SAE AS 22520 20-2014 CRIMPING TOOL TYPE 2 TERMINAL HAND WIRE TERMINATION FOR SIZE 16 SHIELDED CONTACTS (SHIELD CRIMP SLEEVE)《尺寸为16的屏蔽接触 (屏蔽卷曲套筒) 用线终端手动终端的2型压接工具》.pdf

1、AEROSPACE STANDARD CRIMPING TOOL, TYPE 2, TERMINAL, HAND, WIRE TERMINATION FOR SIZE 16 SHIELDED CONTACTS (SHIELD CRIMP SLEEVE) AS22520/20Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by

2、 any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.s

3、ae.org ISSUED 2014-05THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120 AS22520/20SHEET 1 OF 7PROCUREMENT SPECIFICATION: AS22520SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineeringsciences.The useofthis re

4、portisentirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SA

5、E invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS22520/20RATIONALE AS22520/20 PERMITS THE CANCELLATION AND SUPERSESSION OF MIL-C-22520 /20 WITH THIS DOCUMENT. IT INCLUDES ENGINEERING

6、 POSITION LETTERS, MILITARY SPECIFICATION AMENDMENTS, AND MINOR TECHNICAL CHANGES REQUIRED TO REFLECT THE APPROVED QUALIFIED TOOLS. GOVERNMENT DOCUMENTATION REFERENCES ARE REMOVED AND INDEX ADDED AS TABLE 1. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF

7、 THIS DOCUMENT AND THE LATEST ISSUE OF AS22520. TABLE 1 - M22520/20 POSITIONER-CONTACT ACCOMMODATION INFORMATION POSITIONER PART NUMBER M22520/20 AS39029 OUTER CONTACT APPLICATION (M39029/XX-YYY) POSITIONER INFORMATION (SHEET NO.) -02 /19-181, /21-187 SHIELD CRIMP SLEEVE 4 -03 /20-184FIGURE 1 - M225

8、20/20-01 TOOL AEROSPACE STANDARD AS22520/20SHEET 2 OF 7CRIMPING TOOL, TYPE 2, TERMINAL, HAND, WIRE TERMINATION FOR SIZE 16 SHIELDED CONTACTS (SHIELD CRIMP SLEEVE) RETAINER RING (LOCK PLATE) RETAINER RING (LOCK PLATE) DETAIL A-A TOOL POSITIONER LOCATOR FIGURE 1 - M22520/20-01 TOOL (CONTINUED)AEROSPAC

9、E STANDARD AS22520/20SHEET 3 OF 7CRIMPING TOOL, TYPE 2, TERMINAL, HAND, WIRE TERMINATION FOR SIZE 16 SHIELDED CONTACTS (SHIELD CRIMP SLEEVE) TOOL INDENTERS TOOL RETAINER FIGURE 1 - M22520/20-01 TOOL (CONTINUED) AEROSPACE STANDARD AS22520/20SHEET 4 OF 7CRIMPING TOOL, TYPE 2, TERMINAL, HAND, WIRE TERM

10、INATION FOR SIZE 16 SHIELDED CONTACTS (SHIELD CRIMP SLEEVE) DETAIL 1 FIGURE 2 - M22520/20 POSITIONER CONSTRUCTION M22520/20-02 AND -03 POSITIONER DATA PLATES FIGURE 3 - DATA PLATE MARKING REQUIREMENTS (SEE APPLICATION NOTE) AEROSPACE STANDARD AS22520/20SHEET 5 OF 7CRIMPING TOOL, TYPE 2, TERMINAL, HA

11、ND, WIRE TERMINATION FOR SIZE 16 SHIELDED CONTACTS (SHIELD CRIMP SLEEVE) M22520/20-01 TOOL DATA PLATE (SEE APPLICATION NOTE) FIGURE 3 - DATA PLATE MARKING REQUIREMENTS (CONTINUED) TABLE 2 - BASIC TOOL MARKINGS PART NO. BODY COLOR HANDLE GRIP COLOR HANDLE GRIP B COLOR FOR INSPECTION GAGING USE INDENT

