SAE AS 22520 22-2014 CRIMPING TOOL TYPE 2 TERMINAL HAND WIRE TERMINATION FOR SIZE 12 SHIELDED CONTACTS (SHIELD CRIMP SLEEVE)《尺寸为12的屏蔽接触 (屏蔽卷曲套筒) 用线终端手动终端的2型压接工具》.pdf

1、AEROSPACE STANDARD CRIMPING TOOL, TYPE 2, TERMINAL, HAND, WIRE TERMINATION FOR SIZE 12 SHIELDED CONTACTS (SHIELD CRIMP SLEEVE) AS22520/22Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by

2、 any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.s

3、ae.org ISSUED 2014-05THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120 AS22520/22SHEET 1 OF 7PROCUREMENT SPECIFICATION: AS22520SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineeringsciences.The useofthis re

4、portisentirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SA

5、E invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS22520/22RATIONALE AS22520/22 PERMITS THE CANCELLATION AND SUPERSESSION OF MIL-C-22520 /22 WITH THIS DOCUMENT. IT INCLUDES ENGINEERING

6、 POSITION LETTERS, MILITARY SPECIFICATION AMENDMENTS, AND MINOR TECHNICAL CHANGES REQUIRED TO REFLECT THE APPROVED QUALIFIED TOOLS. GOVERNMENT DOCUMENTATION REFERENCES ARE REMOVED AND INDEX ADDED AS TABLE 1. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF

7、 THIS DOCUMENT AND THE LATEST ISSUE OF AS22520. TABLE 1 - M22520/22 POSITIONER-CONTACT ACCOMMODATION INFORMATION POSITIONER PART NUMBER M22520/20 AS39029 OUTER CONTACT APPLICATION (M39029/XX-YYY) POSITIONER INFORMATION (SHEET NO.) -02 /19-182, /19-183 /21-188, /22-189 SHIELD CRIMP SLEEVE4-03 /20-185

8、, /21-186 FIGURE 1 - M22520/22-01 TOOL AEROSPACE STANDARD AS22520/22SHEET 2 OF 7CRIMPING TOOL, TYPE 2, TERMINAL, HAND, WIRE TERMINATION FOR SIZE 12 SHIELDED CONTACTS (SHIELD CRIMP SLEEVE) RETAINER RING (LOCK PLATE) RETAINER RING (LOCK PLATE) DETAIL A-A TOOL POSITIONER LOCATOR FIGURE 1 - M22520/22-01

9、 TOOL (CONTINUED) AEROSPACE STANDARD AS22520/22SHEET 3 OF 7CRIMPING TOOL, TYPE 2, TERMINAL, HAND, WIRE TERMINATION FOR SIZE 12 SHIELDED CONTACTS (SHIELD CRIMP SLEEVE) TOOL INDENTERS TOOL RETAINER FIGURE 1 - M22520/22-01 TOOL (CONTINUED) AEROSPACE STANDARD AS22520/22SHEET 4 OF 7CRIMPING TOOL, TYPE 2,

10、 TERMINAL, HAND, WIRE TERMINATION FOR SIZE 12 SHIELDED CONTACTS (SHIELD CRIMP SLEEVE) DETAIL 1 FIGURE 2 - M22520/22 POSITIONER CONSTRUCTION M22520/22-02 AND -04 POSITIONER DATA PLATES FIGURE 3 - DATA PLATE MARKING REQUIREMENTS AEROSPACE STANDARD AS22520/22SHEET 5 OF 7CRIMPING TOOL, TYPE 2, TERMINAL,

11、 HAND, WIRE TERMINATION FOR SIZE 12 SHIELDED CONTACTS (SHIELD CRIMP SLEEVE) M22520/22-01 TOOL DATA PLATE (SEE APPLICATION NOTE) FIGURE 3 - DATA PLATE MARKING REQUIREMENTS (CONTINUED) TABLE 2 - BASIC TOOL MARKINGS PART NO. BODY COLOR HANDLE GRIP COLOR HANDLE GRIP B COLOR FOR INSPECTION GAGING USE IND

