SAE AS 21911C-2008 TEE BULKHEAD FLARELESS TUBE INTERNAL THREAD ON RUN《使用内螺纹闷头三通非扩口管》.pdf

1、AEROSPACE STANDARD TEE, BULKHEAD, FLARELESS TUBE, INTERNAL THREAD ON RUN AS21911CCopyright 2008 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, record

2、ing, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1998-03REAFFIRMED 2007-07 REVISED 2008-06 THI

3、RD ANGLE PROJECTION CUSTODIAN: SAE G-3/G-3B FEDERAL SUPPLY CLASS 4730 AS21911C SHEET 1 OF 4PROCUREMENT SPECIFICATION: /10/ AS18280SAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andengineering sciences.The use of thisreport is entirel

4、y voluntary, andits applicabilityandsuitability forany particularuse, including any patent infringement arising therefrom, is thesole responsibility oftheuser.” SAE reviews each technical report at least every five yearsat which time it may be reaffirmed, revised, orcancelled. SAE invites yourwritte

5、n commentsandsuggestions. RATIONALE1. NOTE 10: NEW WORDING FOR PROCUREMENT NOTE. 2. WARNING NOTE ADDED FOR RESTRICTED MATERIAL. 3. THE 5 IN NOTE 5 AND TABLE 1 IS CHANGED TO /5/. 4. ERROR CORRECTIONS. FIGURE 1 - TEE, BULKHEAD, FLARELESS TUBE, INTERNAL THREAD ON RUN Copyright SAE International Provide

6、d by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD TEE, BULKHEAD, FLARELESS TUBE, INTERNAL THREAD ON RUN AS21911C SHEET 2 OF 4TABLE 1A - DIMENSIONS B-U DASHNO./5/NOMINALTUBESIZET THREAD AS8879BMINJ+.047-.000K+.047-.000

7、Q+.047-.000R+.047-.000URAD-2 .125 .3125-24 UNJF-3A .375 .719 .625 .844 1.375 .063 -3 .188 .3750-24 UNJF-3A .406 .813 .688 .906 1.453 .094 -4 .250 .4375-20 UNJF-3A .438 .906 .750 1.094 1.672 .094 -5 .313 .5000-20 UNJF-3A .438 .938 .750 1.094 1.672 .094 -6 .375 .5625-18 UNJF-3A .469 1.031 .813 1.156 1

8、.891 .125 -8 .500 .7500-16 UNJF-3A .562 1.250 1.000 1.344 2.031 .125 -10 .625 .8750-14 UNJF-3A .625 1.469 1.156 1.500 2.250 .125 -12 .750 1.0625-12 UNJ-3A .688 1.750 1.344 1.641 2.438 .125 -16 1.000 1.3125-12 UNJ-3A .688 2.063 1.531 1.844 2.656 .125 -20 1.250 1.6250-12 UNJ-3A .688 2.313 1.719 1.984

9、2.797 .125 TABLE 1B - DIMENSIONS V-Z WEIGHT, LB/EA, APPROX, REF. DASHNO./5/ VWAPPROX XAPPROX Y+.047-.000ZDIA STEELALALLOY TIALLOY -2 .500 .469 .313 .844 .563 .051 .018 .029 -3 .563 .500 .313 .906 .625 .105 .039 .060 -4 .750 .688 .438 1.094 .750 .206 .067 .118 -5 .750 .688 .438 1.094 .750 .230 .075 .

10、132 -6 .875 .781 .438 1.188 .875 .283 .112 .163 -8 1.063 .906 .500 1.375 1.063 .360 .148 .207 -10 1.063 .906 .500 1.625 1.188 .450 .179 .259 -12 1.313 1.094 .625 1.703 1.438 .850 .284 .490 -16 1.625 1.313 .750 1.875 1.688 1.100 .410 .634 -20 1.875 1.500 .875 1.984 2.000 1.540 .600 .888 NOTES: NOTICE

11、 THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE.1. MATERIAL: SEE PROCUREMENT SPECIFICATION. ALLOY STEEL ALUMINUM ALLOY CORROSION RESISTANT STEEL TITANIUM ALLOY 2. FINISH: SEE PROCUREMENT SPECIFICATIO

12、N 3. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 4. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: DECIMALS .016, ANGLES 030. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,

13、-,-AEROSPACE STANDARD TEE, BULKHEAD, FLARELESS TUBE, INTERNAL THREAD ON RUN AS21911C SHEET 3 OF 4/5/ PART NUMBERS: DASH “-” IN PART NUMBER FOR 4130 ALLOY STEEL IS CANCELLED AND REPLACED, SEE TABLE 2 /A/ ADD “V(SIZE)P” IN PLACE OF DASH FOR CORROSION RESISTANT STEEL (15-5PH), CADMIUM PLATED ADD “V” IN

14、 PLACE OF DASH FOR CORROSION RESISTANT STEEL (15-5PH), NOT CADMIUM PLATED ADD “D” IN PLACE OF DASH FOR ALUMINUM ALLOY (2014): CANCELLED AND REPLACED, SEE TABLE 2 /C/ ADD “W” IN PLACE OF DASH FOR ALUMINUM ALLOY (7075) ADD “J” IN PLACE OF DASH FOR CORROSION RESISTANT STEEL (TYPE 304) ADD “K” IN PLACE

15、OF DASH FOR CORROSION RESISTANT STEEL (TYPE 316) ADD “R” AFTER DASH NUMBER FOR CORROSION RESISTANT STEEL (TYPE 321) ADD “S” AFTER DASH NUMBER FOR CORROSION RESISTANT STEEL (TYPE 347): CANCELLED, SEE TABLE 2 /D/ ADD “T” AFTER DASH NUMBER FOR TITANIUM ALLOY (6AL-4V) EXAMPLES OF PART NUMBERS: MS21911-4