12、ER RETAINER M22520/20-01 BLUE GREEN BLUE M22520/3-4 1/ M22520-3-6 2/ 1/ INSPECTION GAGE ONLY APPLICABLE FOR THE TOOL SET AT SELECTOR POSITION NUMBER 7 (SEE APPLICATION NOTES). 2/ INSPECTION GAGE ONLY APPLICABLE FOR THE TOOL SET AT SELECTOR POSITION NUMBER 8 (SEE APPLICATION NOTES). TABLE 3 - INDENTE

13、R GAGE LIMITS SELECTORNUMBER INSPECTION GAGE DIAMETERS (INCHES) 1/ GO A + .0001 NO-GO B + .0001 1 .0430 .04602 .0460 .04903 .0490 .05204 .0520 .0550 5 .0560 .05906 .0600 .06307 .0640 .06708 .0690 .0720 1/ SEE FIGURE 1 TOOL INDENTER AND RETAINER. AEROSPACE STANDARD AS22520/20SHEET 6 OF 7CRIMPING TOOL

14、, TYPE 2, TERMINAL, HAND, WIRE TERMINATION FOR SIZE 16 SHIELDED CONTACTS (SHIELD CRIMP SLEEVE) TABLE 4 - RETAINER GAGE LIMITS SELECTORNUMBER INSPECTION GAGE DIAMETERS (INCHES) GO A + .0001 NO-GO B + .0001 8 .0740 .0770TABLE 5 - POSITIONER DETAILS PART NUMBER M22520/20 BODY COLOR A DIA. +.002 -.000 B

15、 DIA. .002 C DIA. +.002 -.000 -02 GREEN .081 .160.049-03 .490 REQUIREMENTS: THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS22520. 1. DIMENSIONS UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES, TOLERANCES (DECIMALS .0

16、10, ANGLES 1/2). OUTLINE CONFIGURATION OPTIONAL WITHIN MAXIMUM DIMENSIONS SHOWN FIGURES 1 AND 2. BREAK ALL INDENTER TIP EDGES .002 TO .004 R. BREAK ALL OTHER SHARP EDGES .005 R MAX. 2. MATERIALS UNLESS OTHERWISE SPECIFIED, MATERIAL SHALL BE IN ACCORDANCE WITH AS22520. ALUMINUM SURFACE TEXTURE SHALL

17、BE 63 RMS OVER ALL IN ACCORDANCE WITH ASA B46 1-1962 (ANSI). 2.1 INDENTER MATERIAL SHALL BE OIL HARDEN TOOL STEEL. INDENTER MATERIAL SHALL BE HARDENED TO ROCKWELL “C“ 56-58. 2.2 POSITIONER BODY MATERIAL SHALL BE ALUMINUM AMS- QQ-A-225/6. LOCATOR PLATE SHALL BE STAINLESS STEEL PER AMS-QQ-S-763, CLASS

18、 304, CONDITION A. 3. IDENTIFICATION MARKING AND COLOR 3.1 TOOL FRAME IDENTIFICATION SHALL BE MARKED IN ACCORDANCE WITH MIL-STD-130, STAMP (LETTERING HEIGHT IS .093 MIN AND WHITE FILL) OR LASER MARKED. TOOL FRAME IDENTIFICATION SHALL INCLUDE THE TOOL PART NUMBER, INSPECTION GAGE NUMBER, AND COLOR SP

19、ECIFIED IN TABLE 1. ADDITIONAL TOOL FRAME MARKING SHALL BE AS SHOWN IN FIGURE 1. 3.2 POSITIONERS SHALL BE MARKED AS SHOWN IN FIGURE 2. MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-130, STAMP (LETTERING HEIGHT IS .093 MIN AND WHITE FILL) OR LASER MARKED. POSITIONER COLOR SHALL BE GREEN. 3.3 DATA PLATE

20、S BE SHALL CLEARLY MARKED AS SHOWN IN FIGURE 3 AND BE READABLE AFTER ALL REQUIREMENTS SPECIFIED IN AS22520. 4. WEIGHT WEIGHT OF TOOL FRAME WITHOUT POSITIONER SHALL NOT EXCEED 1.0 POUNDS AND THE POSITIONER SHALL NOT EXCEED .75 OUNCES. 5. TOOL CRIMP FORCE CRIMP FORCE REQUIRED TO MAKE SATISFACTORY CRIM