12、ENTER RETAINER M22520/22-01 BLUE GREEN BLACK M22520/3-4 1/ M22520-3-8 2/ 1/ INSPECTION GAGE ONLY APPLICABLE FOR THE TOOL SET AT SELECTOR POSITION NUMBER 1 (SEE APPLICATION NOTES). 2/ INSPECTION GAGE ONLY APPLICABLE FOR THE TOOL SET AT SELECTOR POSITION NUMBER 8 (SEE APPLICATION NOTES). TABLE 3 - IND

13、ENTER GAGE LIMITS SELECTORNUMBER INSPECTION GAGE DIAMETERS (INCHES) 1/ GO A .0001 NO-GO B .0001 1 .0640 .06702 .0670 .07003 .0700 .07304 .0730 .0760 5 .0770 .08006 .0810 .08407 .0850 .08808 .0900 .0930 1/ SEE FIGURE 1 TOOL INDENTER AND RETAINER. TABLE 4 - RETAINER GAGE LIMITS SELECTORNUMBER INSPECTI

14、ON GAGE DIAMETERS (INCHES) GO A .0001 NO-GO B .0001 8 .1210 .1240AEROSPACE STANDARD AS22520/22SHEET 6 OF 7CRIMPING TOOL, TYPE 2, TERMINAL, HAND, WIRE TERMINATION FOR SIZE 12 SHIELDED CONTACTS (SHIELD CRIMP SLEEVE) TABLE 5 - POSITIONER DETAILS PART NUMBER M22520/22 BODY COLOR A DIA. +.002 -.000 B DIA

15、. .002 C DIA. +.002 -.000 -02 GREEN .129 .160.093-03 .490 REQUIREMENTS: THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF AS22520. 1. DIMENSIONS UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES, TOLERANCES (DECIMALS .010,

16、ANGLES 1/2). OUTLINE CONFIGURATION OPTIONAL WITHIN MAXIMUM DIMENSIONS SHOWN FIGURES 1 AND 2. BREAK ALL INDENTER TIP EDGES .002 TO .004 R. BREAK ALL OTHER SHARP EDGES .005 R MAX. 2. MATERIALS UNLESS OTHERWISE SPECIFIED, MATERIAL SHALL BE IN ACCORDANCE WITH AS22520. ALUMINUM SURFACE TEXTURE SHALL BE 6

17、3 RMS OVER ALL IN ACCORDANCE WITH ASA B46 1-1962 (ANSI). 2.1 INDENTER MATERIAL SHALL BE OIL HARDEN TOOL STEEL. INDENTER MATERIAL SHALL BE HARDENED TO ROCKWELL “C“ 56-58. 2.2 POSITIONER BODY MATERIAL SHALL BE ALUMINUM AMS-QQ-A-225/6. LOCATOR PLATE SHALL BE STAINLESS STEEL PER AMS-QQ-S-763, CLASS 304,

18、 CONDITION A. 3. IDENTIFICATION MARKING AND COLOR 3.1 TOOL FRAME IDENTIFICATION SHALL BE MARKED IN ACCORDANCE WITH MIL-STD-130, STAMP (LETTERING HEIGHT IS .093 MIN AND WHITE FILL) OR LASER MARKED. TOOL FRAME IDENTIFICATION SHALL INCLUDE THE TOOL PART NUMBER, INSPECTION GAGE NUMBER, AND COLOR SPECIFI

19、ED IN TABLE 1. ADDITIONAL TOOL FRAME MARKING SHALL BE AS SHOWN IN FIGURE 1. 3.2 POSITIONERS SHALL BE MARKED AS SHOWN IN FIGURE 2. MARKING SHALL BE IN ACCORDANCE WITH MIL-STD-130, STAMP (LETTERING HEIGHT IS .093 MIN AND WHITE FILL) OR LASER MARKED. POSITIONER COLOR SHALL BE GREEN. 3.3 DATA PLATES BE

20、SHALL CLEARLY MARKED AS SHOWN IN FIGURE 3 AND BE READABLE AFTER ALL REQUIREMENTS SPECIFIED IN AS22520. 4. WEIGHT WEIGHT OF TOOL FRAME WITHOUT POSITIONER SHALL NOT EXCEED 1.0 POUNDS AND THE POSITIONER SHALL NOT EXCEED .75 OUNCES. 5. TOOL CRIMP FORCE CRIMP FORCE REQUIRED TO MAKE SATISFACTORY CRIMPS SH

