SAE AS 1895 15E-2010 Flange End Female Type II Low Profile Design Standard《低剖面II型阴性法兰端设计标准》.pdf

1、AEROSPACE STANDARD (R) FLANGE END, FEMALE, TYPE II LOW PROFILE DESIGN STANDARD AS1895/15Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying,

2、 recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1985-12REVISED 2010-06THIRD ANGLE P

3、ROJECTION CUSTODIAN: G-3/G-3A REV.EFEDERAL SUPPLY CLASS 5340 AS1895/15SHEET 1 OF 3REV. EPROCUREMENT SPECIFICATION: /1/ NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely volunta

4、ry, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments an

5、dsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS1895/15ERATIONALE DELETE MATERIAL, FINISH, NON-DESTRUCTIVE EVALUATION LIMITS, AND QUALIFICATION REQUIREMENTS FROM THE DESIGN STANDARD THAT ARE REQUIREMENTS PROPERLY

6、SPECIFIED ON THE PARTS STANDARDS. REINSTATE DIMENSIONS INADVERTENTLY REMOVED DURING REAFFIRMATION. 32CD AVGE AVGC AVGA AVGMGAUGE.085.081TOL LAUNLESS OTHERWISESPECIFIED A TOBE STRAIGHT WITHINTHIS LIMIT/4/.0723 r .0020/3/2063.62 MIN.042.032R.004 A.025.015R.020.0052X X 45r 5.080.070RTOL KTOL KTOL KTOL

7、KFIGURE 1 - FLANGE END DESIGN Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS1895/15SHEET 2 OF 3REV. E(R) FLANGE END, FEMALE, TYPE II LOW PROFILE DESIGN STANDARD TABLE 1 - DIMEN

8、SIONS DESIGN STANDARD NUMBER /11/(NOMINAL TUBE SIZE)A+.000-.005 C+.005-.000 /4/D.005 E+.005-.000 K L M AS1895/15-100 1.00 1.069 .900 1.510 1.386 .001 .003 1.360 AS1895/15-125 1.25 1.319 1.150 1.760 1.636 .001 .003 1.610 AS1895/15-150 1.50 1.569 1.400 2.010 1.886 .002 .003 1.860 AS1895/15-175 1.75 1.

9、819 1.650 2.260 2.136 .002 .003 2.110 AS1895/15-200 2.00 2.069 1.900 2.510 2.386 .002 .003 2.360 AS1895/15-225 2.25 2.319 2.150 2.760 2.636 .002 .003 2.610 AS1895/15-250 2.50 2.569 2.400 3.010 2.886 .003 .003 2.860 AS1895/15-275 2.75 2.819 2.650 3.260 3.136 .003 .003 3.110 AS1895/15-300 3.00 3.069 2

10、.900 3.510 3.386 .003 .003 3.360 AS1895/15-325 3.25 3.319 3.150 3.760 3.636 .003 .003 3.610 AS1895/15-350 3.50 3.569 3.400 4.010 3.886 .004 .003 3.860 AS1895/15-400 4.00 4.069 3.900 4.510 4.386 .004 .004 4.360 AS1895/15-450 4.50 4.569 4.400 5.010 4.886 .005 .004 4.860 AS1895/15-500 5.00 5.069 4.900

11、5.510 5.386 .005 .004 5.360 AS1895/15-550 5.50 5.569 5.400 6.010 5.886 .006 .004 5.860 AS1895/15-600 6.00 6.069 5.900 6.510 6.386 .006 .004 6.360 AS1895/15-650 6.50 6.569 6.400 7.010 6.886 .007 .004 6.860 AS1895/15-700 7.00 7.069 6.900 7.510 7.386 .007 .004 7.360 AS1895/15-750 7.50 7.569 7.400 8.010

12、 7.886 .008 .004 7.860 NOTES: /1/ THIS FLANGE END IS DESIGNED TO MATE WITH FLANGE END PER AS1895/14 AND FOR USE WITH FLANGES PER AS1895. 2. MAXIMUM VARIATION OF WALL (RADIAL) THICKNESS IN ANY DIAMETRAL PLANE TO BE WITHIN .004 TOTAL. /3/ WORKMANSHIP: THE FLANGE END SHALL BE FREE OF SHARP EDGES AND BU

13、RRS AND SHALL BE CAPABLE OF MATING UNDER ALL TOLERANCE CONDITIONS OF THE COMPONENT PARTS. SEALING SURFACE SHALL BE FREE OF SCRATCHES AND SURFACE FINISH SHALL BE CIRCULAR AND CONCENTRIC TO BORE DIAMETER. /4/ THIS DIAMETER MAY BE REDUCED IN ORDER TO DECREASE OUT-OF-ROUND DEFORMATION OF FLANGE ENDS PRO

14、DUCED BY COUPLING LOADING, IF DESIRED, OR TO COMPENSATE FOR CASTING FACTORS. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra OR FINER. 6. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONING AND

15、TOLERANCING: ANSI Y14.5M-1982. 8. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .XXX = .010, .XX = .03, ANGULAR DIMENSIONS 0 DEGREES 30. 9. THIS IS A DESIGN STANDARD. DO NOT USE AS A PART NUMBER. 10. A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE

16、 OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORI

17、GINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS1895/15SHEET 3 OF 3REV. E(R) FLANGE END, FEMALE, TYPE II

18、 LOW PROFILE DESIGN STANDARD /11/ EXAMPLE OF DRAWING CALLOUT: a. TABULATED PART DRAWING: FLANGE END PER AS1895/15. b. INDIVIDUAL PART DRAWING: BASIC NUMBER FLANGE END SIZE (2.00 in)AS1895/15 - 200Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-