SAE AS 14101D-2010 BEARING PLAIN SELF-LUBRICATING SELF-ALIGNING LOW SPEED NARROW GROOVED RACE -65 TO +325 DEGREES F《平纹自润滑式自动对准低速精密带凹槽线种类轴承 -65至+325℉》.pdf

1、AEROSPACE STANDARD BEARING, PLAIN, SELF-LUBRICATING, SELF-ALIGNING, LOW SPEED, NARROW, GROOVED RACE, -65 TO +325 F AS14101Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, ele

2、ctronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1

3、998-07REVISED 2010-06THIRD ANGLE PROJECTION CUSTODIAN: AIRFRAME CONTROL BEARINGS GROUP REV.DFEDERAL SUPPLY CLASS 3120 AS14101SHEET 1 OF 3REV. DPROCUREMENT SPECIFICATION: AS81820SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineer

4、ing sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, re

5、vised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS14101DRATIONALE THE REASON FOR UPDATING THIS SPECIFICATION IS TO ADD THE ZINC NICKEL PLATING ONLY OPTION “ E ”

6、. THE PLATING OPTION “ P “ WILL REMAIN AS ZINC NICKEL OR CADMIUM PLATING. FIGURE 1 PART CONFIGURATION TABLE 1 - DIMENSIONS AND STRENGTHS PARTNO.* IB+.0000 .0005 ID* +.0000 .0005 H* .005 IMMIN P+.000.010Q (REF)W+.000.002IE+.000.008STATIC LIMIT LOADOSCIL- LATING LOADLBNO-LOADROTATIONAL BREAKAWAY TORQU

7、E IN-LB WT LBMAX(REF)RADIALLBAXIAL LB STANDARD *“K“ TYPE MS14101- 3 .1900 .5625 .218 .293 .025 10 .281 .500 3975 150 1500 0.25- 5.0 0-0.5 .020 MS14101- 4 .2500 .6562 .250 .364 .025 10 .343 .594 6040 430 3320 0.25- 5.0 0-0.5 .020 MS14101- 5 .3125 .7500 .281 .419 .035 10 .375 .650 8750 700 5460 0.25-

8、8.0 0-1.0 .030 MS14101-5A .3125 .7500 .281 .419 .035 10 .375 .660 8750 700 5460 0.25- 8.0 0-1.0 .030 MS14101- 6 .3750 .8125 .312 .475 .035 9 .406 .712 10 540 1100 6600 0.25- 8.0 0-1.0 .040 MS14101- 7 .4375 .9062 .343 .530 .035 8 .437 .806 13 200 1400 8050 0.25- 8.0 0-1.0 .050 MS14101- 8 .5000 1.0000

9、 .390 .600 .055 8 .500 .876 17 900 2100 10 400 0.25- 8.0 0-1.0 .070 MS14101- 9 .5625 1.0937 .437 .670 .055 8 .562 .970 23 200 3680 13 000 0.25- 8.0 0-1.0 .090 MS14101-10 .6250 1.1875 .500 .739 .055 8 .625 1.063 30 500 4720 16 450 0.25- 8.0 0-1.0 .120 MS14101-12 .7500 1.4375 .593 .920 .055 8 .750 1.3

10、13 46 400 6750 23 600 0.25- 8.0 0-1.0 .210 MS14101-14 .8750 1.5625 .703 .980 .055 8 .875 1.438 62 200 9350 30 250 0.25-12.0 0-2.0 .270 MS14101-16 1.0000 1.7500 .797 1.118 .055 9 1.000 1.626 82 200 12 160 38 000 0.25-12.0 0-2.0 .390 * SEE REQUIREMENT 5 “NO-LOAD TORQUE“ AND NOTE 8. * SEE NOTE 7. * FOR

11、 TYPE A BEARINGS, THE CORRESPONDING P/N WILL HAVE AN “A” DESIGNATION AFTER THE MS P/N (E.G., MS14101A-3). *V-GROOVE INNER ANGLE FOR MS14101-5A WAS REVISED FROM 20 DEGREES MIN TO 30 DEGREES MIN TO IMPROVE SWAGE TOOL ACCESS ON REV C. MS14101-5A PARTS MANUFACTURED PRIOR TO REV C MAY BE USED UNTIL EXIST

