached to the casting in locations as defined by the cognizant engineering organization. 1.3 Areas of the casting which require DAS control must be accessible for surface DAS measurement
7、s. 1.4 Safety-Hazardous Materials While the materials, methods, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use. It is the sole responsibility of th
8、e user to ensure familiarity with the safe and proper use of any hazardous materials and to take necessary precautionary measures to ensure the health and safety of all personnel involved. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms
9、a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that do
10、cument shall apply. 2.1 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM B 557/B 557M Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products SAE ARP1947 Revision B - 2 -
11、 3. SUMMARY OF METHOD It has been shown that a linear correlation can be established between the ultimate tensile strength (UTS) and the spacing between the secondary dendrite arms of D357-T6 castings of high quality. The relationship, however, varies with the heat treatment process and chemical com
12、position of the alloy; therefore, a preliminary evaluation using attached coupons on the casting is necessary before actual DAS measurements on the casting are meaningful. By determining the UTS and DAS of attached coupons, the effect of composition and heat treatment on the DAS/UTS relationship is
13、determined. This relationship is used to evaluate the DAS measured in critical areas of the casting. 4. REFERENCE INFORMATION Information relative to this method may be found in Section 8. 5. DEFINITIONS 5.1 Dendrite arm spacing (DAS) refers to the spacing between the secondary arms of the dendrite
14、structure. 5.2 Particle intercepted distance (PID) refers to the spacing between the silicon particles that are intercepted by a straight line drawn in a random manner across the microstructure. 6. TEST PROCEDURE 6.1 Attached Coupon Testing 6.1.1 The average DAS and tensile strength of the attached
15、coupons shall be determined. The attached coupons shall exhibit a minimum difference of 0.0010 inch (0.025 mm) DAS and a UTS of 47,000 to 57,000 psi (324 to 393 MPa). 6.1.2 The DAS of the attached coupons may be determined on the untested grip or gauge length surface of the coupon as described in 6.
16、4 or by examining a metallographic specimen excised from the tensile specimen in any location not deformed by strain. 6.1.3 The UTS of the attached coupons shall be determined in accordance with ASTM B 557/B 557M. 6.2 Determination of Maximum DAS (DAS max) 6.2.1 Calculation Method: 6.2.1.1 The maxim
17、um acceptable DAS of the casting shall be determined using the following equation: 1213112maxDAS)UTSUTS()UTSUTS()DASDAS(DAS += (Eq. 1) where: DASmax= Maximum size DAS in 0.0001 inch (2.5 m) acceptable to meet minimum tensile properties DAS1= Size of DAS in 0.0001 inch (2.5 m) of coupon with smallest
18、 structure DAS2= Size of DAS in 0.0001 inch (2.5 m) of coupon with largest structure UTS1= Tensile strength of coupon with smallest DAS (ksi) UTS2= Tensile strength of coupon with largest DAS (ksi) UTS3= Minimum tensile strength required (ksi) SAE ARP1947 Revision B - 3 - 6.2.2 Graphic Method The ma
19、ximum DAS may be determined graphically in the following manner (see Figure 1). FIGURE 1 - MAXIMUM DAS DETERMINATION SAE ARP1947 Revision B - 4 - 6.2.2.1 Establish a graph using UTS units as the ordinate and DAS units as the abscissa. 6.2.2.2 Plot the UTS and DAS values from tests of the attached co
20、upons and draw a line connecting the two points. 6.2.2.3 The maximum DAS is determined by projecting the intersection of the 50 ksi (345 MPa) UTS and the related DAS value. 6.3 Casting Acceptance 6.3.1 The DAS shall be determined at each test location on the casting as defined by the cognizant engin
21、eering organization. 6.3.2 The DAS in all test locations shall be equal to or less than the maximum acceptable size determined in 6.2 6.4 Metallographic DAS Test Procedure 6.4.1 Prepolishing 6.4.1.1 Test locations shall be prepolished using 100 grit paper followed by 400 or 600 grit paper. 6.4.1.2 P
22、repolishing shall be sufficient to produce an outline of the secondary arm structure after etching. 6.4.1.3 Metal removal during polishing shall not exceed 0.005 inch (0.13 mm) thickness. 6.4.2 Final Polishing and Etching 6.4.2.1 Final polishing can be accomplished using mechanical or electro-polish
23、ing equipment. 6.4.2.2 The electro-polishing and electro-etching solution shall be made up as follows: TABLE 1 Distilled Water 120 mL Tartaric Acid 50 g Ethyl Alcohol 100 mL Butyl Cellosolve 100 mL Perchloric Acid (60%) 78 mL 6.4.2.3 Current density and times should be sufficient to reveal the dendr
24、ite structure of the material. 6.4.2.4 Chemical etching may be used by carefully swabbing the polished area with Kellers etch or other suitable etch to reveal the dendrite structure. Care must be exercised to not allow the etchant to spread to other areas of the casting. 6.4.2.5 After etching, the c
