SAE AS 22520 18-2012 CRIMPING TOOLS TERMINAL HAND WIRE TERMINATION IN-SERVICE INSPECTION GAGES FOR AS22520 17 CRIMP TOOLS《电线端接用手动终端压接工具 AS22520 17压接工具在用检验量规》.pdf

1、 AEROSPACE STANDARD CRIMPING TOOLS, TERMINAL, HAND, WIRE TERMINATION; IN-SERVICE INSPECTION GAGES FOR AS22520/17 CRIMP TOOLS AS2252018Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by an

2、y means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.

3、org ISSUED2012-01REAFFIRMED 2016-11THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 FEDERAL SUPPLY CLASS 5220 AS22520 18 SHEET 1 OF 2 PROCUREMENT SPECIFICATION: AS22520 6$(7HFKQLFDO6WDQGDUGV%RDUG5XOHVSURYLGHWKDW7KLVUHSRUWLVSXEOLVKHGE6$(WRDGYDQFHWKHVWDWHRItechnicaland engineering sciences. The useof thi

4、s report is entirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,LVWKHVROHUHVSRQVLELOLWRIWKHXVHUSAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. S

5、AE invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS22520/18 RATIONALE AS22520/18 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICE THE REQUIREMENTS FOR PRO

6、CURING THE CONTACTS DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF: SAE AS22520 FIGURE 1 AS22520/18 GAGE CONFIGURATION AEROSPACE STANDARD AS22520 18 SHEET 2 OF 2 CRIMPING TOOLS, TERMINAL, HAND, WIRE TERMINATION; IN-SERVICE INSPECTION GAGES FOR AS22520/17 CRIMP TOOLS TAB

7、LE 1 CONFIGURATION AND GAGE APPLICATIONS PART NO. M22520/ 18- A DIA. .005 BETWEEN CENTER LINES B +.000 -.010 C +.000 -.010 D DIA. .005 BETWEEN CENTER LINES E .0002 DIA. F .0002 DIA. STAMPING / MARKING USE FOR INSPECTION OF BASIC TOOLS (REF) SURFACE G .093 HIGH SURFACE H .093 HIGH SURFACE J .062 HIGH

8、 SURFACE K .062 HIGH 1 .040 .655 .655 .040 .0292 .0350 .0292 .0350 M22520/17-01 BASIC TOOL SET CON AT NO. 1 CHROME PLATE WITH ADEQUATE COVERAGE FOR CORROSION AND WEAR RESISTANCE PER AMS-QQ-C-320 PLATING CHROMIUM, CLASS I, TYPE II WITH A THICKNESS OF .00003 INCHES MINIMUM. HANDLE: PAINTED AS SPECIFIE

9、D IN FIGURE 1. PAINT MAY FADE AFTER AS22520 PERFORMANCE TESTS, BUT COLOR SHALL BE DISTINGUISHABLE. 4. MARKING: UNLESS OTHERWISE SPECIFIED, STAMPING SHALL BE INDENTED. LASER MARKING IS ALSO ACCEPTABLE. 5. STORAGE CONTAINER: EACH GAGE SHALL BE FURNISHED WITH A SUITABLE CONTAINER. APPLICATION NOTES: 1. GAGES ARE USED AS GO/NO-GO VERIFICATION INSPECTION GAGES FOR AS22520/17 CRIMP TOOLS.