12、ING STOCK IS DEPLETED.MS14101-5 INACTIVE FOR NEW DESIGN AEROSPACE STANDARD AS14101SHEET 2 OF 3REV. DBEARING, PLAIN, SELF-LUBRICATING, SELF-ALIGNING, LOW SPEED, NARROW, GROOVED RACE, -65 TO +325 F TABLE 2 - OVERSIZE BEARING DIMENSIONS 1/ 2/RESTRICTED USAGE FOR REPAIR WORK ONLY .010 INCH AND .020 INCH

13、 OVERSIZE OUTSIDE DIAMETER FOR REPLACEMENT OF BEARINGS SHOWN ON SHEET 1 PARTNO. 3/NOMINAL SIZE1STOVERSIZE (.010) IDPARTNO. 3/NOMINAL SIZE2NDOVERSIZE (.020) IDMS14101- 3T .1875 .5725 MS14101- 3U .1875 .5825 MS14101- 4T .2500 .6662 MS14101- 4U .2500 .6762 MS14101- 5AT .3125 .7600 MS14101- 5AU .3125 .7

14、700 MS14101- 6T .3750 .8225 MS14101- 6U .3750 .8325 MS14101- 7T .4375 .9162 MS14101- 7U .4375 .9262 MS14101- 8T .5000 1.0100 MS14101- 8U .5000 1.0200 MS14101- 9T .5625 1.1037 MS14101- 9U .5625 1.1137 MS14101-10T .6250 1.1975 MS14101-10U .6250 1.2075 MS14101-12T .7500 1.4475 MS14101-12U .7500 1.4575

15、MS14101-14T .8750 1.5725 MS14101-14U .8750 1.5825 MS14101-16T 1.0000 1.7600 MS14101-16U 1.0000 1.77001/ BEFORE INITIATING A REPAIR PROCEDURE TO USE AN OVERSIZE BEARING, APPROVAL FOR MODIFYING AND REIDENTIFYING THE BEARING HOUSING MUST BE OBTAINED FROM THE COGNIZANT ENGINEERING AUTHORITY. 2/ REFER TO

16、 NAS0331 FOR INSTALLATION PROCEDURE AND STAKING FORCES. 3/ FOR TYPE A BEARINGS, THE CORRESPONDING PART NUMBER WILL HAVE AN “A” DESIGNATION AFTER THE MS PART NUMBER (E.G., MS14101A-3). REQUIREMENTS: 1. MATERIAL: BALL, 440C (AMS5630, AMS5880, OR AMS5618) OR PH13-8Mo AMS5629 H1000 (SEE NOTE 8 FOR P/N E

17、XAMPLE AND DESIGNATION). RACE, 17-4PH (AMS5643). LINER, PTFE SHALL BE INCLUDED IN THE LINER. 2. SURFACE TEXTURE: BALL DIA Ra 8 MAX; BALL FACES, BALL BORE AND RACE DIA Ra 32 MAX; ALL OTHER METALLIC SURFACES Ra 125 MAX. LINER SURFACES ARE EXEMPT FROM SURFACE TEXTURE MEASUREMENTS. 3. HARDNESS: BALL, 44

18、0C HRC 55-62 OR PH13-8Mo HRC 43 MIN; RACE; HRC 28 MIN/HRC 37 MAX BEFORE SWAGING. 4. SURFACE FINISH: RACE: PLATING, WHEN SPECIFIED, SHALL BE ZINC-NICKEL PLATING PER AMS2417, TYPE 2, OR CADMIUM PLATING PER AMS-QQ-P-416, TYPE II, CLASS 2, WITH A THICKNESS RANGE OF 0.0003 TO 0.0006 INCHES. PLATE ON THE

19、OUTSIDE DIAMETER SURFACE AND ON THE FLAT BETWEEN THE OUTSIDE DIAMETER AND THE GROOVE. PLATING RUNOUT MAY OCCUR EITHER IN THE GROOVE OR IN THE AREA BETWEEN THE GROOVE AND THE BALL. SEE NOTE 8 FOR P/N EXAMPLE AND DESIGNATION. BALL: PH13-8Mo, PASSIVATE PER AMS2700 OR ASTM A 967; 440C, PASSIVATE PER AMS

20、2700 OR ASTM A 967, OPTIONAL. CHROME PLATING PER AMS2460 IS ALLOWED. BALL SHALL BE CHROME PLATED IF QUALIFIED WITH IT. 5. NO-LOAD TORQUE: WHEN THE LETTER “K” IS PRESENT IN THE PART NUMBER, LOWER VALUES OF NO-LOAD TORQUE ARE SPECIFIED PER TABLE 1. IF THE MEASURED TORQUE OF A “K” TYPE BEARING IS LESS

