SAE AS 16721-2013 INSERT ARRANGEMENTS AS81582 CONNECTORS UMBILICAL《中央AS81582连接器的插入安排》.pdf

1、AEROSPACE STANDARD INSERT ARRANGEMENTS, AS81582 CONNECTORS, UMBILICAL AS16721Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording,

2、 or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2013-09THIRD ANGLE PROJECTION CUSTODIAN: AE-8/

3、AE-8C1 FEDERAL SUPPLY CLASS 5935 AS16721SHEET 1 OF 2PROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability

4、 forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values you

5、r input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS16721RATIONALE AS16721 PERMITS THE CANCELLATION AND SUPERSESSION OF MIL-STD-1672 WITH THIS DOCUMENT. TOLERANCES HAVE BEEN ADDED FOR THE CONTACT/CAVITY LOCATIONS TO ALIGN WITH SIMILAR INSERT DOC

6、UMENTS. FIGURE 1 - INSERT CONFIGURATION AEROSPACE STANDARD AS16721SHEET 2 OF 2INSERT ARRANGEMENTS, AS81582 CONNECTORS, UMBILICAL TABLE 1 - CONTACT LOCATION AND DIMENSIONS CONTACT LOCATION CONTACT NUMBER LOCATION CONTACT NUMBER LOCATION CONTACT NUMBER LOCATION X AXIS Y AXIS X AXIS Y AXIS X AXIS Y AXI

7、S 1 .000 .000 15 .000 -.222 29 -.336 -.240 2 -.111 +.105 16 +.124 -.262 30 -.245 -.3333 -.156 -.018 17 +.222 -.176 31 -.129 -.392 4 -.096 -.134 18 +.280 -.059 32 .000 -.4135 +.096 -.134 19 +.275 +.071 33 +.129 -.392 6 +.156 -.018 20 +.214 +.186 34 +.245 -.3337 +.111 +.105 21 +.111 +.265 35 +.336 -.2

8、40 8 +.000 +.172 22 .000 +.335 36 +.394 -.1239 -.111 +.265 23 -.116 +.395 37 +.412 +.006 10 -.214 +.186 24 -.234 +.339 38 +.389 +.134 11 -.275 +.071 25 -.328 +.249 39 +.328 +.249 12 -.280 -.059 26 -.389 +.134 40 +.234 +.339 13 -.222 -.176 27 -.412 +.006 41 +.116 +.395 14 -.124 -.262 28 -.394 -.123 R

9、EQUIREMENTS: 1. z INDICATES CENTERLINE OF INSERT ARRANGEMENT AND MASTER KEY OR KEYWAY OF CONNECTOR SHELL. NORMAL POSITION SHOWN. ALL DIMENSIONS (TP) ARE IN INCHES AND ARE TRUE POSITIONAL. 2. MARKINGS SHOWN ARE FOR SOCKET INSERT FRONT FACE AND PIN GROMMET. PIN INSERT AND SOCKET GROMMET ARE THE OPPOSI

10、TE. 3. FOR DATUM A, REFER TO THE APPLICABLE SPECIFICATION SHEETS. 4. DIMENSIONING AND TOLERANCING IN ACCORDANCE WITH ANSI/ASME Y14.5. 5. UNLESS OTHERWISE INDICATED, DIMENSIONS ARE SYMMETRICAL ABOUT CENTERLINES OF THE INSERT AND SHELL. TABLE 2 - INSERT ARRANGEMENT DETAILS ARRANGEMENT NUMBER NUMBER OF

11、 CONTACTS SIZE CONTACTS SERVICE RATING CONTACT LOCATION SHELL SIZE -3 41 20 I SEE TABLE 22 6. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.