25、asting shall be cleaned to remove all etchant. 6.4.3 Microstructure Replication 6.4.3.1 The microstructure shall be transferred from the etched surface to a plastic replica for viewing by an optical microscope. 6.4.3.2 Each replica shall be identified for traceability to the test location of the cas
26、ting being evaluated. SAE ARP1947 Revision B - 5 - 6.4.3.3 A photograph at 100X magnification which clearly delineates the dendritic structure shall be obtained from the replica. 6.4.3.4 The microstructure shall clearly distinguish the secondary arm spacing from the casting surface. Improper polishi
27、ng, under-etching, or over-etching can produce a misleading microstructure. 6.4.3.5 If the microstructure is improperly polished, under-etched, or over-etched, the test location shall be repolished very lightly using 400 to 600 grit paper, repolished, and re-etched. Under-etched locations shall not
28、be re-etched without repolishing. 6.4.3.6 The test casting shall be rinsed in running water to remove the etching solution after the examination has been completed. 6.4.4 Photomicrograph 6.4.4.1 A photomicrograph shall be made at 100X magnification in the area which most clearly defines the general
29、microstructure. 6.4.4.2 Areas of the photomicrograph selected for DAS count shall be identified either directly on the original photomicrograph or on a copy of the photomicrograph. 6.4.5 Microstructure Evaluation 6.4.5.1 Either of the following methods for evaluation is acceptable; however, the meas
30、urement of clearly defined secondary dendrite arm spacing (DAS) is preferred. When this is not possible, the alternate procedure of measuring the distance between silicon particles located in a random manner along a single line shall be used. 6.4.5.2 All measurements used in the evaluation of a cast
31、ing for acceptability shall be made by the same method. 6.4.5.3 Preferred Measurement Method Extend a straight line across an area of well-defined structure such as illustrated in Figure 2. The line is drawn perpendicular to the growth direction of the secondary arms. The average distance between in
32、tercepts of silicon particles along the line shall be used to define the DAS of the structure. By measuring the total length of drawn line and counting the number of interceptions, the average DAS value can be determined in the following manner: ionMagnificat x onsIntercepti of Number(mm) Inch Line
33、Intercept of Length)mm(inch,DAS = (Eq. 2) SAE ARP1947 Revision B - 6 - FIGURE 2 - MEASUREMENT OF DAS TAKEN IN SELECTED AREAS 6.4.5.3.1 At least two areas of the microstructure shall be evaluated. The average of the two areas shall be considered to be the DAS of that test site. 6.4.5.4 Alternate Meas
34、urement Method This alternate procedure consists of drawing a straight line of known length across the microstructure and counting the number of times the line is intercepted by silicon particles (see Figure 3). The average distance between silicon particles is then used to quantify the structure. P
35、article intercept distance (PID) is determined by the following: ionMagnificat x Intercepts of Number(mm) Inch Line Intercept of Length(mm) inch PID, = (Eq. 3) SAE ARP1947 Revision B - 7 - FIGURE 3 - MEASUREMENT OF PID ACROSS STRUCTURE 6.4.5.5 At least two lines with a minimum length of 3 inches (76
36、 mm) shall be drawn which vary in their orientation to each other as much as practical. The average PID of the two lines shall be reported. 6.4.5.6 Caution should be used when using this procedure for measuring coarse dendritic structures. These structures may exhibit large amounts of interdendritic
37、 material which reduce the accuracy of the measurement. 6.4.5.7 In other sections of this recommended practice, PID may be interchanged with DAS without changing its technical intent. 7. TEST REPORTS 7.1 The test results shall be itemized as average values from each test site on the casting or integ
38、rally-attached coupon. 7.1.1 A photograph or copy of the photograph of the microstructure at each test site shall be furnished clearly delineating the lines drawn for microstructure measurements. 7.1.2 The test laboratory shall maintain on file, for not less than 90 days, the replica plate or tape u
39、sed in the evaluation. SAE ARP1947 Revision B - 8 - 8. REFERENCES Spear, R. E. and Gardner, G. R., “Dendrite Cell Size,“ Transactions of the American Foundrymens Society, Vol. 71, 1963, pp. 209-215. Bossing, E. N., and Hall, J. J., “Predicting Properties of Al-Si-Mg Casting with NDT,“ Foundry, Vol.
40、102, Oct. 1974, pp. 82-87. Oswalt, K. J. and Misra, M. S., “Dendritic Arm Spacings (DAS) - a Nondestructive Test to Evaluate Tensile Properties of Premium Quality Aluminum Alloy (Al-Si-Mg) Casting,“ AFS Transactions, 1980, pp. 845-862. Levy, S. A., Hughes, R. E., and Kemppinens, A. I., “Quantitative
41、 Metallography of As-Cast Aluminum Microstructures,“ AFS Cast Metals Research Journal, June 1969, pp. 93-96. Flemings, M. C., Uram, S. Z., and Taylor, H. F., “Solidification of Aluminum Casting,“ AFS Transactions, Vol. 68, 1960, pp. 670-684. Flemings, M. C., “Casting Metals,“ Science and Technology,
42、 Dec. 1968, pp. 13-24. 9. NOTES 9.1 The change bar ( l ) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document. PREPARED BY AMS COMMITTEE “D“
copyright@ 2008-2019 麦多课文库（www.mydoc123.com）网站版权所有
备案/许可证编号：苏ICP备17064731号-1