21、THAN 0.1 INCH-POUND, THE INTERNAL RADIAL PLAY SHALL BE MEASURED AND SHALL NOT EXCEED THE FOLLOWING: DASH NO. MAXIMUM RADIAL PLAY MAXIMUM AXIAL PLAY -3K THRU -12K 0.0007 INCH 0.0028 INCH -14K THRU -16K 0.0010 INCH 0.0040 INCH THE INTERNAL AXIAL PLAY SHALL BE MEASURED FOR ALL “K“ TYPE BEARINGS. AEROSP

22、ACE STANDARD AS14101SHEET 3 OF 3REV. DBEARING, PLAIN, SELF-LUBRICATING, SELF-ALIGNING, LOW SPEED, NARROW, GROOVED RACE, -65 TO +325 F NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1.

23、DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE; DECIMALS .010 AND ANGLES 0.5 DEGREES. 2. BREAK SHARP EDGES AND CORNERS AND REMOVE ALL BURRS AND SLIVERS. 3. THE -3 SIZE BEARING IS EXEMPT FROM THE “RADIAL STATIC LIMIT LOAD“ TEST BECAUSE THE LOAD CAPACITY OF THE BEARING IS PIN CRI

24、TICAL. 4. WHEN TESTED TO THE FLUID CONTAMINATION AND SUB-ZERO TEMPERATURE REQUIREMENTS OF THE PROCUREMENT SPECIFICATION, THE OSCILLATING LOAD SHALL BE DECREASED TO 75% OF THE SPECIFIED LOAD. 5. WHEN FLUIDS AND ELEVATED TEMPERATURES (ABOVE 200 F) ARE BOTH PRESENT IN AN APPLICATION, THEN REDUCTIONS IN

25、 OPERATING LOADS OR BEARING LIFE MAY BE REQUIRED. 6. DASH NUMBER DESIGNATES NOMINAL BORE DIA IN SIXTEENTHS OF AN INCH. 7. DIMENSION “D” TO BE MET AFTER PLATING. DIMENSION “H“ TO BE MET BEFORE PLATING WHEN APPLICABLE. 8. EXAMPLE OF PART NO. MS14101 A -6 C P K T = .375 NOMINAL BORE DIA, PH13-8MO BALL

26、MATERIAL, ZINC-NICKEL PLATED, LOW TORQUE, .010 INCH OVERSIZE O.D. (DIMENSION D). ABSENCE OF THE LETTERS “ T “ AND “ U “ INDICATE STANDARD OUTER DIAMETER ( D), (SEE TABLE 1). T = .010” OVERSIZE D (FOR REPAIR ONLY, SEE TABLE 2). U = .020” OVERSIZE D (FOR REPAIR ONLY, SEE TABLE 2). ABSENCE OF THE LETTE

27、R “ K “ INDICATES STANDARD BREAKAWAY TORQUE (SEE TABLE 1). LETTER “ K “ INDICATES LOW BREAKAWAY TORQUE (SEE TABLE 1). ABSENCE OF THE LETTER “ P “ INDICATES NO PLATING. LETTER “ P “ INDICATES ZINC-NICKEL OR CADMIUM PLATING (SEE REQUIREMENT 4). LETTER “ E “ INDICATES ZINC-NICKEL PLATING ONLY (SEE REQU

28、IREMENT 4). ABSENCE OF LETTER “ C “ INDICATES 440C BALL MATERIAL LETTER “ C “ INDICATES PH13-8Mo BALL MATERIAL SIZE BORE DIAMETER (DASH NO. FROM TABLE 1). ABSENCE OF THE LETTER “ A “ INDICATES TESTED TO 25,000 CYCLES LETTER “ A “ INDICATES TESTED TO 100,000 CYCLES BASIC PART NUMBER. 9. IN THE EVENT

29、OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE. 10. REFERENCED GOVERNMENT (OR NON-GOVERNMENT) DOCUMENTS OF THE ISSUE LISTED IN THAT ISSUE OF THE DEPARTMENT OF DEFENSE INDEX OF SPECIFICATIONS AND STANDARDS DODISS SPECIF

30、IED IN THE SOLICITATION FORM A PART OF THIS STANDARD TO THE EXTENT SPECIFIED HEREIN. 11. A CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.