21、PS SHALL NOT EXCEED 65 POUNDS WHEN CRIMPING A M39029/19-181 CONTACT. 6. TOOL FRAME INDENTER GAGE LIMITS INDENTER GO AND NO-GO INSPECTION GAGE LIMITS ARE DEFINED IN TABLE 3 AND 4 (SEE APPLICATION NOTES). 7. POSITIONER 7.1 LOCK PLATE THE POSITIONER LOCK PLATE SHALL PROVIDE POSITIVE DETENT FOR BAYONET

22、LOCK PINS, AND A MEANS OF SECURING THE POSITIONER SO THAT IT CANNOT BE REMOVED WITHOUT REMOVING A LOCKING PIN OR WIRE. AEROSPACE STANDARD AS22520/20SHEET 7 OF 7CRIMPING TOOL, TYPE 2, TERMINAL, HAND, WIRE TERMINATION FOR SIZE 16 SHIELDED CONTACTS (SHIELD CRIMP SLEEVE) 7.2 LOCATOR POSITIONER LOCATOR S

23、HALL BE SPRING LOADED. SPRING SHALL DEPRESS .031 INCHES WITH A FORCE OF 2 POUNDS 1 POUNDS. 7.3 RETAINER RETAINERS MUST BE FULLY CLOSED BEFORE INDENTERS START THE CRIMP. 8. PART NUMBER STRUCTURE M22520/20 -02 I I I I_ POSITIONER (SEE TABLE 1) OR BASIC TOOL (SEE TABLE 5) I_ DETAIL SPECIFICATION NUMBER

24、 QUALIFICATION: 1. QUALIFICATION INSPECTION NOT REQUIRED. FOR EACH PURCHASE QUALITY CONFORMANCE INSPECTION IS REQUIRED. APPLICATION NOTES: 1. FOR APPLICABLE CONTACTS FOR EACH POSITIONERS SEE TABLE 1. 2. UNLESS OTHERWISE SPECIFIED, FOR TOOL APPLICATIONS INSPECTION GAGING IS RECOMMENDED TO BE PERFORME

25、D WITH THE GAGE SPECIFIED IN TABLE 2 ON TOOL SELECTOR NUMBER 7 OR 8. WHEN OTHER SELECTOR SETTING GAGING IS REQUIRED, INSPECTION GAGES SHALL BE IN ACCORDANCE WITH TABLE 3. 3. IN FIGURE 3, THE M39029/19-01, /20-01 AND /21-01 CONTACT PART NUMBERS ARE SUPPLIER COMMERCIAL PART NUMBERS ORIGINAL USED BY TH

26、E MILITARY. THE PART NUMBERS ARE PROVIDED FOR MAINTENANCE PURPOSES. 4. ON THE M22520/20-01 TOOL FRAME DATA PLATE, IN SOME CASES, NO KNOWN STANDARD CABLES EXIST TO REPLACE THE LISTED COMMERCIAL CABLES OR THE CABLES ARE NO LONGER MANUFACTURED. THE INFORMATION IS RETAINED FOR CABLE LEGACY REQUIREMENTS.

27、 THE STANDARD CABLES LISTED IN AS39029/19 THRU /21 ARE RECOMMENDED TO BE USED WHEN POSSIBLE. 5. AS22520/20 CRIMP TOOL CONFIGURATION IS FOR HAND CRIMPING ONLY. NOTICE USE OF HAND CRIMPING TOOLS COVERED BY THIS SPECIFICATION AS A COMPONENT IN ANY POWERED “PRESS” MAY VIOLATE OSHA REGULATIONS CFR 1910.2

28、11. SUPERSESSION:1. AS22520/20 SUPERSEDES MIL-C-22520/20 WITHOUT QUALIFICATION REQUIREMENTS. PART NUMBERS REMAIN UNCHANGED. SPECIFICATION NOTE: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.