SAE AS 14237A-2003 BUSHING SLEEVE PLAIN PRESS FIT REAM TYPE《扩口型压配滑动套筒衬套》.pdf

1、AEROSPACE STANDARD BUSHING, SLEEVE PLAIN, PRESS FIT, REAM TYPE AS14237 ISSUED 1997-08REVISED 2003-11REAFFIRMED 2010-06CUSTODIAN: SAE ACBG REV.AFEDERAL SUPPLY CLASS3120 AS14237SHEET 1 OF 4REV.ANOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY STANDARD, MS14237, AND CONTAINS ONLY MINOR E

2、DITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE ORIGINAL MILITARY STANDARD WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001) PERTAINING TO A

3、CCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR STANDARD FORMAT, AND

4、 (C) THE EXCLUSION OF ANY QUALIFIED PRODUCT LIST (QPL) SECTIONS.UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTE

5、D BY SAE AND IS NOT PART OF THIS SAE TECHNICAL DOCUMENT. THIS DOCUMENT INCLUDES CADMIUM AS A PLATING MATERIAL. THE USE OF CADMIUM HAS BEEN RESTRICTED AND/OR BANNED FOR USE IN MANY COUNTRIES DUE TO ENVIRONMENTAL AND HEALTH CONCERNS. THE USER SHOULD CONSULT WITH LOCAL OFFICIALS ON APPLICABLE HEALTH AN

6、D ENVIRONMENTAL REGULATIONS REGARDING ITS USE. SAE Technical Standards Board Rules providethat: “This report is published by SAE to advancethe state oftechnical and engineering sciences.Theuse ofthis reportisentirelyvoluntary, andits applicability and suitability for any particularuse,including any

7、patentinfringement arising therefrom,isthe sole responsibility of the user.”SAE reviews each technical reportatleastevery five years atwhich timeitmay bereaffirmed,revised, or cancelled.SAE invites your written comments and suggestions.Copyright 2010All rights reserved. No part of this publication m

8、ay be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA)

9、 Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE International SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS14237AAEROSPACE STANDARD BUSHING, SLEEVE PLAIN, PRESS FIT, REAM TYPE AS14237

10、REV.AAS14237SHEET 2 OF 4REV.AFIGURE 1 TABLE 1 SIZE DASH NO.NOM.DIA. A BRECMDHOUSING BORE INTERFERENCE FIT(REF.)WEIGHT (REF.) (LBS.)-03 .1900 .177 .184 .3142 .3137 .3133 .3125 .0017.0004.053 X L(MAX)X D -04 .2500 .235 .243 .3767 .3762 .3758 .3750 .0017.0004.069 X L(MAX)X D -05 .3125 .299 .307 .4393 .

11、4388 .4383 .4375 .0018.0005.082 X L(MAX)X D -06 .3750 .356 .364 .5020 .5013 .5008 .5000 .0020.0005.099 X L(MAX)X D -07 .4375 .421 .428 .5646 .5639 .5634 .5625 .0021.0005.112 X L(MAX)X D -08 .5000 .483 .490 .6272 .6264 .6259 .6250 .0022.0006.126 X L(MAX)X D -10 .6250 .608 .615 .8150 .8140 .8134 .8125

12、 .0025.0006.232 X L(MAX)X D -12 .7500 .732 .742 .9400 .9390 .9384 .9375 .0025.0006.274 X L(MAX)X D -14 .8750 .857 .867 1.06511.06411.06351.0625.0026.0006.315 X L(MAX)X D -16 1.0000 .982 .992 1.19011.18911.18851.1875.0026.0006.356 X L(MAX)X D -18 1.1250 1.1071.1171.31511.31411.31351.3125.0026.0006.39

13、6 X L(MAX)X D -20 1.2500 1.2321.2421.44011.43911.43851.4375.0026.0006.437 X L(MAX)X D AEROSPACE STANDARD BUSHING, SLEEVE PLAIN, PRESS FIT, REAM TYPE AS14237 REV.AAS14237SHEET 3 OF 4REV.AWEIGHT(MAX)= /4 x (O.D.(MAX)2- (I.D.(MIN)2x L(MAX)x D TABLE 2 MATERIALDENSITY (REF)4130 STEEL .28317-4 PH .283ALUM

14、INUM NICKEL BRONZE .276 BERYLLIUM COPPER .298MATERIAL: ALLOY STEEL: 4130 STEEL PER AMS-S-6758 OR AMS-T-6736 CORROSION RESISTANT STEEL: 17-4 PH PER AMS 5643, PASSIVATE PER AMS-QQ-P-35 OR ASTM A 967 CITRIC 1, CITRIC 2 OR CITRIC 3 ALUMINUM NICKEL BRONZE PER AMS 4640 BERYLLIUM COPPER PER AMS 4534 OR AST

15、M B 196, CONDITION TH04 HEAT TREAT: ALLOY STEEL: 125,000 - 145,000 PSI UTS CORROSION RESISTANT STEEL: 135,000 - 170,000 PSI UTS BERYLLIUM COPPER: 165,000 PSI UTS (MINIMUM) FINISH: (P): CADMIUM PLATE OUTSIDE DIAMETER AND END SURFACES PER AMS-QQ-P-416 TYPE II, CLASS 2. FLASH PERMITTED IN BORE. (E): ZI

16、NC NICKEL PLATE ALL OVER (I.D. OPTIONAL) PER AMS 2417 TYPE 2. (D): IVD ALUMINUM COATING PER MIL-C-83488 TYPE II, CLASS 3. PART MARKING: BAG AND TAG WITH THE SUPPLIERS NAME, TRADEMARK, OR CODE NUMBER, BASIC PART NUMBER (LESS MS PREFIX). MATERIAL CODE AND SIZE CODE. PACKAGES SHALL BE MARKED WITH THE S

17、UPPLIERS NAME, TRADEMARK OR CODE NUMBER AND THE COMPLETE PART NUMBER FOR ALL BUSHING SIZES. PART CALLOUT:EXAMPLES: MS14237C06P037 = BUSHING, PLAIN, CORROSION RESISTANT STEEL, FOR .375 NOM. DIA., CADMIUM PLATED, .370 INCHES LONG MS14237B16-500 = BUSHING, PLAIN, BERYLLIUM COPPER, FOR 1.000 NOM. DIA.,

18、UNPLATED, 5.00 INCHES LONG IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE. AEROSPACE STANDARD BUSHING, SLEEVE PLAIN, PRESS FIT, REAM TYPE AS14237 REV.AAS14237SHEET 4 OF 4REV.ANOTES: 1. LENGTH TO BE SPECIFI

19、ED IN .010 INCH INCREMENTS. BUSHING LENGTHS ALLOWED TO BE CODED BY THIS STANDARD SHALL BE A MAXIMUM OF 5 TIMES THE NOMINAL BORE DIAMETER AND A MINIMUM OF 1/4 TIMES THE NOMINAL BORE DIAMETER. 2. DIAMETERS TO BE CONCENTRIC WITHIN .003 FIR. 3. DIMENSIONS TO BE MET AFTER PLATING. 4. ALL SURFACES 125 RA OR SMOOTHER IN ACCORDANCE WITH ASME B46.1. 5. THESE BUSHINGS INTENDED FOR REAMING ON ASSEMBLY. 6. DIMENSIONS ARE IN INCHES.