SAE AS 21913D-2009 PLUG FLARELESS TUBE《无扩口管塞》.pdf

1、AEROSPACE STANDARD PLUG, FLARELESS TUBE AS21913Copyright 2009 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the pri

2、or written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1998-03REAFFIRMED 2007-07 REVISED 2009-09THIRD ANGLE PROJECTION CUSTODIAN: SAE

3、G-3/G-3B REV.DFEDERAL SUPPLY CLASS 4730 AS21913SHEET 1 OF 3REV. DPROCUREMENT SPECIFICATION: /11/ AS18280SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicab

4、ility and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE v

5、alues your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS21913DRATIONALE STANDARD UPDATED TO CORRECT SAE TEMPLATE TO ADD A REVISION BLOCK, ADD NEW DESIGN INACTIVATION IN ALIGNMENT WITH AS33514, CORRECTED TYPO IN TABLE 2; LAST COLUMN MS21913K

6、 WAS MS21913J, AND GENERAL SAE UPDATING AND CLARIFICATION. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS21913E. THIS SAE STANDARD RETAINS THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. FIGURE 1 - PLUG, FLARELESS TUBE TABLE

7、 1 - DIMENSIONS DASHNO/5/NOMINAL TUBE SIZEREF (T) THREAD AS8879A+.000-.047 B C WEIGHT, LB/EA, APPROX, REF STEELALALLOYTIALLOY2 .125 .3125-24 UNJF-3A .375 .563 .428- .440 .014 .005 .008 3 .188 .3750-24 UNJF-3A .438 .609 .428- .440 .017 .006 .009 4 .250 .4375-20 UNJF-3A .438 .641 .490- .502 .020 .007

8、.011 5 .313 .5000-20 UNJF-3A .500 .672 .552- .565 .026 .010 .015 6 .375 .5625-18 UNJF-3A .500 .719 .615- .628 .033 .012 .019 8 .500 .7500-16 UNJF-3A .563 .844 .802- .815 .067 .024 .038 10 .625 .8750-14 UNJF-3A .625 .984 .928- .941 .107 .038 .061 12 .750 1.0625-12 UNJ-3A .688 1.031 1.113-1.128 .174 .

9、062 .100 16 1.000 1.3125-12 UNJ-3A .688 1.063 1.363-1.380 .245 .091 .141 20 1.250 1.6250-12 UNJ-3A .625 1.094 1.676-1.693 .390 .150 .225 24 /8/ 1.500 1.8750-12 UNJ-3A .719 1.094 1.988-2.005 .540 .192 .311 32 /8/ 2.000 2.5000-12 UNJ-3A .688 1.094 2.609-2.635 .965 .354 .556 INACTIVE FOR NEW DESIGN /13

10、/ Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS21913SHEET 2 OF 3REV. DPLUG, FLARELESS TUBE NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MA

11、TERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE.1. MATERIAL: SEE PROCUREMENT SPECIFICATION. ALLOY STEEL ALUMINUM ALLOY CORROSION RESISTANT STEEL TITANIUM ALLOY 2. FINISH: SEE PROCUREMENT SPECIFICATION. 3. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 4. DIMENSION

12、S ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: DECIMALS .016, ANGLES 030. /5/ PART NUMBERS: DASH “-” IN PART NUMBER FOR 4130 ALLOY STEEL IS CANCELLED AND REPLACED, SEE TABLE 2 /A/ ADD “V(SIZE)P” IN PLACE OF DASH FOR CORROSION RESISTANT STEEL (15-5PH), CADMIUM PLATED ADD “V” IN PLACE OF DAS

13、H FOR CORROSION RESISTANT STEEL (15-5PH), NOT CADMIUM PLATED ADD “D” IN PLACE OF DASH FOR ALUMINUM ALLOY (2024): CANCELLED AND REPLACED, SEE TABLE 2 /C/ ADD “W” IN PLACE OF DASH FOR ALUMINUM ALLOY (7075) ADD “J” IN PLACE OF DASH FOR CORROSION RESISTANT STEEL (TYPE 304) ADD “K” IN PLACE OF DASH FOR C

14、ORROSION RESISTANT STEEL (TYPE 316) ADD “R” AFTER DASH NUMBER FOR CORROSION RESISTANT STEEL (TYPE 321) ADD “S” AFTER DASH NUMBER FOR CORROSION RESISTANT STEEL (TYPE 347): CANCELLED, SEE TABLE 2 /D/ ADD “T” AFTER DASH NUMBER FOR TITANIUM ALLOY (6AL-4V) EXAMPLES OF PART NUMBERS: PART MARKING REQUIREME

15、NTS PER PROCUREMENT SPECIFICATION. MS21913-4 PLUG, .250 TUBING, 4130 ALLOY STEEL IS CANCELLED AND REPLACED, SEE TABLE 2 /A/ MS21913V4P PLUG, .250 TUBING, CORROSION RESISTANT STEEL (15-5PH), CADMIUM PLATED MS21913V4 PLUG, .250 TUBING, CORROSION RESISTANT STEEL (15-5PH), NOT CADMIUM PLATED MS21913D4 P