21、ALL NOT EXCEED 65 POUNDS WHEN CRIMPING A M39029/19-182 CONTACT. 6. TOOL FRAME INDENTER GAGE LIMITS INDENTER GO AND NO-GO INSPECTION GAGE LIMITS ARE DEFINED IN TABLE 3 AND 4 (SEE APPLICATION NOTES). 7. POSITIONER 7.1 LOCK PLATE THE POSITIONER LOCK PLATE SHALL PROVIDE POSITIVE DETENT FOR BAYONET LOCK

22、PINS, AND A MEANS OF SECURING THE POSITIONER SO THAT IT CANNOT BE REMOVED WITHOUT REMOVING A LOCKING PIN OR WIRE. 7.2 LOCATOR POSITIONER LOCATOR SHALL BE SPRING LOADED. SPRING SHALL DEPRESS .031 INCHES WITH A FORCE OF 2 POUNDS 1 POUNDS. 7.3 RETAINER RETAINERS MUST BE FULLY CLOSED BEFORE INDENTERS ST

23、ART THE CRIMP. AEROSPACE STANDARD AS22520/22SHEET 7 OF 7CRIMPING TOOL, TYPE 2, TERMINAL, HAND, WIRE TERMINATION FOR SIZE 12 SHIELDED CONTACTS (SHIELD CRIMP SLEEVE) 8. PART NUMBER STRUCTURE M22520/22 -02 I I I I_ POSITIONER (SEE TABLE 1) OR BASIC TOOL (SEE TABLE 5) I_ DETAIL SPECIFICATION NUMBER QUAL

24、IFICATION: 1. QUALIFICATION INSPECTION NOT REQUIRED. FOR EACH PURCHASE QUALITY CONFORMANCE INSPECTION IS REQUIRED. APPLICATION NOTES: 1. FOR APPLICABLE CONTACTS FOR EACH POSITIONERS SEE TABLE 1. 2. UNLESS OTHERWISE SPECIFIED, FOR TOOL APPLICATIONS INSPECTION GAGING IS RECOMMENDED TO BE PERFORMED WIT

25、H THE GAGE SPECIFIED IN TABLE 2 ON TOOL SELECTOR NUMBER 1 OR 8. WHEN OTHER SELECTOR SETTING GAGING IS REQUIRED, INSPECTION GAGES SHALL BE IN ACCORDANCE WITH TABLE 3. 3. AS22520/22 SUPERSEDES MIL-C-22520/22. PART NUMBERS REMAIN UNCHANGED. 4. IN FIGURE 3, THE M39029/19-01, /20-01 AND /21-01 CONTACT PA

26、RT NUMBERS ARE SUPPLIER COMMERCIAL PART NUMBERS ORIGINAL USED BY THE MILITARY. THE PART NUMBERS ARE PROVIDED FOR MAINTENANCE PURPOSES. 5. ON THE M22520/22-01 TOOL FRAME DATA PLATE, IN SOME CASES, NO KNOWN STANDARD CABLES EXIST TO REPLACE THE LISTED COMMERCIAL CABLES OR THE CABLES ARE NO LONGER MANUF

27、ACTURED. THE INFORMATION IS RETAINED FOR CABLE LEGACY REQUIREMENTS. THE STANDARD CABLES LISTED IN AS39029/19 THRU /21 ARE RECOMMENDED TO BE USED WHEN POSSIBLE. 6. AS22520/19 CRIMPING TOOL CONFIGURATION IS FOR HAND CRIMPING ONLY. NOTICE USE OF HAND CRIMPING TOOLS COVERED BY THIS SPECIFICATION AS A CO

28、MPONENT IN ANY POWERED “PRESS” MAY VIOLATE OSHA REGULATIONS CFR 1910.211 SUPERSESSION:1. AS22520/22 SUPERSEDES MIL-C-22520/22 WITHOUT QUALIFICATION REQUIREMENTS. PART NUMBERS REMAIN UNCHANGED. SPECIFICATION NOTE: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LO

29、CATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.