16、 TEE, .250 TUBING, 4130 ALLOY STEEL IS CANCELLED AND REPLACED, SEE TABLE 2 /A/ MS21911V4P TEE, .250 TUBING, CORROSION RESISTANT STEEL (15-5PH), CADMIUM PLATED MS21911V4 TEE, .250 TUBING, CORROSION RESISTANT STEEL (15-5PH), NOT CADMIUM PLATED MS21911D4 TEE, .250 TUBING, ALUMINUM ALLOY (2014) IS CANCE

17、LLED AND REPLACED, SEE TABLE 2 /C/ MS21911W4 TEE, .250 TUBING, ALUMINUM ALLOY (7075) MS21911J4 TEE, .250 TUBING, CORROSION RESISTANT STEEL (TYPE 304) MS21911K4 TEE, .250 TUBING, CORROSION RESISTANT STEEL (TYPE 316) MS21911-4R TEE, .250 TUBING, CORROSION RESISTANT STEEL (TYPE 321) MS21911-4S TEE, .25

18、0 TUBING, CORROSION RESISTANT STEEL (TYPE 347) IS CANCELLED, SEE TABLE 2 /D/ MS21911-4T TEE, .250 TUBING, TITANIUM ALLOY (6AL-4V) 6. TITANIUM SHALL NOT BE USED FOR OXYGEN SYSTEMS. 7. SEE TABLE 2 FOR CANCELLED AND SUPERSEDED DOCUMENT AND PART NUMBERS. 8. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN

19、EFFECT ON DATE OF INVITATIONS FOR BID. 9. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE. 10. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PER

20、FORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST PRI-QPL-AS18280 FOR THIS STANDARD. SEE http:/ FOR CURRENT QPL ONLINE. 11. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1; UNLESS OTHERWIE SPECIFIED MACHINED SURFACES SHALL BE 125 Ra. 12. A CHANGE BAR ( l ) LOCATED IN THE

21、 LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHA

22、NGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 13. INTERPRETATION OF DRAWING PER ARP4296. 14. FLUID PASSAGE, HOLE CONTOUR: ARP4266 (OPTIONAL) Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction

23、 or networking permitted without license from IHS-,-,-AEROSPACE STANDARD TEE, BULKHEAD, FLARELESS TUBE, INTERNAL THREAD ON RUN AS21911C SHEET 4 OF 4TABLE 2 - CANCELLED AND SUPERSEDED DOCUMENT AND PART NUMBERS CANCELLEDDOCUMENT NUMBERPARTNUMBERSSUPERSESSIONNOTES SUPERSEDINGDOCUMENT NUMBERSUPERSEDINGP

24、ARTNUMBERSMS21911 MS21911-(2 THRU 20) /A/ AS21911 MS21911V(2 THRU 20)P MS21911 MS21911C(2 THRU 20) /B/ AS21911 MS21911J(2 THRU 20), MS21911K(2 THRU 20), OR MS21911-(2 THRU 20)R MS21911 MS21911D(2 THRU 20) /C/ AS21911 MS21911W(2 THRU 20) MS21911 MS21911W(2 THRU 20) NONE AS21911 MS21911W(2 THRU 20) MS

25、21911 MS21911J(2 THRU 20) NONE AS21911 MS21911J(2 THRU 20) MS21911 MS21911K(2 THRU 20) NONE AS21911 MS21911K(2 THRU 20) MS21911 MS21911-(2 THRU 20)R NONE AS21911 MS21911-(2 THRU 20)R MS21911 MS21911-(2 THRU 20)S /D/ AS21911 MS21911-(2 THRU 20)R MS21911 MS21911-(2 THRU 20)T NONE AS21911 MS21911-(2 TH

26、RU 20)T /A/ PARTS CODED “-” FOR 4130 ALLOY STEEL ARE NOT TO BE MANUFACTURED. PARTS CODED “V(SIZE)P” FOR CORROSION RESISTANT STEEL (15-5PH) WITH CADMIUM PLATE SHALL BE FURNISHED IN LIEU OF “-” CODED (4130) PARTS. PARTS CODED “-” FOR 4130 ALLOY STEEL MAY BE PROCURED UNTIL 12-31-06. /B/ PARTS CODED “C”

27、 FOR CORROSION RESISTANT STEEL (TYPE 303) ARE NOT TO BE MANUFACTURED. PARTS CODED “J”, “K” OR “R” FOR CORROSION RESISTANT STEEL (TYPES 304, 316, OR 321, RESPECTIVELY) SHALL BE FURNISHED IN LIEU OF “C” CODED PARTS AT SUPPLIERS OPTION. /C/ PARTS CODED “D” FOR ALUMINUM ALLOY 2014 ARE NOT TO BE MANUFACT

28、URED. PARTS CODED “W” FOR ALUMINUM ALLOY 7075 SHALL BE FURNISHED IN LIEU OF 2014 (D CODE) PARTS. PARTS CODED “D” FOR ALUMINUM ALLOY 2014 MAY BE PROCURED UNTIL 12-31-06. /D/ PARTS CODED “S” FOR CORROSION RESISTANT STEEL (TYPE 347) ARE NOT TO BE MANUFACTURED. PARTS CODED “S” MAY BE USED UNTIL EXISTING STOCK IS DEPLETED. PARTS CODED “R” FOR CORROSION RESISTANT STEEL (TYPE 321) SHALL BE FURNISHED IN LIEU OF “S” CODED PARTS. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-