16、LUG, .250 TUBING, ALUMINUM ALLOY (2024) IS CANCELLED AND REPLACED, SEE TABLE 2 /C/ MS21913W4 PLUG, .250 TUBING, ALUMINUM ALLOY (7075) MS21913J4 PLUG, .250 TUBING, CORROSION RESISTANT STEEL (TYPE 304) MS21913K4 PLUG, .250 TUBING, CORROSION RESISTANT STEEL (TYPE 316) MS21913-4R PLUG, .250 TUBING, CORR

17、OSION RESISTANT STEEL (TYPE 321) MS21913-4S PLUG, .250 TUBING, CORROSION RESISTANT STEEL (TYPE 347) IS CANCELLED, SEE TABLE 2 /D/ MS21913-4T PLUG, .250 TUBING, TITANIUM ALLOY (6AL-4V) 6. FLUID PASSAGE, HOLE CONTOUR: ARP4266 (OPTIONAL). 7. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994./8/ DRILL POIN

18、T NOT PERMITTED ON -24 AND -32 SIZES, HOLE SHALL BE FLAT BOTTOMED IN ACCORDANCE DIMENSION A. 9. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATIONS FOR BID. 10. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS STAN

19、DARD SHALL TAKE PRECEDENCE. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS21913SHEET 3 OF 3REV. DPLUG, FLARELESS TUBE /11/ PROCUREMENT SPECIFICATION: AS18280 EXCEPT AS SPECIFIE

20、D ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS18280 FOR THIS STANDARD. SEE FOR CURRENT QPL ON-LINE. 12. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M

21、; REQUIREMENTS PER ASME B46.1; UNLESS OTHERWISE SPECIFIED MACHINED SURFACES SHALL BE 125 Ra. /13/ ALL PART NUMBERS MS21913 IN ACCORDANCE WITH AS21913 ARE INACTIVE FOR NEW DESIGN EFFECTIVE AUGUST 2009. FOR NEW DESIGN USE AS5231( ).14. A CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIEN

22、CE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN

23、ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 15. INTERPRETATION OF DRAWING PER ARP4296. TABLE 2 - CANCELLED, SUPERSEDED DOCUMENTS AND PART NUMBERS CANCELLED DOCUMENT NUMBER PARTNUMBERS SUPERSESSIONNOTES SUPERSEDINGDOCUMENT NUMBER SUPERSEDINGPARTNUMBERS MS21913 MS21913

24、-(2 THRU 32) /A/ AS21913 MS21913V(2 THRU 32)P MS21913 MS21913C(2 THRU 32) /B/ AS21913 MS21913J(2 THRU 32), MS21913K(2 THRU 32),OR MS21913-(2 THRU 32)R MS21913 MS21913D(2 THRU 32) /C/ AS21913 MS21913W(2 THRU 32) MS21913 MS21913W(2 THRU 32) NONE AS21913 MS21913W(2 THRU 32) MS21913 MS21913J(2 THRU 32)

25、NONE AS21913 MS21913J(2 THRU 32) MS21913 MS21913K(2 THRU 32) NONE AS21913 MS21913K(2 THRU 32) MS21913 MS21913-(2 THRU 32)R NONE AS21913 MS21913-(2 THRU 32)R MS21913 MS21913-(2 THRU 32)S /D/ AS21913 MS21913-(2 THRU 32)R MS21913 MS21913-(2 THRU 32)T NONE AS21913 MS21913-(2 THRU 32)T /A/ PARTS CODED “-

26、” FOR 4130 ALLOY STEEL ARE NOT TO BE MANUFACTURED. PARTS CODED “V(SIZE)P” FOR CORROSION RESISTANT STEEL (15-5PH) WITH CADMIUM PLATE SHALL BE FURNISHED IN LIEU OF “-” CODED (4130) PARTS. PARTS CODED “-” FOR 4130 ALLOY STEEL MAY BE PROCURED UNTIL 12-31-06. /B/ PARTS CODED “C” FOR CORROSION RESISTANT S

27、TEEL (TYPE 303) ARE NOT TO BE MANUFACTURED. PARTS CODED “J”, “K” OR “R” FOR CORROSION RESISTANT STEEL (TYPES 304, 316, OR 321, RESPECTIVELY) SHALL BE FURNISHED IN LIEU OF “C” CODED PARTS AT SUPPLIERS OPTION. /C/ PARTS CODED “D” FOR ALUMINUM ALLOY 2024 ARE NOT TO BE MANUFACTURED. PARTS CODED “W” FOR

28、ALUMINUM ALLOY 7075 SHALL BE FURNISHED IN LIEU OF 2024 (D CODE) PARTS. PARTS CODED “D” FOR ALUMINUM ALLOY 2024 MAY BE PROCURED UNTIL 12-31-06. /D/ PARTS CODED “S” FOR CORROSION RESISTANT STEEL (TYPE 347) ARE NOT TO BE MANUFACTURED. PARTS CODED “S” MAY BE USED UNTIL EXISTING STOCK IS DEPLETED. PARTS CODED “R” FOR CORROSION RESISTANT STEEL (TYPE 321) SHALL BE FURNISHED IN LIEU OF “S” CODED PARTS. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-