SAE AS 151701 THRU AS152000C-2015 STUD STEPPED 1 5 DIA ENGAGEMENT CADMIUM PLATED STEEL UNS G87400 5000-13 UNS X 4375-20 UNF-3A.pdf

1、 AEROSPACE STANDARD STUD, STEPPED, 1.5 DIA ENGAGEMENT, CADMIUM PLATED, STEEL UNS G87400, .5000-13 UNS X .4375-20 UNF-3A AS151701AS152000Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by

2、any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sa

3、e.org ISSUED1998-11REVISED2015-09THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.CFEDERAL SUPPLY CLASS 5307 AS151701 AS152000 SHEET 1 OF 2 REV. C PROCUREMENT SPECIFICATION: AS7456 SAETechnicalStandardsBoard Rulesprovidethat:“Thisreportispublished bySAEto advance the state oftechnicaland engineering scien

4、ces.The use ofthisreportisentirely voluntary,anditsapplicabilityandsuitabilityforanyparticularuse,includinganypatentinfringementarising therefrom,is the sole responsibilityoftheuser.”SAEreviewseachtechnicalreportatleasteveryfiveyearsatwhich time itmaybe revised,reaffirmed,stabilized,orcancelled.SAEi

5、nvitesyourwritten commentsandsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS151701C RATIONALE THIS LIMITED SCOPE BALLOT CORRECTS A DUPLICATE PART NUMBER IN TABLE 1 TO AGREE WITH ORIGINAL PUBLICATION AN151701 THRU

6、AN152000. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD AN151701 THRU AN152000 REVISION 4. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. 63.409.399BL R.062.031APPROX45.4375 - 20 UNF - 3AMIL - S -

7、 7742 C .5000 - 13 UNS MIL- S - 7742SEE TABLE FOR PITCH XYE11UNDERSIZE AND OVERSIZEIDENTIFICATION STAMP MATERIAL IDENTIFICATIONSTAMP TO AMS2800 .090.150.090.150ENLARGED VIEW Y ENLARGED VIEW X32SECTION THRU BOTHTHREAD PROFILES.052 x 45 APPROX.072.037 x 45 APPROX.057.740THREAD RUNOUTPER AS3062 TO AMS2

8、800 SEE TABLE 1A .006 AMIN FULL THREADMIN FULL THREAD.010 MAX DEPTH.010 MAX DEPTH.760+FIGURE 1 - STUD AEROSPACE STANDARD AS151701 AS152000 SHEET 2 OF 2 REV. C STUD, STEPPED, 1.5 DIA ENGAGEMENT, CADMIUM PLATED, STEEL UNS G87400, .5000-13 UNS X .4375-20 UNF-3A TABLE 1 - PART NUMBERS AND DIMENSIONS UND

9、ERSIZE AND OVERSIZE IDENTIFICATION -.003 STANDARD +.003 +.006 +.009 +.012 -336912C PD BEFORE PLATING PD AFTER PLATING PD LEAD THREAD .495- .500 .495- .500 .495- .500 .495- .500 .504- .509 .504- .509 .4518-.4528 .4548-.4558 .4578-.4588 .4608-.4618 .4638-.4648 .4668-.4678 .4523-.4538 .4553-.4568 .4583

10、-.4598 .4613-.4628 .4643-.4658 .4673-4688 .4450-.4470 .4480-.4500 .4510-.4530 .4540-.4560 .4570-.4590 .4600-.4620 L B PART NUMBER PART NUMBER PART NUMBER PART NUMBER PART NUMBER PART NUMBER 1.500 .625 AN151719 AN151720 AN151721 AN151722 AN151723 AN151724 1.562 .688 AN151725 AN151726 AN151727 AN15172

11、8 AN151729 AN151730 1.625 .750 AN151731 AN151732 AN151733 AN151734 AN151735 AN151736 1.688 .750 AN151737 AN151738 AN151739 AN151740 AN151741 AN151742 1.938 .938 AN151743 AN151744 AN151745 AN151746 AN151747 AN151748 NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MAT

12、ERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. MATERIAL: STEEL AMS6322 (UNS G87400). 2. PROCUREMENT SPECIFICATION: AS7456. 3. FINISH: CADMIUM PLATE PER AMS2400. DIMENSIONS ARE AFTER PLATING, EXCEPT WHERE SHOWN. 4. MAGNETIC PARTICLE INSPECTION PER ASTM E1444 AFTER PL

13、ATING. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 8. DIMENSIONS ARE I

14、N INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010. 9. DO NOT USE UNASSIGNED PART NUMBERS. 10. REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE T

15、O THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.